Craftsman 944.361064 User manual

Model No.
944.361064
CAUTION:
Read and follow all
Safety Rules and Instructions
before operating this equipment.
Owner’s Manual
WHEELED
WEEDTRIMMER
6.0 Horsepower
22 Inch Cut
Sears Canada, Inc., Toronto, Ontario M5B 2B8

2
Warranty ...................................................2
Safety Rules ..........................................3-4
Assembly / Pre-Operation ........................5
Operation...............................................6-8
Maintenance Schedule.............................9
Maintenance........................................9-11
Product Specifi cations ............................9
Service and Adjustments...................12-13
Storage ...................................................14
Troubleshooting ......................................15
Repair Parts.......................................16-25
Sears Service .......................... Back Cover
WARRANTY
TABLE OF CONTENTS
LIMITED TWO YEAR WARRANTY ON CRAFTSMAN WEEDTRIMMER
For two years from date of purchase, when this Craftsman Weedtrimmer is maintained,
lubricated, and tuned up according to the operating and maintenance instructions in the
owner’s manual, Sears Canada, Inc. will repair free of charge any defect in material or
workmanship.
If this Craftsman Weedtrimmer is used for commercial or rental purposes, this warranty
applies for only 90 days from the date of purchase.
This Warranty does not cover:
• Expendable items which become worn during normal use, such as rotating lines,
belts, air cleaners and spark plug.
• Repairs necessary because of operator abuse or negligence, including bent crank-
shafts and the failure to maintain the equipment according to the instructions con-
tained in the owner’s manual.
Warranty service is available by returning the Craftsman Weedtrimmer to the nearest
Sears Service Centre/Department in Canada. This warranty applies only while this prod-
uct is used in Canada.
This warranty is in addition to any statutory warranty and does not exclude or limit legal
rights you may have but shall run concurrently with applicable provincial legislation. Fur-
thermore, some provinces do NOT allow limitation on how long an implied warranty will
last so the above limitations may not apply to you.
Sears Canada, Inc., Toronto, Ontario M5B 2B8
WARNING: This trimmer is equipped with an internal combustion engine and should
not be used on or near any unimproved forest-covered, brush-covered or grass-covered
land unless the engine’s exhaust system is equipped with a spark arrester meeting ap-
plicable local or state laws (if any). If a spark arrester is used, it should be maintained in
effective working order by the operator.
In the state of California the above is required by law (Section 4442 of the California
Public Resources Code). Other states may have similar laws. Federal laws apply on
federal lands. A spark arrester for the muffler is available through your nearest Sears
Service Centre/Department in Canada (see the REPAIR PARTS section of this manual).

3
SAFETY RULES
Look for this symbol to point out im-
portant safety precautions. It means
CAUTION!!! BECOME ALERT!!!
YOUR SAFETY IS INVOLVED.
WARNING: In order to prevent ac-
cidental starting when setting up, trans-
porting, adjusting or making repairs,
always disconnect spark plug wire and
place wire where it cannot contact plug.
CAUTION: Muffler and other engine
parts become extremely hot during
operation and remain hot after engine has
stopped. To avoid severe burns on contact,
stay away from these areas.
trousers or slacks. Do not wear shorts.
• Do not wear loose clothing which could
get caught in this equipment.
• Do not operate the machine when bare-
foot or wearing open sandals. Always
wear work gloves and sturdy footwear.
Leather work shoes or short boots work
well for most people. These will protect
the operator’s ankles and shins from
small sticks, splinters, and other debris,
and improve traction.
• Do not pull machine backwards un-
less absolutely necessary. Always look
down and behind before and while mov-
ing backwards.
• Do not operate the machine without
proper guards, plates or other safety
protective devices in place.
• See manufacturer’s instructions for
proper operation and installation of
accessories. Only use accessories ap-
proved by the manufacturer.
• Never use blades, wire, or flailing devices.
This unit is designed for line trimmer use
only. Use of other accessories or attach-
ments will increase the risk of injury.
• Stop the rotating trimmer head when
crossing gravel drives, walks, or roads.
Wait for the cutting lines to stop rotating.
• Stop the engine (motor) whenever you
leave the equipment and allow it to cool,
before cleaning, repairing or inspecting
the unit. Be sure the trimmer head and
all moving parts have stopped.
• Operate only in daylight or good artificial
light.
• Do not operate the machine while under
the influence of alcohol or drugs.
• Never operate machine in wet grass. Al-
ways be sure of your footing: keep a firm
hold on the handle and walk; never run.
• If the equipment should start to vibrate
abnormally, stop the engine (motor) and
check immediately for the cause. Vibra-
tion is generally a warning of trouble.
• Always wear safety goggles or safety
glasses with side shields when oper-
ating machine.
The operation of any trimmer can result in foreign objects thrown into
the eyes, which can result in severe eye damage. Always wear safety
glasses or eye shields while operating your trimmer or performing any
adjustments or repairs. We recommend standard safety glasses or a
wide vision safety mask worn over spectacles.
I. GENERAL OPERATION
• Read, understand, and follow all instruc-
tions on the machine and in the manual
before starting. Be thoroughly familiar
with the controls and the proper use of
the machine before starting.
• Do not put hands or feet near or under
rotating parts.
• Keep all parts of your body away from
muffler and spinning line. A hot muffler
can cause serious burns.
• Only allow responsible individuals, who
are familiar with the instructions, to
operate the machine.
• Stay away from breakable objects, such
as house windows, auto glass, green-
houses, etc.
• Cleartheareaofobjectssuchasrocks,toys,
wire, bones, sticks, etc., which could be
picked up and thrown by the spinning lines.
• Be sure the area is clear of other people
before trimming, particularly small chil-
dren and pets. Stop machine if anyone
enters the area.
• Wear appropriate clothing such as a long-
sleeved shirt or jacket. Also wear long

4
II. SLOPE OPERATION
Slopes are a major factor related to slip
and fall accidents which can result in
severe injury. All slopes require extra cau-
tion. If you feel uneasy on a slope, do not
trim it.
DO:
• Trim across the face of slopes: never up
and down. Exercise extreme caution
when changing direction on slopes.
• Remove obstacles such as rocks, tree
limbs, etc.
• Watch for holes, ruts, or bumps. Tall
grass can hide obstacles.
DO NOT:
• Do not trim near drop-offs, ditches or
embankments. The operator could lose
footing or balance.
• Do not trim excessively steep slopes.
• Do not trim on wet grass. Reduced foot-
ing could cause slipping.
III. CHILDREN
Tragic accidents can occur if the operator
is not alert to the presence of children.
Children are often attracted to the machine
and the trimming activity. Never assume
that children will remain where you last
saw them.
• Keep children out of the trimming area
and under the watchful care of another
responsible adult.
• Be alert and turn machine off if children
enter the area.
• Before and while moving backwards,
look behind and down for small children.
• Never allow children to operate the
machine.
• Use extra care when approaching blind
corners, shrubs, trees, or other objects
that may obscure vision.
IV. SERVICE
• Use extra care in handling gasoline and
other fuels. They are flammable and
vapors are explosive.
- Use only an approved container.
- Never remove gas cap or add fuel
with the engine running. Allow
engine to cool before refueling.
Do not smoke.
- Never refuel the machine indoors.
- Never store the machine or fuel
container inside where there is an
open flame, such as a water heater.
- Move away from fueling site before
starting engine.
• Never run a machine inside a closed
area.
• Never make adjustments or repairs with
the engine (motor) running. Disconnect
the spark plug wire, and keep the wire
away from the plug to prevent accidental
starting.
• Keep nuts and bolts, especially trimmer
head and engine bolts, tight and keep
equipment in good condition.
• Never tamper with safety devices.
Check their proper operation regularly.
• Keep machine free of grass, leaves, or
other debris buildup. Clean oil or fuel
spillage. Allow machine to cool before
cleaning or storing.
• Stop and inspect the equipment if you
strike an object. Repair, if necessary,
before restarting.
• Do not change the engine governor set-
ting or overspeed the engine.
• Clean and replace safety and instruction
decals as necessary.

5
ASSEMBLY / PRE-OPERATION
Read these instructions and this manual in
its entirety before you attempt to assemble
or operate your new trimmer.
IMPORTANT: This trimmer is shipped
WITHOUT OIL OR GASOLINE in the
engine.
Your new trimmer has been assembled
at the factory with the exception of those
parts left unassembled for shipping
purposes. All parts such as nuts, wash-
ers, bolts, etc., necessary to complete the
assembly have been placed in the parts
bag. To ensure safe and proper operation
of your trimmer, all parts and hardware
you assemble must be tightened securely.
Use the correct tools as necessary to
ensure proper tightness.
When right hand (RH) or left hand (LH) is
mentioned in this manual, it means when
you are in the operating position (standing
behind the handle).
TO REMOVE TRIMMER FROM
CARTON
1. Remove loose parts included with trim-
mer.
2. Cut down two end corners of carton
and lay end panel down flat.
3. Remove all packing materials.
4. Roll trimmer out of carton and check
carton thoroughly for additional loose
parts.
HOW TO SET UP YOUR TRIMMER
TO UNFOLD HANDLE
IMPORTANT: Unfold handle carefully so
as not to pinch or damage control cables.
1. Loosen handle knob enough to allow
upper handle to be unfolded from the
shipping position.
2. Raise upper handle section into place
on lower handle and tighten handle
knob.
3. Remove handle padding holding trim-
mer head control bar to upper handle.
Your trimmer handle can be adjusted for
your trimming comfort. Refer to “ADJUST
HANDLE” in the Service and Adjustments
section of this manual.
Loose Parts Packed Separately
Bottle of oil
Trimmer Lines
(2) Sets
(0.155 diameter
x 18.75 inches long)
LIFT UP
Lower
handle
Upper handle
Handle
knob

6
ATTENTION OU
AVERTISSEMENT
RAPIDE LENT COUPER
LE MOTEUR
HUILE
ESSENCE
OPERATION
KNOW YOUR TRIMMER
READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING
YOUR TRIMMER. Compare the illustrations with your trimmer to familiarize yourself with
the location of various controls and adjustments. Save this manual for future reference.
Starter handle
Gasoline cap
Air filter
Trimmer head
Handle knob
Trimmer line
Engine oil cap w/dipstick
Chassis cover
Trimmer head control bar
Throttle control
Throttle control – used for starting and
stopping the engine and allows you to
select either fast or slow engine speed.
Starter handle – used for starting the
engine.
Trimmer head control bar – must be
held down to the handle to engage trimmer
head. Release to stop the trimmer head.
Primer – pumps additional fuel from the
carburetor to the cylinder for use when
starting a cold engine.
These symbols may appear on your trimmer or in literature supplied with the product. Learn and
understand their meaning.
IMPORTANT: This trimmer is shipped
WITHOUT OIL OR GASOLINE in the engine.
Primer
Muffler

7
HOW TO USE YOUR TRIMMER
ENGINE SPEED
The engine speed is controlled by a throt-
tle located on the side of the upper handle.
FAST position is for starting and normal
trimming. SLOW is for light trimming and
fuel economy. STOP is for stopping the
engine.
The operation of any trimmer can result in
foreign objects being thrown into the eyes,
which can result in severe eye damage.
Always wear safety glasses or eye shields
while operating your trimmer or performing
any adjustments or repairs. We recom-
mend standard safety glasses or a wide
vision safety mask worn over spectacles.
TO ADJUST TRIMMING HEIGHT
CAUTION: Stop the engine and wait for
all moving parts to stop. Disconnect spark
plug wire from spark plug and place wire
where it cannot come in contact with plug.
The height of cut can be set to six (6) dif-
ferent positions ranging from 1-1/2 inches
to 3 inches. Recommended cutting height
for the average yard is 2 inches.
1. To adjust trimming height, push in the
locking plate tab and move trimmer
head up or down to desired position.
2. Release tab and be sure head is
locked into one of the six (6) height
positions.
TRIMMER HEAD DRIVE CONTROL
Your trimmer is equipped with a trimmer
head drive control bar which will require
the operator to be positioned behind the
trimmer handle to operate the trimmer.
• Trimmer head rotation is controlled by
holding the trimmer head control bar
down to the handle.
• Trimmer head rotation will stop when
the control bar is released.
STOP
BEFORE STARTING ENGINE
ADD OIL
Your trimmer is shipped without oil in the
engine. For type and grade of oil to use,
see “ENGINE” in the Maintenance section
of this manual.
CAUTION: DO NOT overfill engine with
oil, or it will smoke on startup.
1. Be sure trimmer is level and area
around oil fill is clean.
2. Remove oil dipstick from oil fill spout.
Make sure that rim of spout is clean.
3. You receive a container of oil with the
unit. Slowly pour the entire container
down the oil fill spout into the engine.
NOTE: Initial oil fill requires only 18 oz.
due to residual oil in engine from the
manufacturers 100% quality testing. When
changing oil you may need 20 oz.
4. Insert and tighten dipstick.
Locking
Plate Tab
Adjustable
Trimmer
Head

8
TRIMMING TIPS
• Set the throttle control in the FAST posi-
tion. If the weeds or grass are tall and
thick, operate the trimmer at a slower
walking speed.
• Frequently clean the underside of the
trimmer to remove any grass build up.
Keep top of engine around starter clear
and clean of grass clippings and chaff.
This will help engine air flow and extend
engine life.
• For best results and longer lasting
line, use the ends of the line to do the
cutting. This is easily done by moving
slowly through very thick and heavy
weeds.
• Use the left side of trimmer when trim-
ming along fences, walls, flowerbeds
and other such objects.
• If trimmer lines become too short, it will
take longer to complete the job. If trim-
mer lines are worn to less than half their
original length, they should be replaced.
See “TO REPLACE TRIMMER LINE” in
the Maintenance section of this manual.
• Trimmer head contact with concrete, as-
phalt or other hard surfaces may cause
premature wear of the ball on bottom of
trimmer head.
IMPORTANT:
• Check oil level before each use. Add oil
if needed. Fill to full line on dipstick.
• Change the oil after every 25 hours of
operation or each season. You may
need to change the oil more often under
dusty, dirty conditions.
ADD GASOLINE
• Fill fuel tank to bottom of tank filler neck.
Do not overfill. Use fresh, clean, regular
unleaded gasoline with a minimum of 87
octane. Do not mix oil with gasoline. Pur-
chase fuel in quantities that can be used
within 30 days to assure fuel freshness.
CAUTION: Alcohol blended fuels
(called gasohol or using ethanol or
methanol) can attract moisture which
leads to separation and formation of acids
during storage. Acidic gas can damage
the fuel system of an engine while in
storage. To avoid engine problems, the
fuel system should be emptied before
storage of 30 days or longer. Drain
the gas tank, start the engine and let it
run until the fuel lines and carburetor
are empty. Use fresh fuel next season.
See Storage Instructions for additional
information. Never use engine or
carburetor cleaner products in the fuel
tank or permanent damage may occur.
CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
Starter handle
Throttle control
Gasoline
filler cap
Engine
oil cap
Primer
2. Move throttle control lever to FAST
position.
3. Hold upper handle firmly and pull
starter handle quickly. Do not allow
starter rope to snap back.
NOTE: In cooler weather it may be
necessary to repeat priming steps. In
warmer weather overpriming may cause
flooding and engine will not start. If you
do flood engine, wait a few minutes before
attempting to start and DO NOT repeat
priming steps.
TO STOP ENGINE
• To stop engine, move throttle control
lever to STOP position.
TO START ENGINE
1. To start a cold engine, push primer three
(3) times before trying to start. Use a
firm push. This step is not usually neces-
sary when starting an engine which has
already run for a few minutes.

9
MAINTENANCE
GENERAL RECOMMENDATIONS
The warranty on this trimmer does not cover
items that have been subjected to operator
abuse or negligence. To receive full value
from the warranty, operator must maintain
trimmer as instructed in this manual.
Some adjustments will need to be made
periodically to properly maintain your unit.
At least once a season, check to see if
you should make any of the adjustments
described in the Service and Adjustments
section of this manual.
• At least once a year, replace the spark
plug and replace air filter element. A
new spark plug and clean/new air filter
element assure proper air-fuel mixture
and help your engine run better and last
longer.
• Follow the maintenance schedule in
this manual.
BEFORE EACH USE
1. Check engine oil level.
2. Check for loose fasteners.
3. Clean under engine cover.
LUBRICATION
To prolong the useful life of your trimmer,
change engine oil as recommended in this
section of this Owner’s Manual.
IMPORTANT: Do not oil or grease plastic
wheel bearings. Viscous lubricants will
attract dust and dirt that will shorten the
life of the self- lubricating bearings. If you
feel they must be lubricated, use only a dry,
powdered graphite type lubricant sparingly.
PRODUCT SPECIFICATIONS
Serial No. __________________________
Date of Purchase: ____________________
Gasoline Type: Unleaded Regular
Gasoline Capacity: 1,5 Liters
Oil Type: SAE 30 (Above 32º F)
(API-SF-SJ) SAE 5W-30 (Below 32º F)
Oil Capacity: 0,58 Liters
Spark Plug: Champion RJ19LM
(Gap: 0,76 mm)
Trimmer Line Diameter: 0,155 inch
Trimmer Line Length: 18,75 inches
The model and serial numbers will be found
on a decal attached to the rear of the trim-
mer. Record both serial number and date of
purchase in the space provided above.

10
ENGINE
LUBRICATION
Use only high quality detergent oil rated
with API service classification SF-SJ.
Select the oil's SAE viscosity grade according
to your expected operating temperature.
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
SAE VISCOSITY GRADES
-20 0 30 40 80 100
-30 -20 0 20 30 40
F
C
32
-10 10
60
5W-30
SAE 30
TRIMMER
Always observe safety rules when per-
forming any maintenance.
TIRES
• Keep tires free of gasoline, oil, or insect
control chemicals which can harm rub-
ber.
• Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
TRIMMER LINE
For best results, replace trimmer lines
when they have worn to half their original
length. Use .155 inch diameter trimmer
line. Cut new trimmer line length to 18-3/4
inches. After new line is installed on
trimmer head, check all lines so they do
not vary more then one (1) inch in length.
This is important to make sure the trim-
mer head is balanced and will not vibrate
abnormally.
WARNING:Use only the specified trimmer
line.Do not use other materials such as wire,
string, rope, etc. Wire can break off during
trimming and become a dangerous missile
that can cause serious injury.
TO CUT LINE TO PROPER LENGTH
NOTE: Trimmer line pre-cut to proper
length is available for this unit; see the
Repair Parts section of this manual.
If trimmer line is purchased in bulk, it must
be cut to 18-3/4 inches before using. Use
the built-in length guage as follows:
1. From front of trimmer, place the end of
spooled trimmer line at the mark on the
side of the debris shield as shown.
2. Wrap trimmer line around front of chas-
sis cover to other side and cut at the
“22” mark (your unit’s width of cut).
TO REPLACE TRIMMER LINE
1. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with plug.
2. Remove worn trimmer line from line
carrier plate.
3. Fold new, cut to length, trimmer line in half
and insert folded end through carrier plate
opening to back side of retainer clip.
4. With folded end of line at back side of
retainer clip, pull line outward until line
is fully seated under the retainer clip.
5. Repeat on other side of carrier plate.
6. Check all lines to be sure they are the
same length.
7. Reconnect spark plug wire to plug.
Retainer clip
Carrier plate
opening
Trimmer
line
New
trimmer
line
Chassis cover
WRAP
LINE
AROUND
End of
spooled line
Debris
shield
mark

11
Container
3. Clean by gently tapping on a flat sur-
face. If very dirty, replace cartridge.
CAUTION: Petroleum solvents, such as
kerosene, are not to be used to clean car-
tridge. They ma y cause deterioration of the
cartridge. Do not oil cartridge. Do not use
pressurized air to clean or dry cartridge.
4. Install cartridge, then replace cover mak-
ing sure the tabs are aligned with the slots
in the back plate. Fasten screw securely.
NOTE: Although multi-viscosity oils (5W30,
10W30 etc.) improve starting in cold weather,
these multi-viscosity oils will result in in-
creased oil consumption when used above
32°F. Check your engine oil level more fre-
quently to avoid possible engine damage
from running low on oil.
Change the oil after every 25 hours of
operation or at least once a year if the unit
is not used for 25 hours in one year.
Check the crankcase oil level before
starting the engine and after each five (5)
hours of continuous use. Tighten oil plug
securely each time you check the oil level.
TO CHANGE ENGINE OIL
NOTE: Before tipping trimmer to drain oil,
empty fuel tank by running engine until
fuel tank is empty.
1. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with plug.
2. Remove engine oil cap; lay aside on a
clean surface.
3. Tip trimmer on its side as shown and
drain oil into a suitable container. Rock
trimmer back and forth to remove any
oil trapped inside of engine.
Slots
Lip
Cover
tabs
Back plate
Cartridge Cover
4. Wipe off any spilled oil from trimmer or
side of engine.
5. Fill engine with oil (See “ADD OIL” in
the Operation section of this manual).
6. Replace engine oil cap.
7. Reconnect spark plug wire to plug.
AIR FILTER
Your engine will not run properly and may
be damaged by using a dirty air filter.
Replace the air filter cartridge every 100
hours of operation or every season, which-
ever occurs first. Service air cleaner more
often under dusty conditions.
TO CLEAN AIR FILTER
1. Loosen screw and tilt cover to remove.
2. Carefully remove cartridge.
MUFFLER
Inspect and replace corroded muffler as it
could create a fire hazard and/or damage.
SPARK PLUG
Replace spark plug at the beginning of
each mowing season or after every 100
hours of operation, whichever occurs
first. Spark plug type and gap setting
are shown in the “PRODUCT SPECIFIC-
ATIONS” section of this manual.
CLEANING
IMPORTANT: For best performance, keep
trimmer free of built-up grass and trash.Clean
the underside of your trimmer after each use.
CAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with plug.
• Turn trimmer on its side. Make sure air
filter and carburetor are up. Clean the
underside of your trimmer by scraping to
remove build-up of grass and trash.
• Clean engine often to keep trash from
accumulating. A clogged engine runs
hotter and shortens engine life.
• Keep finished surfaces and wheels free
of all gasoline, oil, etc.
• We do not recommend using a garden
hose to clean trimmer unless the elec-
trical system, muffler, air filter and car-
buretor are covered to keep water out.
Water in engine can result in shortened
engine life.

12
Chassis
cover
Screw
TO REMOVE/REPLACE TRIMMER HEAD
DRIVE BELT
1. Remove screw at front of chassis cover.
2. Lift cover up and away from trimmer.
SERVICE AND ADJUSTMENTS
WARNING: To avoid serious injury,
before performing any service and
adjustments:
1. Stop engine.
2. Make sure the rotating lines and all
moving parts have completely stopped.
3. Disconnect spark plug wire from spark
plug and place wire where it cannot
come into contact with plug.
TRIMMER
TO ADJUST TRIMMING HEIGHT
See “TO ADJUST TRIMMING HEIGHT” in
the Operation section of this manual.
TO ADJUST HANDLE
The upper handle may be adjusted to dif-
ferent height positions.
1. Loosen handle knob only enough to
allow the upper handle to pivot to the
desired position.
2. Tighten handle knob securely.
NOTE: The handle knob and bolt may be
reversed for left handed operation.
Debris shield screws
Engine
pulley
3. Remove the two (2) screws on sides of
trimmer securing the debris shield.
4. Turn trimmer on its side with carburetor
and fuel cap up.
5. Remove the two (2) screws on under-
side of trimmer securing the debris
shield.
6. Slide the debris shield rearward and
remove.
7. Remove belt from engine pulley on
crankshaft.
Handle knob
Upper
handle

13
Belt
Idler bracket
Engine pulley
Trimmer head pulley
Top belt keeper
Chassis
Flat idler
Nut Spacer
Bottom
belt
keeper
Idler assembly
Spacer
Bolt
V-idler
Flat idler
Control cable
Idler
spring
12.Position belt and idler assembly in
trimmer, reconnect idler spring and as-
semble idler to chassis.
13.Install belt around trimmer head pulley
and engine pulley.
14.Replace debris shield and tighten the
four (4) screws securely.
15.Replace chassis cover and tighten
screw securely.
Always use Craftsman replacement parts
to assure proper fit and long life.
8. Remove belt from trimmer head pulley.
9. Note the position of the control cable
and idler return spring, then remove
idler assembly from chassis and re-
move belt and idler from trimmer.
10.Remove belt from idler assembly by
removing bottom belt keeper and idler
pulleys.
11.Assemble new belt, idler pulleys and
bottom belt keeper to idler bracket.
Tighten pulley bolts securely.
NOTE: Be sure belt is inside top belt
keeper on idler assembly.
ENGINE
ENGINE SPEED
Your engine speed has been factory set.
Do not attempt to increase engine speed
or it may result in personal injury. If you
believe that the engine is running too fast
or too slow, take your unit to a Sears or
other qualified service center for repair
and/or adjustment.
CARBURETOR
Your carburetor has a nonadjustable fixed
main jet for mixture control. If your engine
does not operate properly due to sus-
pected carburetor problems, take your unit
to a Sears or other qualified service center
for repair and/or adjustment.
IMPORTANT: Never tamper with the
engine governor, which is factory set
for proper engine speed. Overspeeding
the engine above the factory high speed
setting can be dangerous. If you think
the engine-governed high speed needs
adjusting, take your unit to a Sears or
other qualified service center, which has
proper equipment and experience to make
any necessary adjustments.

14
STORAGE
Immediately prepare your trimmer for stor-
age at the end of the season or if the unit
will not be used for 30 days or more.
TRIMMER
When trimmer is to be stored for a period
of time, clean it thoroughly, remove all dirt,
grease, leaves, etc. Store in a clean, dry area.
1. Clean entire trimmer (See “CLEANING”in
the Maintenance section of this manual).
2. Lubricate as shown in the Maintenance
section of this manual.
3. Be sure that all nuts, bolts, screws, and
pins are securely fastened. Inspect
moving parts for damage, breakage
and wear. Replace if necessary.
4. Touch up all rusted or chipped paint
surfaces; sand lightly before painting.
HANDLE
You can fold your trimmer handle for storage.
• Loosen handle knob enough to allow
upper handle to be folded forward.
IMPORTANT: When folding the handle for
storage or transportation, be sure to fold
the handle as shown or you may damage
the control cables.
ENGINE
FUEL SYSTEM
IMPORTANT: It is important to prevent
gum deposits from forming in essential
fuel system parts such as carburetor, fuel
filter, fuel hose or tank during storage.
Also, alcohol blended fuels (called gasohol
or using ethanol or methanol) can attract
moisture which leads to separation and
formation of acids during storage. Acidic
gas can damage the fuel system of an
engine while in storage.
• Empty the fuel tank by starting the en-
gine and letting it run until the fuel lines
and carburetor are empty.
• Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable
alternative in minimizing the formation
of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or
storage container. Always follow the mix
ratio found on stabilizer container. Run
engine at least 10 minutes after adding
stabilizer to allow the stabilizer to reach
the carburetor. Do not drain the gas tank
and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace
with clean engine oil. (See “ENGINE” in
the Maintenance section of this manual).
CYLINDER
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through
spark plug hole into cylinder.
3. Pull starter handle slowly a few times
to distribute oil.
4. Replace with new spark plug.
OTHER
• Do not store gasoline from one season
to another.
• Replace your gasoline can if your can
starts to rust. Rust and/or dirt in your
gasoline will cause problems.
• If possible, store your unit indoors and
cover it to protect it from dust and dirt.
• Cover your unit with a suitable protective
cover that does not retain moisture. Do
not use plastic. Plastic cannot breathe,
which allows condensation to form and
will cause your unit to rust.
IMPORTANT: Never cover trimmer while
engine and exhaust areas are still warm.
CAUTION: Never store the trimmer
with gasoline in the tank inside a building
where fumes may reach an open flame
or spark. Allow the engine to cool before
storing in any enclosure.
Upper
handle
Handle
knob

15
Does not start 1. Dirty air filter. 1. Clean/replace air filter.
2. Out of fuel. 2. Fill fuel tank.
3. Stale fuel. 3. Empty fuel tank and refill
with fresh, clean gasoline.
4. Water in fuel. 4. Empty fuel tank and refill
with fresh, clean gasoline.
5. Spark plug wire is 5. Connect wire to plug.
disconnected.
6. Bad spark plug. 6. Replace spark plug.
7. Throttle control lever not 7. Move throttle lever to FAST
in correct position position.
(if equipped).
Loss of power 1. Dirty air filter. 1. Clean/replace air filter.
2. Buildup of grass, leaves, 2. Clean underside of trimmer
and trash under trimmer. and trimmer head.
3. Too much oil in engine. 3. Check oil level.
4. Walking speed too fast. 4. Trim at slower walking
speed.
Excessive 1. Lines uneven or broken. 1. Check trimmer lines.
Vibration 2. Loose nuts or bolts. 2. Check all hardware,
including engine bolts.
3. Damaged trimmer head. 3. Check/repair trimmer head.
Starter rope 1. Bent engine crankshaft. 1. Contact a Sears or other
hard to pull qualified service center.
Loss of head 1. Belt not driving. 1. Put belt on pulleys or
drive replace belt if broken.
Hard to push 1. Handle height position not 1. Adjust handle height
right for you. to suit.
Poor trimming 1. Trimmer line length is 1. If line is worn or broken to
performance too short. half original length,
replace line.
2. Throttle control lever not 2. Move throttle lever to FAST
in correct position position.
(if equipped).
Trimmer head 1. Trimmer line not 1. Follow instructions in the
does not properly installed. Maintenance section.
retain line 2. Broken line retainer clip. 2. Replace string carrier plate
assembly.
3. Incorrect size of 3. Use .155 inch diameter
trimmer line. trimmer line.
PROBLEM CAUSE CORRECTION
TROUBLESHOOTING - See appropriate section in manual unless directed
to a Sears Service Centre / Department.

16
CRAFTSMAN WEED TRIMMER - - MODEL NUMBER 944.361064
REPAIR PARTS
32
11
18
20
33
12
15
15
9
8
9
26
27
23
24 22
2
3
40
38 39
23
24
10
16
21 26
27
19
28
35
34
3736 1
29
30

17
KEY PART
NO. NO. DESCRIPTION
1 - - - Engine, Briggs & Stratton,
Model Number 122H02-0220-B1
(See Breakdown)
2 150406 Bolt, Engine Mounting 3/8-16
3 179466 Pulley, Engine
8 169821X479 Handle, Lower
9 150078 Screw, Hex Washer Head 5/16-18 x .75
10 177815 Handle, Upper
11 170980 Bolt, Handle
12 189713X428 Knob, Handle
15 179751 Handle Adjuster Assembly
16 179585 Guide, Rope
18 66426 Wire Tire
19 176983 Control Bar
20 177814 Throttle Control
21 158755 Screw, Hex Washer Head
22 178702X004 Axle Shaft Assembly
23 150078 Screw, Hex Washer Head 5/16-18 x .75
24 52160 Washer, Axle
26 177637 Wheel, 16 x 2
27 83923 Hex Flange Locknut 3/8-16
28 181699 Drive Control Cable
29 178844 Decal, Warning
30 178365 Decal, Warning
32 164265 Grip, Handle
33 132004 Nut, Hex
34 86899X004 Bracket, Upstop
35 750634 Screw, Thd. Roll. #10-24 x 5/8
36 111190X Clamp, Cable
37 83816 Screw
38 851084 Bolt, Hex Head
39 850263 Washer, Lock
40 851074 Washer, Flat, Hardened
- - 190976 Owner's Manual, English
- - 190979 Owner's Manual, French
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
CRAFTSMAN WEED TRIMMER - - MODEL NUMBER 944.361064

18
CRAFTSMAN WEED TRIMMER - - MODEL NUMBER 944.361064
12
43
14
1
52 51
17
4
13
53
16
18
34
33
39
38
27
37
27
30*
36
31
35
32
3
3
22
23
24
25
26
27*
28
9
10
7
6
41
5
8
11
15
29
40 45
21 47
46
20 44
2

19
CRAFTSMAN WEED TRIMMER - - MODEL NUMBER 944.361064
KEY PART
NO. NO. DESCRIPTION
1 174031X558 Chassis Assembly
2 182133 Line, Trimmer .155 diameter x 18.75 long
3 173715 Screw, Self-Tapping 5/16-18 x 1
4 185476 V-Belt
5 172145X004 Bracket, Idler
6 166042 Pulley, Idler, V-Groove
7 173716 Bolt, Hex Head 3/8-16 x 1.25
8 751592 Locknut, Hex 3/8-16
9 166043 Pulley, Idler, Flat
10 160829 Bolt, Shoulder
11 155552 Locknut 5/16-18
12 173717 Spacer
13 174719 Bolt, Shoulder
14 145212 Locknut, Flange
15 173811 Spring, Return
16 180268 Deflector, Bottom
17 57808 Screw 1/4-20 x 1/2
18 178848 Screw #10-24 x 3/4
20 170553 Cover, Chassis, Top
21 149746 Screw #10-24 x 1-3/4
22 STD541137 Nut, Hex 3/8-24 UNF
23 STD551137 Washer, Lock 3/8
24 STD551037 Washer, Flat 3/8
25 180340 Pulley, Driven
26 172551 Spacer, Pulley
27 174549 Bearing
28 172520 Jackshaft
29 169766X479 Cover, Chassis, Bottom
30 174543 Spindle Housing Assembly
(* Includes Upper Bearing, Key Number 27)
31 174581 Ring, Retaining, External, 17mm
32 176973 Spring, Locking Plate
33 172519 Locking Plate
34 180338 Carrier Plate Assembly
35 182217 Mow Ball Assembly
(Includes Key Numbers 27, 37 and 38)
36 172516 Cover, Bearing
37 174580 Ring, Retaining, Internal, 40mm
38 172523 Mow Ball
39 180334 Bolt, Mow Ball
40 180333 Spindle Assembly, Complete
(Includes Key Numbers 22-28 and 30-39)
41 174029 Spacer
43 174042 Decal, Instruction
44 174035 Decal, Chassis Cover
45 174596X479 Belt Keeper, Bottom
46 17060408 Screw, Self-Tapping
47 174510 Decal, Instruction
51 179875 Deflector, Rear
52 178848 Screw
53 187336 Belt Keeper
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

20
MODEL NUMBER 122H02-0220-B1
BRIGGS & STRATTON 4-CYCLE ENGINE
122H02-0220-B1
50
51
54
584
684
585
383
337
635
5
7
306
307
13
34
33
35
36
40
40
45
45
24
523
847
842
871
870
869
12
3
287
525
524
11
8
9
10
16
146
741
32
32A
29
28
27
27
26
25
12
15
20
4
1058 OWNER'S MANUAL
46
43
22
1019 LABEL KIT
718