COVERPRO 59699 Assembly instructions

Vehicle not included.
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
WARNING! TO PREVENT SERIOUS
INJURY: Do not start or operate any internal
combustion engine inside or near Shed.
Fits Portable Garage
UPC 193175335340 and
792363628594 (UPC
found on label sewn
inside roof cover)
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual (or month and year of purchase if product has no number). Keep this manual and the
receipt in a safe and dry place for future reference. 23a
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2022 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Table of Contents
Important Safety Information ...................... 3
Assembly.................................................... 4
Maintenance.............................................. 10
Parts List and Diagram.............................. 11
Warranty .................................................... 12
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
safety goggles with side shields.
Read the manual before
assembly and/or use.
WARNING marking concerning
Risk of Head Injury. Wear hard hat
during assembly and service.
WARNING marking concerning Risk
of Hand Injury. Wear heavy-duty work
gloves during assembly and service.
Page 2 For technical questions, please call 1-888-866-5797. Item 59699
SAFETY OPERATION MAINTENANCESETUP
Page 2 For technical questions, please call 1-888-866-5797. Item 59699

IMPORTANT SAFETY INFORMATION
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in serious injury.
Save all warnings and instructions for future reference.
The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible
conditions and situations that may occur. It must be understood by the operator that common sense
and caution are factors which cannot be built into this product, but must be supplied by the operator.
Assembly Precautions
1. Do not assemble in windy conditions.
2. Assemble and install only on
flat, level, hard surface.
3. Assemble and anchor only according to
these instructions. Improper assembly or
inadequate anchoring can create hazards.
4. Check for utility lines, tree branches and
other structures before assembling.
5. Verify that installation surface has no
hidden utility lines before anchoring.
6. Wear ANSI-approved safety goggles,
heavy-duty work gloves and hard hat
during assembly and service.
7. Keep assembly area clean and well lit.
8. Keep bystanders out of the area during assembly.
9. Do not assemble when tired or when under
the influence of drugs or medication.
10. Product capabilities apply to properly and
completely assembled product only.
Use Precautions
1. CARBON MONOXIDE HAZARD
Using an engine inside Shed
CAN KILL YOU IN MINUTES.
Engine exhaust contains
carbon monoxide. This is a poison you cannot see
or smell. NEVER use an engine inside Shed,
EVEN IF cover is open. Only use an engine
OUTSIDE and far away from Shed.
2. DO NOT USE IN HIGH WIND. Remove cover
if harsh weather or heavy rain threatens.
3. For temporary use only.
Do not use for long-term shelter.
4. Do not use as tent. Does not meet tent
flammability standards. Do not use grill, heater,
or ignition sources inside or near cover.
5. Do not allow snow, rainwater or debris
to accumulate or pool on cover.
6. Do not hang objects from any part of the Garage.
7. This product is not a toy. Do not allow
children to play with or near this item.
8. Use as intended only.
9. Inspect regularly, tighten all loose hardware
and loose straps, and secure all loosened
anchors. If any parts are damaged, bent, or
stretched, they must be replaced. Hardware
may loosen during normal operation stresses.
Loose hardware or damaged/altered parts will
compromise the structural integrity of this product.
10. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
SAVE THESE INSTRUCTIONS.
Page 3For technical questions, please call 1-888-866-5797.Item 59699
SAFETYOPERATIONMAINTENANCE SETUP
Page 3For technical questions, please call 1-888-866-5797.Item 59699

Before Setup
Compatibility
1. This product is only compatible with
UPC 193175335340 and 792363628594.
2. To find UPC on original Portable Garage,
locate sewn in label on inside of Roof Cover.
WARNING
Topreventseriousinjury,property damage, and collapse:
1. CARBONMONOXIDEHAZARD.Using an engine inside Shed CAN
KILLYOUINMINUTES. Engine exhaust contains carbon monoxide.
Thisisapoisonyou cannot see or smell. NEVERuseanengineinside
theShed,EVENIFcover is open. OnlyuseanengineOUTSIDE and
farawayfromShed.
2.DONOT USE IN HIGH WIND. Removecoverif
harshweatherorheavyrain threatens.
3.Fortemporary use only. Donotuseforlong term shelter.
4.Donot use as a tent. Doesnotmeettentflammability standards. Do
notusegrill,heater,or ignition sources inside or near cover.
5.Donot allow snow, rainwater, or debris to accumulate or pool on shelter.
6.Donot hang objects from any part of the Garage.
7.Anchorsecurely to flat, level, solid surface able to support
shelterandvehicleaccordingto manual instructions.
8.Inspectbefore assembly and every use;
donotassembleoruse if parts loose or damaged.
9.WearANSI-approved safety goggles, heavy-duty work gloves,
andhardhatduringassembly and service.
10.Readmanualbeforeassembly and/or use.
62860
20j
Serial:
UPC193175335340
UPC Label
3. UPC is located at the bottom of the label.
WARNING
To prevent serious injury, property damage, and collapse:
1. CARBON MONOXIDE HAZARD. Using an engine inside Shed CAN
KILL YOU IN MINUTES. Engine exhaust contains carbon monoxide.
This is a poison you cannot see or smell. NEVER use an engine inside
the Shed, EVEN IF cover is open. Only use an engine OUTSIDE and
far away from Shed.
2. DO NOT USE IN HIGH WIND. Remove cover if
harsh weather or heavy rain threatens.
3. For temporary use only. Do not use for long term shelter.
4. Do not use as a tent. Does not meet tent flammability standards. Do
not use grill, heater, or ignition sources inside or near cover.
5. Do not allow snow, rainwater, or debris to accumulate or pool on shelter.
6. Do not hang objects from any part of the Garage.
7. Anchor securely to flat, level, solid surface able to support
shelter and vehicle according to manual instructions.
8. Inspect before assembly and every use;
do not assemble or use if parts loose or damaged.
9. Wear ANSI-approved safety goggles, heavy-duty work gloves,
and hard hat during assembly and service.
10. Read manual before assembly and/or use.
62860 20j Serial:
UPC 193175335340
UPC
Assembly
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Note: For additional information regarding the parts listed in the following
pages, refer to Parts List and Diagram on page 11.
TO PREVENT SERIOUS INJURY:
Do not leave this product partially assembled. Assemble this product completely at one time.
Note: At least 3 workers are required for assembly. Before starting assembly, review the instructions and make
sure there is enough time and the proper tools available to properly assemble.
Finger tighten all connections until assembly is done. Assemble on a flat, level surface.
Removing Door/Back Cover
1. Referring to Releasing Ratchet Tie-Downs on page 6, loosen but do not remove the two
Ratchet Tie-Downs that secure the Roof Cover to the Garage. The Roof Cover flaps wrap around
the Door/Back Cover. Loosen the Roof Cover just enough to access the Door/Back Cover.
Ratchet
Tie-Down
Roof Cover
Page 4 For technical questions, please call 1-888-866-5797. Item 59699
SAFETY OPERATION MAINTENANCESETUP

2. Remove the two Ratchet Tie-downs at the Corner Legs that secure the Door/Back Cover
to the Garage. Save the Ratchet Tie-downs for the new Cover.
Ratchet
Tie-down
Bottom corner
of Garage
Corner Leg
3. From inside the Garage, disconnect the Rails from the frame’s 3-Way Ridge and Side Connectors.
Inside View
3-Way Ridge Connector
Rafter
Rail
3
Rail
3-Way Side
Connector
Rail
Zipper
Rail Rafter
Zipper Rail
Outside View
Note: Roof Cover not shown to provide a clear view of frame construction.
4. Remove Door/Back Cover from frame’s Rafter and side tubes.
5. Install new Cover by referring to Door and Back Cover Installation on page 7.
Removing Roof
1. Referring to Releasing Ratchet Tie-Downs on
page 6, disconnect and remove the four Ratchet
Tie-downs at the Corner Legs that secure the Roof
Cover to the Garage.
Save the Ratchet Tie-downs
for the new Roof Cover.
Ratchet
Tie-Down
Roof Cover
Note: Do not remove the Door/Back Cover.
2. Attach a rope (sold separately) to each
corner as shown below. Throw ropes over
the roof to the other side then pull ropes to
remove the Roof Cover from the frame.
Remove the two corner Ropes and
save them for the new Roof Cover.
Ropes
3. Install new Roof Cover by referring to Roof
Cover Installation on page 8.
Page 5For technical questions, please call 1-888-866-5797.Item 59699
SAFETYOPERATIONMAINTENANCE SETUP

Securing Ratchet Tie-Downs
Note: Use these instructions for installing
Door, Back, and Roof Cover.
1. Thread the strap through the Ratchet’s (8)
spindle as far as it will go.
2. Insert the S-hook of the Ratchet into
the hole in the Corner Leg (6).
3. Lift and lower the Ratchet’s handle to wind
and tighten the strap onto the spindle.
NOTICE: Excessive tightening will damage
straps, Covers, and Corner Legs.
Releasing Ratchet Tie-Downs
1. Depress the spring-loaded bar on the handle.
2. Open Ratchet handle completely.
3. Unwind the strap.
Page 6 For technical questions, please call 1-888-866-5797. Item 59699
SAFETY OPERATION MAINTENANCESETUP

Door and Back Cover Installation
Note: When installing Door/Back Cover, ensure that pre-installed straps are not pulled out of the Hem.
Note: Roof Cover not shown on illustrations to provide a clear view of installation.
1. Position the Door Cover near where you want the front of the Portable Garage,
and turn it so that the zipper faces the outside of the Garage, and the warning tag
faces inside. The Back Cover attaches to the other end of the Garage.
2. From inside, with the Rails disconnected, place the Door/Back Cover
gaps at the frame’s 3-Way Connectors as shown below.
3. Insert the frame’s Rafter and side tubes into the pockets of the Door/Back Cover as shown below.
DO NOT ATTEMPT TO INSERT ANY FRAMEWORK TUBING INTO THE HEM ON THE COVER FLAPS.
4. Reconnect the Rails and side tubes securely to the 3-Way Connectors.
Note the strap is positioned inside the frame.
3-Way Side
Connector
Rail Place strap
and flaps
inside frame.
Zipper
Rail
Rafter
Rail
Rail
Hem on
Cover flap
Rafter
3-Way Ridge
Connector
Rail
Pocket
3-Way Side
Connector
Inside View Outside View
Zipper
5. Use the two saved Ratchet Tie-Downs to attach the Door/Back Cover to the two Corner Legs.
Refer to Securing Ratchet Tie-Downs on page 6.
Ratchet Tie-Down
Bottom corner
of Garage
6. Wrap Roof Cover flaps around Door/Back Cover. Tighten the four Ratchet Tie-Downs
that secure the Roof Cover to the Garage frame.
Page 7For technical questions, please call 1-888-866-5797.Item 59699
SAFETYOPERATIONMAINTENANCE SETUP

Roof Cover Installation
1. Lay the Roof Cover on the ground, next to the
frame, so that the inside pockets face up.
Note: Door and Back Covers not shown in illustration
below to provide a clear view of frame assembly.
2. Remove two Bottom Rails by loosening the
Bolt and Nut connecting the 4-Way Center Rail
and 3-Way End Rail Clamps.
Bottom Rails
M8 Nut
4-Way Center
Rail Clamp
M8 x 50 Hex Head Bolt
3-Way End
Rail Clamp
M8 Nut
M8 x 50 Hex Head Bolt
3. Slide the two Bottom Rails into the middle openings
of the bottom inside pockets of the Roof Cover.
4. Tie saved ropes to each Bottom Rail
as shown below.
Roof Cover
Bottom Rails
Pocket
Rope
Rope
Bottom Rail
Page 8 For technical questions, please call 1-888-866-5797. Item 59699
SAFETY OPERATION MAINTENANCESETUP

5. Throw the ropes over the top of
the frame to the other side.
6. From the other side, pull the ropes to properly
position the Roof Cover over the frame.
7. Remove the ropes and Bottom Rails.
8. Reconnect the Bottom Rails to the frame.
Tighten the 4-Way Center Rail and
3-Way End Rail Clamps’ Bolt and Nut
to secure the Bottom Rails.
9. Using the four saved Ratchet Tie-Downs,
secure all four corners of the Roof Cover
to the outside of the Corner Legs. Refer to
Securing Ratchet Tie-Downs on page 6.
Note: The Roof Cover flaps cover the Door/Back Cover.
Ratchet
Tie-Down
Roof Cover
Page 9For technical questions, please call 1-888-866-5797.Item 59699
SAFETYOPERATIONMAINTENANCE SETUP

Maintenance
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM PRODUCT FAILURE:
Do not use damaged products. If damage is noted, have the problem corrected before further use.
MONTHLY, inspect the general condition of the Portable Garage. Check for:
• loose ratchet tie downs, anchors, tube connections, and rail clamps (tighten as needed),
• torn or frayed covers, straps, or cables,
• cracked, bent, or broken parts, and
• any other condition that may affect its safe operation.
Cleaning
1. Immediately remove any accumulated
debris from the cover with a broom, mop,
or other soft-sided instrument from the
outside. DO NOT use sharp instruments.
2. PERIODICALLY, clean cover with mild
soap and water. DO NOT use bleach
or harsh abrasive products.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts. Specify UPC 193175478795 when ordering parts.
Page 10 For technical questions, please call 1-888-866-5797. Item 59699
SAFETY OPERATION MAINTENANCESETUP

Parts List and Diagram
Note: Individual part illustrations not to scale.
Part Description Illustration Qty
1 Roof Cover 1
2 Door Cover 1
3 Back Cover 1
1
2
3
Page 11For technical questions, please call 1-888-866-5797.Item 59699
SAFETYOPERATIONMAINTENANCE SETUP

26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.