CPS DC-UPS SERIES User manual

ROUTER DC-UPS SERIES USER MANUAL
INTRODUCTION
Dimensions L x W x H (mm): 84 x 58 x 35
1. Input connector (5.5/2.1mm DC socket)
2. Backup mode shutdown button
3. Orange LED - Battery backup or adaptor power failure
4. Red LED - Flashing: Battery low; Still: Protection alarm
5. Blue LED - Protection mode ON
6. Green LED - Battery charging (off When Fully Charged)
7. Output cable
Below shows a typical Router application.
INSTALLATION & START UP
1. Firstly, unplug the adaptor from the power source. Disconnect the
adaptor from the equipment.
2. Connect the DC-UPS between AC/DC adaptor and the device (shown as
diagram on the left).
3. Switch on the adaptor power, check if the blue & green LED‟s are
illuminated.
4. Turn the adaptor power off, and check if UPS works in normal backup
mode.
5. Turn the Adaptor power on again, and check if UPS restores to Line
Mode (Blue LED light remain On, Yellow LED Off).
SHUT DOWN UPS
1. Switch off or unplug the adaptor power source.
2. Press and hold the shutdown button for 2 seconds and then release, the
status LED‟s will turn off.
IMPORTANT NOTES
1. Always turn the adaptor power on after the device/s are connected to
the UPS to prevent current over range protection mode shutdown.
2. If UPS shows protecting alarm (Red LED), turn off adaptor power first,
and turn the power back on after the UPS resets.
3. If the UPS repeats the protecting mode, recheck the starting sequence
and the equipment loading power rating. (Max 10 Watts)

ROUTER DC-UPS SERIES USER MANUAL
FEATURES
Simple “plug and play” installation Ultra slim compact design
Online style UPS design
Operating temperature range 0~50℃
Lithium Polymer battery technology
Microprocessor embedded control Advanced battery life management
system
Surge and lightning protection
Over voltage protection Overload/short circuit protection Auto start
and manual on/off switch
LED status indicators
Uses standard 5.5/2.1mm DC connectors
The CPS DC-UPS is a small, compact “online” 5~12V DC UPS system
that provide back-up power in the event of an input power failure.
Utilizing Lithium Polymer (Li-Po) battery technology, it can be used to
back-up 5~12V DC/AC devices up to 10W, such as routers, wireless
routers, modems, and access points.
MAINTENANCE
There is no regular maintenance required of this device. If the device
enters „Alarm‟ mode, the cause of the failure should be investigated
e.g. short circuit load or overload. The fault should be rectified before
restoring power to the device
SPECIFICATION
Input Spec
Voltage (operating)
Input current (max)
DC Input Connector
Output Spec
Voltage
Max Output Power
Max load current
DC Output Connector
Ripple
Overload protection
Transfer time
Battery
Type
Recharge time
Battery low/cut level
5~12V DC/AC auto recognition (+/- 5%)
2A max @ 5V
5.5x2.1; 5.5x2.5, 4.8x1.7mm DC socket
5/6/7.5/9/12V DC auto selection (+/- 5%)
10 Watt
2A/5V;1.6A/6V;1.3A/7.5V;1.1A/9V;0.8A/12V
5.5x2.1; 5.5x2.5, 4.8x1.7mm DC plug
1%
110%
0ms (zero)
Li-Polymer 3.7V
6hrs to 90% (1250mAh)
10hrs to 90% (2200mAh)
3.6V / 3.2V
Load Current
Estimated Backup Time (fully Charged)
Capacity
1250mAh
2200mAh
200mA
98 mins
178 mins
400mA
56 mins
98 mins
800mA
18 mins
38 mins