Cornelius ED-300 User manual

ED300 Ice Maker Adapter Lid Installation Instructions
© 2016, Cornelius Inc. - 1 - Publication Number: 08027TEINS
INSTALLATION INSTRUCTIONS
ED300 ICE MAKER ADAPTER LID FOR KITS P/N 08027TE AND
P/N 08030TE
!
WARNING:
Disconnect power to the unit before installing the adaptor following all lockout/tag out procedures established by the
user. Verify that all the power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
All of the attachment screws and plates must be installed as directed in this manual.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
All ice baffle plates and bin stats, if included or recommended in this kit, must be installed as directed in this manual or
the equipment manufacturer’s instructions.
Failure to comply could result in serious injury, death or damage to the equipment.
!
WARNING:
The dispenser must be secured with 3/8 X16 bolts (6) to the counter before installing the ice maker adapter kit. Refer
to the installation manual and for the counter mounting template.
NOTE: Adjust the automatic agitation timer located in the dispenser’s electrical control box to 5 sec-
onds on, 20 minutes off. Access to the timer is provided by removing the merchandiser/upper
front panel.
1. Remove the top plastic bin covers (2) from the dispenser.
2. Place the Adapter lid assembly (item 1) on top of the dispenser and position it flush with the rear and sides
of the dispenser as shown in Figure 1.
3. Install the ice baffle on the lid assembly as shown in .
Table 1. Loose Shipped Parts
Item No. Part No. Name Qty.
1 29505 Lid Assembly 1
2 22127 Ice Maker Mounting Bracket 2
3 50904 RTV, 3 oz. Tube 1
4620064177 Lid & Lanyard assembly ED300 Black (08027TE) 1
620065192 Lid & Lanyard assembly ED300 Grey (08030TE)
5 91957 Label, “Disconnect Power Before Cleaning” 1
6 620042919 ED300 Ice Baffle 1
7 620701601 Screw TF SM 10-16 PNPH 16SS 12
8 620701902 #8-32 Nylon Acorn Nut 4
9 620701901 Sealing Washer 4
10 620701903 #8 Nylon Washer 4
11 08027TEINS Installation Instructions 1
12 43164 Screw MA 08-32 TRPH 10 SS 2
13 70100 Nut HEX 08-32 SS Nylok 2
Revision Date: July 05, 2016 www.cornelius.com Revision: A

ED300 Ice Maker Adapter Lid Installation Instructions
Publication Number: 08027TEINS - 2 - © 2016, Cornelius Inc.
IMPORTANT: The baffle prevents ice from over-filling the manual fill area during agitation/
dispensing with a full storage bin and forcing the manual fill cover off.
4. Using the slotted holes in the lid as a template, drill (4) 0.147” diameter holes (#26 drill) at the bottom of the
slots (see Figure 1. Detail A). BE CAREFULLY NOT TO DRILL INTO THE ICE STORAGE BIN. Secure the
lid to the dispenser with (4) #10 sheet metal screws.
5. Seal the ice maker to the dispenser lid as follows (See Figure 1.).
A. Run beads of RTV around the opening in the lid and inside of the perimeter of the ice maker outline so
that the ice maker will set on the RTV.
B. Set the ice maker onto the lid and position it as shown in Figure 1.
C. Wipe away the excess RTV.
6. Drill .147” diameter holes into the ice maker cabinet and the dispenser lid using the ice maker mounting
brackets as templates. USE CAUTION SO AS NOT TO DRILL INTO ANY ICE MAKER COMPONENTS
(CONDENSER, TUBING, ETC.). Secure the brackets using the #10 sheet metal screws provided.
7. Follow the ice maker manufacturers instruction to complete the installation of the ice maker including the bin
thermostat if so equipped or required.
CAUTION:
!
The bin thermostat location must not interfere with agitator rotation.
8. Locate the cleaning caution label (item 5) on the manual ice fill cover (item 4) as shown in Figure 1. Place the
manual fill cover in position over the flange on the lid assembly and the front access hopper opening.
Figure 1. Dispenser
5
4

ED300 Ice Maker Adapter Lid Installation Instructions
© 2016, Cornelius Inc. - 3 - Publication Number: 08027TEINS
Figure 2. ED300 Baffle Kit
Figure 3. Reference Sheetmetal Cover Opening Dimensions for Mounting Icemaker.
4 PLC. ICEMAKER SHOWN
FOR REFERENCE
ONLY
4 PLC.
BAFFLE
(ITEM 6)
SHOWN
IN PLACE
4 PLC.
1
9
8
6
10