Core Products MANHATTAN MN925 User manual

Height: 1798 mm
Width: 529 mm
Depth: 400 mm
120 min
BATCH NUMBER
MANHATTAN HIGH BAR CABINET
REF. MN925
BEFORE YOU START ASSEMBLY
Please check that you have all the
correct parts and fittings as detailed.
In the unlikely event that you require to
order spare parts or fittings please refer
to your delivery note for details of how
to order using our Parts website.
www.coreproducts.co.uk/parts
Customer help line: 01738 630555
We recommend that you build your
furniture on top of a soft clean cover to
ensure the unit does not get marked or
damaged during assembly.
PLEASE RETAIN THIS INSTRUCTION LEAFLET FOR FUTURE REFERENCE.
Thank you for choosing this furniture.
Always lift your furniture when moving as dragging may cause damage to your furniture or flooring.
Do not sit or stand on your furniture.
a label adhesive removal liquid available from most DIY or hardware stores.
13/10/2020

ASSEMBLY HARDWARE
Page 2
ASSEMBLY PARTS MAX SUGGESTED LOADS
A - x1
B - x1
C - x1
D - x1
E - x1
F - x1
G - x3
H - x1
I - x1
J - x1
K - x1
L - x1
M - x1
N - x2
O - x2
P - x2
Shelf Support
x2
x2
Roll Over Kit
(Includes screws)
Flat Head Screw
x19
D
M
E
O
O
B
G
G
G
C
H
L
K
F
I
P
P
J
N
N
A
10kg
10kg
8kg
8kg
1kg 1kg 1kg 1kg
1kg 1kg 1kg 1kg
x64
Dowel Minifix Bolt
x32 x32
Minifix Cams Cover Caps
x10
Cover Caps
x24
(Colour 1) (Colour 2)
x4
Steel Leg
End Panel Hinge
(EPH)
(Includes screws)
x4
Wine Glass
Rack
x1
Tube
x1

1
3
2
M
D
D
M
2
1
Rotate 180°
Gently hit
to adjust.
12
Gently hit to adjust.
Repeat this in the
following steps.
Gently hit to adjust.
Repeat this in the
following steps.
Turn minifix cams to
the right to tighten
Page 3

4
6
5
E
E
E
D
M
Rotate
Rotate to tighten
Gently hit
to adjust.
Page 4

7
9
8
Gx3
H
H
G
G
G
Slide
Page 5

10
12
11
F
F
GGGH
F
G
HG
G
M
D
E
Gently hit
to adjust.
Gently hit
to adjust.
Page 6

13
15
14
I
Nx2
NI
Rotate to tighten
Gently hit
to adjust.
Page 7

16
18
17
J
B
B
D
M
E
I
N
N
JFH
G
G
G
B
I
F
Rotate to tighten
Gently hit
to adjust.
End Panel Hinge
(EPH)
Page 8
Tube

19
21
20
MD
E
I
N
N
JO
O
F
B
H
MD
O
O
B
J
N
N
IFHE
C
C
Slide into
the cabinet
Rotate
Rotate to tighten
Gently hit
to adjust.
Page 9
End Panel Hinge
(EPH)

22
24
23
D
M
O
O
N
NC
J
B
P
P
A
A
Slide into
the cabinet
Rotate
A
Page 10

25
26
P
P
MD
O
O
C
N
N
A
E
D
C
B
I
F
H
G
G
G
J
A
P
K
L
Gently hit
to adjust.
Rotate to tighten
DOOR INSTALLATION
KB
CAREFULLY FLIP THE FURNITURE !
Page 11

27
E
D
C
B
I
F
H
G
G
G
KL
After you finish the
adjustment of the cams,
cover them with the
cover caps. AAfter you finish
assembling the cabinet,
take off the adhesive
letters.
-WARNING! TIPPING HAZARD – Unanchored
furniture can tip over
-WARNING: CHECK FOR HIDDEN PIPES AND
CABLES BEFORE DRILLING.
-IMPORTANT: IF YOUR WALLS ARE NOT SOLID
LIKE BRICK OR STONE, YOU WILL REQUIRE
SPECIALIST FITTINGS (NOT SUPPLIED)
-Pre-drill small pilot hole on the back edge of the
furniture top using a 2mm drill bit. Attach the other
end of the fixing strip to the back edge of the
furniture top using the 15mm screw + washer and
securely tighten.
-Place fixing strip against the wall and mark position
for drilling hole.
-Drill hole in your wall to a depth of 30mm using a
6mm drill bit. If the surface of your wall is soft and
crumbly, we would advise you to use a 5mm drill bit
for a tighter fit.
-Insert plug into hole with end flush to the wall
surface.
-Attach fixing strip to the wall using the 25mm
screw + washer and securely tighten.
For the user safety, it is recommended
to anchor the cabinet to the wall.
Page 12