Core Products Coniston DK221 User manual

Thank you for choosing this furniture.
BEFORE YOU START ASSEMBLY please store the carton for 48 hours or more so the contents can acclimatise.
PLEASE RETAIN ALL PACKING UNTIL YOU HAVE COMPLETED ASSEMBLY.
Information about your furniture.
Our furniture ranges have been carefully crafted from solid wood and natural wood veneers. Each piece of furniture has unique
characteristics such as knots, variances and graniing. These are part of the natural character of the furniture itself.
Caring for your furniture.
Extreme temperature can cause slight movements in the wood itself so please avoid placing your furniture close to radiators or other direct
sources of heat. Humidity should also be avoided. Please avoid exposing your furniture to continued bright sunlight as it can affect the colour.
Any fluid should be removed as quickly as possible. Always lift your furniture when moving, as dragging can cause damage to your furniture or
flooring. Extreme changes in temperature & humidity during transit may result in a powder residue forming so silica gel bags have been included
to alleviate this natural occurrence. This residue is harmless and can easily be removed before assembly with a damp cloth and mild detergent.
After care.
Wipe the surfaces with a dry cloth and an occasional use of normal household polish. We also recommend you use household spray
polish occasionally on the drawer grooves and runners as this will aid use. Please do not use detergents or chemicals on your furniture.
PARTS LIST
BEFORE YOU START ASSEMBLY
Please check that you have all the correct parts and fittings as detailed on the assembly instructions.
FOR DAMAGED/REPLACEMENT PARTS
Please visit www.coreproducts.co.uk/parts
Batch Number:
PLEASE RETAIN THIS LEAFLET ALONG WITH YOUR DELIVERY NOTE/RECEIPT FOR FUTURE REFERENCE
DK221
90 min
A = x38
Dowel
B = x36
40mm Screw
C = x20
25mm screw
D = x50
Nail
E = x4
Mag. Catch
F = x20
20mm screw
M = x4
K = x2
H = x4
G = x2
30mm Bolt
Knob
18mm Bolt
Handle

1
A = x4
Dowel
C = x4
25mm Screw
2
A = x12
Dowel
3
B = x6
40mm Screw
4
Tip: during assembly
place unit onto a work
surface with a clean cover
B = x6
40mm Screw

5
Tip: Place top of unit over the edge
of the work surface to ensure the
top does not mark during assembly
D = x20
Nail
6
H = x4
18mm Bolt
G = x2
Handle
C = x16
25mm Screw
7
A = x20
Dowel

8
9
Tip: during assembly
place unit onto a work
surface with a clean cover
B = x6
B = x8
40mm Screw
40mm Screw
10
11
B = x6
B = x4
40mm Screw
40mm Screw

12
13
Tip: during assembly
place unit onto a work
surface with a clean cover
D = x30
F = x8
E = x4
Nail
20mm Screw
Mag. Catch
14
15
Tip: insert dowels from the inside
of the drawers, pushing through
so they sit level with the inside of
F = x12
K = x2
M = X2
A = x2
the drawer side.
20mm Screw
Knob
30mm Bolt
Dowel

WARNING! TIPPING HAZARD – Unanchored furniture can tip over
WARNING: CHECK FOR HIDDEN PIPES AND CABLES BEFORE DRILLING.
IMPORTANT: IF YOUR WALLS ARE NOT SOLID LIKE BRICK OR STONE, YOU WILL REQUIRE SPECIALIST FITTINGS (NOT SUPPLIED)
- Attach fixing strip to the wall using the 25mm screw + washer and securely tighten;
- Pre-drill small pilot hole on the back edge of the furniture top using a 2mm drill bit. Attach the other end of the fixing strip
to the back edge of the furniture top using the 15mm screw + washer and securely tighten.
- Place fixing strip against the wall and mark position for drilling hole.
- Drill hole in your wall to a depth of 30mm using a 6mm drill bit. If the surface of your wall is soft and crumbly,
we would advise you to use a 5mm drill bit for a tighter fit.
- Insert plug into hole with end flush to the wall surface;
Z = x2
Washer
Y = x1
Wall Tie
W = x1
Wall Plug
16
C = x1
25mm Screw
X = x1
15mm Screw