CPI STEMSHINE User manual

STEMSHINE – THE GLASS POLISHER
Model GP8
OPERATING INSTRUCTIONS
Sales & Service
2871 Brighton Road
Oakville, ON L6H 6C9
[phone]
www.cpishine.com
IMPORTANT
FILL OUT and RETURN
ENCLOSED PRODUCT REGISTRATION
WARRANTY CARD
Rev: Jan 2015

Campus Products, Inc. (“CPI”) warrants to the original purchaser that any original part that is found to be defective
in material or workmanship will, at our option, subject to provisions hereinafter stated, be replaced with a new or
rebuilt part.
The labor warranty remains in effect one (1) year from installation or fifteen (15) months from the shipping date,
whichever occurs first. CPI will bear normal labor charges performed during standard business hours not subject
to overtime, holiday rates or any additional fees.
Failure to replace the manufacturer approved drying/polishing granulate on a timely and regular basis (every 4
months) will lead to the automatic forfeiture of warranty rights and the Manufacturer will not be obliged to
perform any repairs and/or replacements.
The parts warranty remains in effect one (1) year from installation or (15) months from the shipping date, which-
ever occurs first.
This warranty does not apply to:
1. Replacement of brushes, brush stems or brush ends due to damage or wear of any kind.
2. Replacement of granulate necessitated by day to day use.
3. Replacement of heating elements necessitated by day to day use.
4. Equipment damage caused by accident, shipping, improper installation or alteration or by expired granulate.
5. Original or ongoing calibration.
6. Equipment used under conditions of abuse, misuse, carelessness or abnormal condition including equipment
subjected to harsh or inappropriate chemicals, poor water quality or equipment with missing or altered serial
numbers.
7. Equipment modified in any manner from original model, substitution of parts other than factory authorized
parts, removal or any parts including legs, or addition of any parts.
8. Any losses or damage resulting from malfunction, including loss of product or consequential or incidental
damages of any kind.
This warranty is exclusive and is in lieu of all other warranties, expressed or implied, including the implied
warranties of merchantability and fitness for purpose. In no event shall the Company be liable for loss of use,
loss of revenue, or loss of product or profit, or for indirect or consequential damages. This warranty is in lieu
of all other warranties expressed or implied and CPI neither assumes or authorizes any persons to assume for it
any other obligation or liability in connection with CPI equipment.
ORIGINAL EQUIPMENT
LIMITED WARRANTY

Page - 4 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
TABLE OF CONTENTS
OPERATING INSTRUCTIONS FOR STEMSHINE – THE GLASS POLISHER........................5
WHAT THE MACHINE IS DESIGNED TO DO ...................................................................................................... 5
HOW THE MACHINE WORKS .............................................................................................................................. 6
TECHNICAL FEATURES ...................................................................................................................................... 7
INSTALLATION INSTRUCTIONS.............................................................................................8
UNPACKING THE MACHINE ................................................................................................................................ 8
POSITIONING THE GLASS POLISHER ............................................................................................................... 8
ASSEMBLING THE BRUSHES ............................................................................................................................. 8
ELECTRICAL CONNECTION ............................................................................................................................... 9
STARTING THE MACHINE FOR THE FIRST TIME ............................................................................................. 9
HOW TO USE THE GLASS DRIER.........................................................................................10
DAILY OPERATION: ........................................................................................................................................... 10
DAILY CLEANING ............................................................................................................................................... 12
WEEKLY CLEANING .......................................................................................................................................... 13
MAINTENANCE INSTRUCTIONS...........................................................................................14
INTRODUCTION ................................................................................................................................................. 14
ORDINARY MAINTENANCE ............................................................................................................................... 15
MONTHLY CLEANING ........................................................................................................................................ 15
BRUSH CHANGEOUT PROCEDURES : ........................................................................................................... 16
REPLACE A FULL SET OF BRUSHES .......................................................................................................... 17
REPLACE THE GREEN BRUSH TIP ............................................................................................................. 17
REPLACE THE RED OR YELLOW BRUSH TIP ............................................................................................ 17
EXTRAORDINARY MAINTENANCE................................................................................................................... 19
GP8 EXPLODED DIAGRAM ………………………………………………………………………20
SPARE PART CODES………………………………………………………………………………………………….22
QUICK START INSTRUCTIONS……………………………………………………………………24
Rev: Jan 2015

Page - 5 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
OPERATING INSTRUCTIONS FOR STEMSHINE – THE GLASS POLISHER
WHAT THE MACHINE IS DESIGNED TO DO
Stemshine – The Glass Polisher was designed with the restaurant operator in mind. Eight high
spinning soft-polishing brushes, aided by a heated fan, assists the operator in producing shiny,
luminous stemware. Easily capable of drying and polishing six to eight times the human
equivalent, “Stemshine” provides labour savings in addition to high quality results.
The purpose of this document is to provide you with the necessary operating instructions to get
the most out of your “Stemshine” glass polisher.

Page - 6 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
HOW THE MACHINE WORKS
Stemshine is available in one model size: GP8.
The unit is comprised of a polished stainless steel, durable frame; a calrod heat element; a
high speed powerful fan to aid in the drying process and synthetic, easy to clean, brushes.
With a one touch On/Off control button, this lightweight unit is simple to use with the versatility
to be moved anywhere in your facility.
All that is required of the operator is to remove the glasses, clean and wet, from the glass
washer. Place the glasses, one by one, on the warm, dry brushes for drying and polishing and
then remove them, ready for immediate use.

Page - 7 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
TECHNICAL FEATURES
Model GP8
Amps 13
Watts 1500
Dimensions (W X D X H) 15 X 18 X 24
Volts 110; 60hZ
Ship Wt. (lbs.) 60
Noise Level 60 dbA
68 dbC

Page - 8 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
INSTALLATION INSTRUCTIONS
UNPACKING THE MACHINE
The machine is delivered packed in a cardboard box containing compressed
polystyrene. Dispose of the packing material according to the requirements of the local
recycling laws.
Verify the machine's integrity and in particular the electric cables. If in doubt, ask a technician
to check before proceeding with installation.
POSITIONING THE GLASS POLISHER
 The machine does not require anchoring - but must be level on whatever surface it is
sitting on. This may require the adjustment of the nut located at the base of each leg.
 Make sure that no objects (cloths, etc.) are placed under the glass drier so as not to
obstruct air flow.
 Ensure the glass drier is not placed close to any taps and/or water connections.
ASSEMBLING THE BRUSHES
Each glass polisher is packaged with 8 brushes and these brushes are colour coded (red,
yellow and green) at the bottom of the brush base. On the top of each support (B) is a coloured
dot corresponding to the brush colours (red, yellow and green).
Place each brush on top of support (B) (matching the colours) and slide the brush down the
support. Ensure that slot (A) is connected by slightly rotating the brush in a clockwise
direction. If the brush is not properly fixed on the support, it will not rotate once the machine is
switched on.

Page - 9 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
To verify correct placement of the brushes, try to rotate them clockwise and then pull lightly
upwards: if the brush does not come off the support, placement is correct.
ELECTRICAL CONNECTION
First, verify that the power supplied corresponds to the machine's requirement by checking the
data on the label attached on the right hand side. Check that the electric plant and the socket
are suitable to supply a domestic appliance with a power of 1.8 Kw. If the socket does not
correspond to the plug, ask an electrician to change it. Do not employ an
adaptor as this may cause overheating and burning.
Never use an extension cord to reach the electric cable to the outlet. If the cable is not long
enough, reposition the glass polisher nearer to the outlet or have an electrician change out the
cable for a longer cable.
Ensure the cable does not rest on sharp edges and is not compressed or bent by other
objects.
STARTING THE MACHINE FOR THE FIRST TIME
This is the same procedure that you would engage for all subsequent start ups of the machine.
 Ensure the glass drier is placed in a location where the operator will find it comfortable
to operate.
 Ensure nothing is placed under the glass polisher that could obstruct air flow – i.e.
cloths
 Insert the plug into the nearest socket.
 Press the “Power” button located on t he front of the dryer to start up
the machine.
a. The button will illuminate indicating there is power to the unit.
b. The brushes will begin to rotate
c. The calrod element heats up
d. The fan will begin to circulate increasingly warm air around
the brushes.
WARNING: Ensure that no objects get caught in the rotation of the brushes.
Allow the brushes to heat up for approximately 10 – 15 minutes before
using the GP8 to dry glasses.

Page - 10 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
HOW TO USE THE GLASS DRIER
The purpose of your “Stemshine” unit is to provide your clients with luminous, spot-free
stemware. It accomplishes this feat through the synthetic, easy to clean heated
brushes.
DAILY OPERATION:
 Ensure the glass drier is placed in a location where the operator will find it
comfortable to operate.
 Insert the plug into the nearest socket.
 Press the “Power” button located on the front of the dryer to start
up the machine.
a. The button will illuminate indicating there is power to the
unit.
b. The brushes will begin to rotate
c. The calrod element heats up
d. The fan will begin to circulate increasingly warm air around
the brushes.
Before using the glass polisher, warm the brushes for at least 10 – 15 minutes.
WARNING: Ensure that no objects get caught in the rotation of the brushes.
 Remove clean, wet glasses directly from the glass washer
Wear the specialized CPI “dimpled” polishing
gloves. Lift the glass(es) and place on one of the
two middle brushes. Form a circle with your
thumb and fore-finger and encircle the stem of the
glass – the “OK” grip. This “OK” grip should only
be used to balance the glass -- the glass should
rotate slightly on the brushes.
Place the glass over one of the MIDDLE brushes
and gently guide the stem of the glass. Gently
rock the glass back and forth, side to side, for
approximately 3 to 4 seconds.

Page - 11 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
IT IS NOT NECESSARY TO APPLY PRESSURE WHEN HOLDING THE STEMWARE
AGAINST THE BRUSHES
PLEASE NOTE: the glass drier does not clean stemware, or remove any stains on
the glasses.
At the end of the day or once all stemware has been dried and polished, allow the brushes to
dry out by running the machine for an additional 15 minutes prior to turning off the machine.
Lift the glass and place it on one of the
four outside brushes. Quickly repeat the
rocking action for another 3 to 4 seconds.
Finally, pick up the glass using the “OK”
grip and then pinch the stem of the glass,
again
Place the base of the glass against the front
three brushes to dry/polish the top and bottom
of the base. Using the pinching grip place the
glass in the proper storage vessel.

Page - 12 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
DAILY CLEANING
The glass polisher needs to be cleaned on a daily basis.
1. Turn the machine off and unplug it.
2. Remove the brushes as follows:
3. Place the brushes evenly on the flat rack or dish rack of your dishwasher (either laying
down or standing up). Ensure they do not overlap one another.
4. Run them through a regular wash cycle in your high temperature dishwasher - TWICE.
5. After the second regular wash cycle is complete, rinse the brushes with plenty of fresh
water to remove soap and chemical that is applied during the wash cycle.
6. Allow the brushes to drip dry overnight on the rack.
7. In the morning, place the brushes back onto the coloured coded spindles matching the
colours of the brush to the colour on the spindle. Turn the brush in a clockwise direction to
lock in place. Be sure that the brushes are correctly inserted onto the spindles.
8. After all brushes are placed on the spindles / support, plug in the machine and turn the
power on. Run for approx. 20-30 minutes or until dry.
WARNING: Do not place the glass drier in a container wi th water because it contains
electrical parts that could be damaged and cause electric shock to the operator once it is
switched back on.
To remove the brush from the support, rotate the brush in a
counter clockwise direction while gently pulling it upwards.
Remove the brush completely by slipping it off its support.

Page - 13 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
WEEKLY CLEANING
Turn the machine off and unplug it.
Remove the brushes as follows:
To clean the glass polisher, cool down the polisher and then remove the brushes. The
brushes must be hand washed. Place the brushes in a tub of warm water (max 30°C) using a
non-foaming, neutral detergent. Then wipe down the exterior stainless steel casing using a
damp cloth.
WARNING: do not place the glass drier in a container wi th water because it contains
electrical parts that could be damaged and cause electric shock to the operator once it is
switched back on.
Remove the brushes from the warm water and allow them to drip dry overnight before
replacing the brushes onto the glass polishing machine. To replace the brushes, ensure
the connecting slot (A) – shown on page 8, is inserted on the top of support (B) - matching the
colour of the brush to the support. If the brush is not properly fixed on the support, it will not
rotate once the machine is switched back on. To verify this, once the brush has been replaced
try to rotate it clockwise and then pull it gently upwards: if the brush does not come off it has
been placed correctly.
Then turn the machine back on and run for approx. 15 minutes to complete the drying of the
brushes.
To remove the brush from the support, rotate the brush in a
counter clockwise direction while gently pulling it upwards.
Remove the brush completely by slipping it off its support.

Page - 14 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
MAINTENANCE INSTRUCTIONS
INTRODUCTION
Installing and starting the glass dryer with care ensures long lasting operation with no
inconvenience to the user. The guiding principle that the user should follow, and that Campus
Products Inc. would like to stress, is that the machine requires frequent cleaning and routine
maintenance, a list of operations are indicated below.
During maintenance, cleaning products and lubricants will be employed, therefore it is
necessary to remember the following:
"""""
There are two stages of maintenance. ORDINARY MAINTENANCE: can be carried out by the
operator and EXTRAORDINARY MAINTENANCE: must be carried out o nly by a qualified
technician.
Lubricants. solvents and detergents are toxic substances. harmful to
health:.
 they can cause irritation if they come into contact with the skin,
 they can cause serious intoxication if inhaled
 or in some cases, can cause death if swallowed.
 Handle with care, wearing the appropriate protection as provided
by law
 Do not dispose of these products into the environment; dispose of
waste conforming to the local law requirements concerning toxic
waste.

Page - 15 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
ORDINARY MAINTENANCE
To perform any maintenance on Stem shine – the Glass Polisher, the machine must be turned off and
disconnected from the socket. The appropriate t ooling must be used t ogether with indiv idual
protection, according to the applicable laws.
Ordinary maintenance consists of cleaning the glass polisher on a regular basis with detergents;
vacuuming the interior chamber of the machine to remove lint and dust; and replacing the brushes on
an annual basis. DO NOT IMMERSE THE MACHINE IN WATER. The control panel is particularly
sensitive to humidity: if it gets inside the panel, it can short circuit the electronic board.
The electric cable must be chec ked meticulously at least once a week, using an extra lamp, to make
sure that it has no scratches (even small ones) and does not present irregularities.
MONTHLY CLEANING
On a monthly basis, the GP8 side panel should be removed and the interior of the machine should be
vacuumed clean.
1. Ensure the unit is turned off and disconnected from the power.
2. Using a slot head screw driver remove the four screws that attach the side panel to the
machine.
3. Using a shop vac, vacuum the interior of the machine to remove any dust or lint from the fan
and motor. Once completed, reassemble the side panel.
If maintenance must be carried out in a poorly lit area,
always employ an extra lamp to ensure that the work is
executed under safe conditions according to local law
requirements
The above picture is an extreme example
of a unit that was not maintained

Page - 16 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
BRUSH CHANGEOUT PROCEDURES :
Approximately once per year, the brushes should be replaced due to normal wear and tear. This is an
easy task to accomplish. Procedures follow.
The GP8 is equipped with 8 colour coded brushes – 3 red; 2 green and 3 yellow. The brushes are
comprised of a very durable, absorbent polystyrene. They were designed with two parts – the base
brush and then an interchangeable tip. This tip will essentially double the life of the brush.
Whether you are changing out an entire brush or replacing just a “tip” proceed as follows:
Ensure the unit has been turned off and is unplugged.
Remove the brush from the support by rotating the brush in a counter
clockwise direction while gently pulling it upwards.
Remove the brush completely by slipping it off its support.

Page - 17 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
REPLACE A FULL SET OF BRUSHES:
Ensure you have an 8 brush set – colour coded with 3 red; 2 green and 3 yellow
Place each brush on top of support (B) (matching the colours) and slide the brush down the support.
Ensure that slot (A) is connected by slightly rotating the brush in a clockwise direction. If the brush is
not properly fixed on the support, it will not rotate once the machine is switched on.
REPLACE THE GREEN BRUSH TIP:
Firmly grasp both ends of the
colour coded green brush
Twist until the brush separates into
two parts. Discard the worn brush
tip.
Fit the new tip into the brush and
twist until hand tight. The brush is
now ready to be put back onto its
support.
REPLACE THE RED OR YELLOW BRUSH TIP:
Using ‘needle-nose pliers’, grasp the lip of the brush tip and turn to the
left to loosen. This will require 2-3 turns using the pliers.
Continue turning the tip by hand
until the br ush is s eparated into
two parts. Discard the worn
brush tip.

Page - 18 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
Fit the new tip into the brush and turn until tight. DO NOT HOLD ONTO THE FRINGE WHILE
TURNING AS THIS MAY DAMAGE THE BRUSH. Use the pliers to tighten the tip until the last
thread is almost flush with the brush edge.
Replace the brushes on their color coded supports (red, green and yellow). Turn the brush in
a clockwise direction to lock in place. Be sure that the brushes are correctly inserted onto the
spindles

Page - 19 SALES + SERVICE
CPIGP8AOPINST [phone]
WWW.CPISHINE.COM
EXTRAORDINARY MAINTENANCE
This maintenance must be carried out only by a qualified technician.
Extraordinary maintenance is a rare occurrence and consists essentially of replacement.of one
of the following items:
 a damaged component
 a damaged electric cable (scratched, or compressed)

Update: 07/10/09 Page 20

Update: 07/10/09 Page 21