Craftsman WEEDWACKER 358.795540 User manual

Instruction Manual
25cc/1.5 cu.in. 2-Cycle
17 Inch Cutting Path /0.080 In. Line
GASOLINE WEEDWAOKER ®
Model No.
358.795540
• Safety
•Assembly
• Operation
•Maintenance
•Parts List
•Espar_ol
For Occasional Use Only ®
WARNING:
Read and follow all Safety Rules and Operating
Instructions before first use of this product.
For answers to your questions about this product:
Call 7 am-7 pm, Mon.-Sat., or 10 am-7 pm, Sun.
1-800-235-5878 (Hours listed are Central Time)
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
530088291 4/19/02

Warranty Statement 2 Storage 11
Safety Rules 2 Troubleshooting Chart 12
Assembly 4 Emissions Statement 13
Operation 5 Parts List 15
Maintenance 9 Spanish 18
Service & Adjustments 10 Parts and Ordering Back Cover
FULL ONE YEAR WARRANTY ON CRAFTSMAN ® GAS POWERED
WEEDWACKER ®LINE TRIMMER
For one year from the date of purchase, when this Craftsman Gas Powered
Weedwacker Line Trimmer is maintained, lubricated, and tuned up according to
the operating and maintenance instructions in this manual, Sears will repair, free
of charge, any defect in materials or workmanship.
This warranty excludes nylon line, spark plug, and air filter, which are expendable
parts and become worn during normal use.
If this Weedwacker line trimmer is used for commercial purposes, this warranty ap-
plies for only 90 days from the date of purchase. If this Weedwacker line trimmer is
used for rental purposes, this warranty applies for only 30 days from the date of pur-
chase. This warranty applies only while this product is in use in the United States.
WARRANTY SERVICE ISAVAILABLEBY RETURNING THE WEEDWACKER LINE TRIMMER
TO THE NEAREST SEARS STORE OR SERVICE CENTER INTHE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Sears, Roebuck and Co., D/817 WA, Hoffman Estates, IL 60179
z_
4t_WARNING: When using gar-
dening appliances, basic safety pre-
cautions must always be followed to
reduce the risk of fire and serious
injury. Read and follow all instructions.
Thb power unit can be dangerous! Op-
erator is responsible for following
instructions and warnings on unit and in
manual. Read entire instruction manual
before using unit! Be thoroughly familiar
with the controls and the proper use of
the unit. Restrict the use of this unit to
persons who have read, understand,
and will follow the instructions and
warnings on the unit and in the manual.
Never allow children to operate this unit.
INSTRUCTION SAFETY INFORMATION
MANUAL ON THE UNIT
_i DANGER: Never use blades or
flailing devices. This unit is designed
for line trimmer use only. Use of any
other accessories or attachments will
increase the risk of injury.
©
• IWARNING: Trimmer line throws
objects violently. You and others can be
blinded/injured. Wear eye and leg
protection. Keep body parts clear of ro-
tating line.
_otection
Keep children, bystanders, and animals
50 feet (15 meters) away. Stop unit im-
mediately if approached.
2

Ifsituationsoccurwhicharenotcov-
eredinthismanual,usecareand
goodjudgment.Ifyouneedassis-
tance,contactyourSearsService
Centerorcall1-800-235-5878.
OPERATORSAFETY
• Dress properly. Always wear safety
glasses or similar eye protection
when operating, or performing main-
tenance, on your unit (safety
glasses are available). Eye protec-
tion should be marked Z87.
• Always wear face or dust mask ifop-
eration is dusty.
• Always wear heavy, long pants, long
sleeves, boots, and gloves. Wear-
ing safety leg guards is recom-
mended.
• Always wear foot protection. Do not
go barefoot or wear sandals. Stay
clear of spinning line.
• Secure hair above shoulder length.
Secure or remove loose clothing or
clothing with loosely hanging ties,
straps, tassels, etc. They can be
caught in moving parts.
• Being fully covered also helps pro-
tect you from debris and pieces of
toxic plants thrown by spinning line.
• Stay Alert. Do not operate this unit
when you are tired, ill, upset or un-
der the influence of alcohol, drugs,
or medication. Watch what you are
doing; use common sense.
• Wear hearing protection.
• Never start or run inside a closed
room or building. Breathing exhaust
fumes can kill.
• Keep handles free of oil and fuel.
UNIT /MAINTENANCE SAFETY
• Disconnect the spark plug before
performing maintenance except car-
buretor adjustments.
• Look for and replace damaged or
loose parts before each use. Look
for and repair fuel leaks before use.
Keep in good working condition.
• Replace trimmer head parts that are
chipped, cracked, broken, or dam-
aged in any other way before using
the unit.
• Maintain unit according to recom-
mended procedures. Keep cutting
line at proper length.
• Use only 0.080 inch (2 ram) diame-
ter CraftsmanC_ brand line. Never
use wire, rope, string, etc.
• Install required shield properly be-
fore using the unit. Use only speci-
fied trimmer head; make sure it is
properly installed and securely fas-
tened.
• Make sure unit is assembled cor-
rectly as shown in this manual.
• Make carburetor adjustments with
lower end supported to prevent line
from contacting any object.
• Keep others away when making car-
buretor adjustments.
• Use only recommended Craftsman(R_
accessories and replacement parts.
• Have all maintenance and service
not explained in this manual per-
formed by a Sears Service Center.
FUEL SAFETY
• Mix and pour fuel outdoors.
• Keep away from sparks or flames.
• Use a container approved for fuel.
• Do not smoke or allow smoking near
fuel or the unit.
• Avoid spilling fuel or oil. Wipe up all
fuel spills.
• Move at least 10 feet (3 meters)
away from fueling site before start-
ing engine.
• Stop engine and allow to cool before
removing fuel cap.
• Always store gasoline in a container
approved for flammable liquids.
CUTTING SAFETY
A0_'WARNING: Inspect the area be-
fore each use. Remove objects
(rocks, broken glass, nails, wire, etc.)
which can be thrown by or become
entangled in line. Hard objects can
damage the trimmer head and be
thrown causing serious injury.
• Use only for trimming, edging, scalp-
ing, mowing and sweeping. Do not
use for pruning or hedge trimming.
• Keep firm footing and balance. Do
not overreach.
• Keep all parts of your body away
from muffler and spinning line. Keep
engine below waist level. A hot muf-
fler can cause serious burns.
• Cut from your right to your left. Cut-
ting on left side of the shield will
throw debris away from the operator.
• Use only in daylight or good artificial
light.
• Use only for jobs explained in this
manual.
TRANSPORTING AND STORAGE
• Allow engine to cool; secure unit be-
fore storing or transporting in vehicle.
• Empty the fuel tank before storing or
transporting the unit. Use up fuel left
in the carburetor by starting the en-
gine and letting it run until it stops.

• Storeunitandfuelinareawhere
fuelvaporscannotreachsparksor
openflamesfromwaterheaters,
electricmotorsorswitches,fur-
naces,etc.
• Storeunitsolinelimiterbladecan-
notaccidentallycauseinjury.The
unitcanbehungbythetube.
• Storeunitoutofreachofchildren.
SAFETYNOTICE:Exposuretovibra-
tionsthroughprolongeduseofgaso-
linepoweredhandtoolscouldcause
bloodvesselornervedamageinthe
fingers,hands,andjointsofpeople
pronetocirculationdisordersorab-
normalswellings.Prolongedusein
coldweatherhasbeenlinkedtoblood
vesseldamageinotherwisehealthy
people.Ifsymptomsoccursuchas
numbness,pain,lossofstrength,
changeinskincolorortexture,orloss
offeelinginthefingers,hands,or
joints,discontinuetheuseofthistool
andseekmedicalattention.Ananti-
vibrationsystemdoesnotguarantee
theavoidanceoftheseproblems.Us-
erswhooperatepowertoolsonacon-
tinualandregularbasismustmonitor
closelytheirphysicalconditionand
theconditionofthistool.
SPECIALNOTICE:Thisunitis
equippedwithatemperaturelimiting
mufflerandsparkarrestingscreen
whichmeetstherequirementsofCali-
forniaCodes4442and4443.AllU.S.
forestlandandthestatesofCalifornia,
Idaho,Maine,Minnesota,NewJersey,
Oregon,andWashingtonrequireby
lawthatmanyinternalcombustionen-
ginesbeequippedwithasparkarrest-
ingscreen.Ifyouoperateinalocale
wheresuchregulationsexist,youare
legallyresponsibleformaintainingthe
operatingconditionoftheseparts.
Failuretodosoisaviolationofthe
law.Fornormalhomeowneruse,the
mufflerandsparkarrestingscreenwill
notrequireanyservice.After50
hoursofuse,werecommendthatyour
mufflerbeservicedorreplacedby
yourSearsServiceCenter.
CARTONCONTENTS
Checkcartoncontentsagainstthefol-
lowinglist.
Model 358.795540
• Trimmer
• Shield
• Wing Nut (screwed onto shield)
• Assist Handle (with bolt and knob)
• Container of Oil
Examine parts for damage. Do not
use damaged parts.
NOTE: If you need assistance or find
parts missing or damaged, call
1-800-235-5878.
It is normal for the fuel filter to rattle in
the empty fuel tank.
Finding fuel or oil residue on muffler is
normal due to carburetor adjustments
and testing done by the manufacturer.
ASSEMBLY
,_WARNING: If received as-
sembled, repeat all steps to ensure
your unit is properly assembled and all
fasteners are secure.
Be sure to attach the assist handle to
the unit before you attach the shield.
ATTACHING THE HANDLE
(some units are already assembled)
1. Assemble handle to the unit as
shown; make sure bottom of han-
dle is seated in the groove in the
trigger housing.
I
NOTE: Knob must be assembled on
the right hand side of the unit as
shown in the illustration.
2. Make sure the bolt is seated in the
hex-shaped hole in the handle.
3. Pivot the handle to a comfortable
position.
4. Tighten knob securely.
ATTACHING SHIELD
_,WARNING: The shield must be
properly installed. The shield provides
partial protection from the risk of thrown
objects to the operator and others and
is equipped with a line limiter blade
which cuts excess line to the proper
length. The line limiter blade (on under-
side of shield) is sharp and can cut you.
4

Forproperorientationofshield,see
KNOWYOURTRIMMERillustrationinOP-
ERATIONsection.
1. Removewingnutfromshield.
2. Insertbracketintoslotasshown.
3. Pivotshielduntilboltpasses
throughholeinbracket.
4. Securelytightenwingnutontobolt.
Shield _'.X/_ I°t
__% Bracket
KNOW YOUR TRIMMER
READ THiS iNSTRUCTiON MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT, Compare the illustrations with your unit to familiarize yourself with the location
of the various controls and adjustments. Save this manual for future reference.
Assist Handle
Muffler
Primer Bulb
Fuel Mix
Fill Cap
ON/OFF SWITCH
The ON/OFF switch is used to stop en-
gine. To stop the engine, move switch
to the OFF position.
PRIMER BULB
The PRIMER BULB removes air from
the carburetor and fuel lines and fills
them with fuel. This allows you to start
the engine with fewer pulls on the
starter rope. Activate the primer bulb
by pressing it and allowing it to return
to its original form.
Tube
J
Trimmer
Head
Edge
Guide
Shield i_
Line Limiter
Blade
CHOKE
The CHOKE helps to supply fuel to tile
engine to aid in cold starting. Activate
the choke by moving the choke lever to
the FULL CHOKE position. After the en-
gine attempts to start, move the choke
lever to the HALFCHOKE position. Once
engine has started, move the choke le-
ver to the OFF CHOKE position.
EDGE GUIDE
The EDGE GUIDE protects the unit
from contacting the ground during
edging.
BEFORE STARTING ENGINE
_iWARNING: Be sure to read
the fuel information in the safety rules
before you begin. Ifyou do not
understand the safety rules, do not
attempt to fuel your unit. Call
1-800-235-5878.
FUELING ENGINE
_bWARNING: Remove fuel cap
slowly when refueling.
This engine is certified to operate on
unleaded gasoline. Before operation,
gasoline must be mixed with a good
quality synthetic 2-cycle air-cooled
5

engineoil.WerecommendCraftsman
brandsyntheticoil.Mixgasolineandoil
ataratioof40:1.A40:1ratiois
obtainedbymixing3.2ouncesofoil
with1gallonofunleadedgasoline.
Includedwiththistrimmerisa3.2
ouncecontainerofoil.Pourtheentire
contentsofthiscontainerinto1gallon
ofgasolinetoachievetheproperfuel
mixture.DONOTUSEautomotiveoilor
boatoil.Theseoilswillcauseengine
damage.Whenmixingfuel,follow
instructionsprintedoncontainer.
Onceoilisaddedtogasoline,shake
containermomentarilytoassurethatthe
fuelisthoroughlymixed.Alwaysread
andfollowthesafetyrulesrelatingto
fuelbeforefuelingyourunit.
IMPORTANT
Experience indicates that alcohol
blended fuels (called gasohol or using
ethanol or methanol) can attract mois-
ture which leads to separation and
formation of acids during storage.
Acidic gas can damage the fuel sys-
tem of an engine while in storage.
To avoid engine problems, empty the
fuel system before storage for 30 days
or longer. Drain the gas tank, start the
engine and let it run until the fuel lines
and carburetor are empty. Use fresh
fuel next season.
Never use engine or carburetor clean-
er products in the fuel tank or perma-
nent damage may occur.
See the STORAGE section for addition-
al information.
HOW TO STOP YOUR UNIT
• To stop the engine, move the ON/
OFF switch to the OFF position.
• If engine does not stop, move choke
to the FULL CHOKE position.
Choke Lever
Engine
ON/OFF
HOW TO START YOUR UNIT
_WARNING: The trimmer head
will turn while starting the engine.
Avoid any contact with the muffler. A
hot muffler can cause serious burns.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
1. Set unit on a flat surface.
2. Move ON/OFF switch to the ON posi-
tion.
3. Slowly press the primer bulb 6
times.
4. Move choke lever to FULLCHOKE
position.
5. Squeeze the throttle trigger fully and
hold through all remaining steps.
Choke
,- Lever
Primer
Bulb
6. Pull starter rope handle sharply until
engine sounds as it if is trying to
start, but do not pull rope more than
6 times.
7. As soon as engine sounds as if it is
trying to start, move choke lever to
the HALFCHOKE position.
8. Pull starter rope sharply until engine
runs, but no more than 6 pulls.
NOTE: Ifthe engine doesn't start
after 6 pulls (at the HALF CHOKE
position), move the choke lever to
the FULL CHOKE position and press
the primer bulb 6 times. Squeeze
and hold the throttle trigger and pull
the starter rope 2 more times. Move
the choke lever to the HALF CHOKE
position and pull the starter rope un-
til the engine runs, but no more than
6 pulls. Ifthe engine still doesn't
start, it is probably flooded. Proceed
to STARTINGA FLOODED ENGINE.
9. Once the engine starts, allow it to
run 10 seconds, then move the
choke lever to the OFF CHOKE
position. Allow the unit to run for
30 more seconds at OFF CHOKE
before releasing the throttle trigger.
NOTE: If engine dies with the
choke lever in the OFF CHOKE
position, move the choke lever to
the HALF CHOKE position and pull
the rope until engine runs, but no
more than 6 pulls.

STARTING A WARM ENGINE
1. Move ON/OFF switch to the ON posi-
tion.
2. Move the choke lever to the HALF
CHOKE position.
3= Squeeze and hold the throttle trig-
ger. Keep throttle trigger fully
squeezed until the engine runs
smoothly.
4. Pull starter rope sharply until engine
runs, but no more than 5 pulls.
5. Allow engine to run 15 seconds,
then move the choke lever to the
OFF CHOKE position.
NOTE: If engine has not started, pull
starter rope 5 more pulls. If engine still
does not run, it is probably flooded.
STARTING A FLOODED ENGINE
Flooded engines can be started by
placing the choke lever in the OFF
CHOKE position; then, pull the rope to
clear the engine of excess fuel. This
could require pulling the starter handle
many times depending on how badly
the unit is flooded.
If the unit still doesn't start, refer to
TROUBLESHOOTING TABLE or call
1-800-235-5878.
OPERATING INSTRUCTIONS
OPERATING POSITION
ALWAYS WEAR:_
Long Pants --_'_/_
Heavy Shoes .._._i
Eye Protection
Cut from your right to your left.
,it
dt_WARNING: Always wear eye
protection. Never lean over the trimmer
head. Rocks or debris can ricochet or
be thrown into eyes and face and
cause blindness or other serious injury.
When operating unit, stand as shown
and check for the following:
• Wear eye protection and heavy
clothing.
• Hold trigger handle with right hand
and assist handle with left hand.
• Keep unit below waist level.
• Cut only from your right to your left to
ensure debris is thrown away from
you. Without bending over, keep line
near and parallel to the ground and
not crowded into material being cut.
Do not run the engine at a higher
speed than necessary. The cutting
line will cut efficiently when the engine
is run at less than full throttle. At lower
speeds, there is less engine noise and
vibration. The cutting line will last
longer and will be less likely to "weld"
onto the spool.
Always release the throttle trigger and
allow the engine to return to idle
speed when not cutting.
To stop engine:
• Release the throttle trigger.
• Move the ON/OFF switch to the OFF
position.
TWIST AND EDGE
The Twist and Edge feature allows for
easy edging of sidewalks, patios,
driveways, etc.
1. Pull the tab toward the engine.
2. Twist the tube to the edging posi-
tion; release tab.
TRIMMER LINE ADVANCE
The cutting head advances line au-
tomatically. Do not tap head on the
ground to advance line. This may
break parts and cause cutting head to
malfunction.
Upon unit start up, the line will advance
automatically to the correct cutting path
length.
Always keep the shield in place when
the tool is being operated=
,IO_,WARNING: Use only 0.080" (2
mm) diameter round line. Other
sizes and shapes of line will not ad-
vance properly and will result in im-
proper cutting head function or can
cause serious injury. Do not use other
materials such as wire, string, rope,
etc. Wire can break off during cutting
and become a dangerous missile that
can cause serious injury.
CUTTING METHODS
_,WARNING: Use minimum speed
and do not crowd the line when cutting
around hard objects (rock, gravel, fence
posts, etc.), which can damage the trim-
mer head, become entangled in the
line, or be thrown causing a serious
hazard=
7

• Thetipofthelinedoesthecutting.
Youwillachievethebestperformance
andminimumlinewearbynotcrowd-
ingthelineintocuttingarea.Theright
andwrongwaysareshowninthefol-
lowingillustration.
TipoftheLine LineCrowdedInto
DoesTheCutting WorkArea
I
Right Wrong
• The line will easily remove grass
and weeds from around walls,
fences, trees and flower beds, but it
also can cut the tender bark of trees
or shrubs and scar fences.
• For trimming or scalping, use less
than full throttle to increase line life
and decrease head wear, especially:
• During light duty cutting.
• Near objects around which the line
can wrap such as small posts,
trees or fence wire.
• For mowing or sweeping, use full
throttle for a good clean job.
TRIMMING - Hold the bottom of the
trimmer head about 3 in. (8 cm) above
the ground and at an angle. Allow only
the tip of the line to make contact. Do
not force trimmer line into work area.
Trimming _ 1t
SCALPING - The scalping technique
removes unwanted vegetation. Hold
the bottom of the trimmer head about
3 in. (8 cm) above the ground and at
an angle. Allow the tip of the line to
strike the ground around trees, posts,
monuments, etc. This technique in-
creases line wear.
Scalping 3in. (8 cm)
Above Ground
JL
MOWING - Your trimmer is ideal for
mowing in places conventional lawn
mowers cannot reach. In the mowing
position, keep the line parallel to the
ground. Avoid pressing the head into
the ground as this can scalp the
ground and damage the tool.
""n°))
SWEEPING - The fanning action of
rotating line can be used for a quick
and easy clean up. Keep line parallel
to and above the surfaces being
swept and move the tool from side to
side.
Sweeping _ .....
EDGING - Adjust trimmer to the edg-
ing position (see "RNIST AND EDGE
section). Allow only the tip of the line
to make contact. Do not force trimmer
line into work area.
Edging __

MAINTENANCE SCHEDULE
_t WARNING: Disconnect the spark plug
except for carburetor adjustments.
CARE & MAINTENANCE TASK
Check for loose fasteners and parts
Check for damaged or worn parts
Inspect and clean unit and decals
Clean air filter
Inspect muffler and spark arresting screen
Replace spark plug
before performing maintenance
WHEN TO PERFORM
Before each use
Before each use
After each use
Every 5 hours of operation
Every 50 hours of operation
Yearly
GENERAL RECOMMEN DATIONS
The warranty on this unit does not
cover items that have been subjected
to operator abuse or negligence. To
receive full value from the warranty,
the operator must maintain unit as
instructed in this manual. Various ad-
justments will need to be made peri-
odically to properly maintain your unit.
CHECK FOR LOOSE
FASTENERS AND PARTS
• Spark Plug Boot
• Air Filter
• Housing Screws
• Assist Handle Screws
• Debris Shield
CHECK FOR DAMAGED OR
WORN PARTS
Contact Sears Service Center for re-
placement of damaged or worn parts.
• ON/OFF Switch - Ensure ON/OFF
switch functions properly by moving
the switch to the OFF position. Make
sure engine stops; then restart en-
gine and continue.
• Fuel Tank - Discontinue use of unit
if fuel tank shows signs of damage
or leaks.
• Debris Shield - Discontinue use of
unit if debris shield is damaged.
INSPECT AND CLEAN UNIT AND
DECALS
• After each use, inspect complete
unit for loose or damaged parts.
Clean the unit and decals using a
damp cloth with a mild detergent.
• Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
A dirty air filter decreases engine per-
formance and increases fuel con-
sumption and harmful emissions. Al-
ways clean after every 5 hours of
operation.
1. Clean the cover and the area
around it to keep dirt from falling into
the carburetor chamber when the
cover is removed.
2. Remove parts as illustrated.
NOTE: To avoid creating a fire hazard
or producing harmful evaporative
emissions, do not clean filter in gaso-
line or other flammable solvent.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Add a few drops of oil to the filter;
squeeze the filter to distribute oil.
6. Replace parts.
_Filter Screws
Cover
REPLACE SPARK PLUG
Replace the spark plug each year to
ensure the engine starts easier and
runs better. Set spark plug gap at
0.025 in. Ignition timing is fixed and
nonadjustable.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder
and discard.
3. Replace with Champion RCJ-6Y
spark plug and tighten with a 3/4 in.
socket wrench (10-12 ft.-Ibs).
4. Reinstall the spark plug boot.

LINE REPLACEMENT
Pre-wound spools offer the most con-
venient method for replacing line and
ensuring optimum performance.
• Replacement spools are color-
coded to ensure use of the correct
spool with your unit. Be sure to use
the same color spool as the existing
spool.
NOTE: Always clear dirt and debris
from cutting head components when
performing any type of maintenance.
• Hold spool and unscrew cap by turn-
ing in the direction shown on top of
the cap.
• Remove line guide ring and spool.
Line guide ring
X_j _J_ Spool
Use a pre-wound spool or refill spool
with line. If using a pre-wound spool,
remove tape strip from line and spool.
REFILLING THE SPOOL WITH LINE
_WARNING: Use only 0.080
inch (2 mm) diameter round line.
Other sizes and shapes of line will not
advance properly and will result in im-
proper cutting head function or can
cause serious injury. Do not use other
materials such as wire, string, rope,
etc. Wire can break off during cutting
and become a dangerous missile that
can cause serious injury.
1. Cut a length of 80 feet of 0.080 inch
(2 mm) diameter round Craftsman
brand line.
Spool
2. Insert one end of line into center
cavity of empty spool. Ensure line
will feed into spool in the direction
shown on the spool (counterclock-
wise).
3. Continue feeding line into spool,
leaving 4 - 6 inches (10 - 15 cm)
unwound from center of spool.
INSTALLING SPOOL WITH LINE
1. Install replacement spool.
2. Thread line through line guide ring.
Line through guide ring _,
/C(
\t s,et
Replacement Spool
3. Rest guide ring on spool and place
line through slot. Allow line to ex-
tend 4 - 6 inches (10 - 15 cm) from
center of spool.
4. Ensure line remains in slot while
screwing cap on to the shaft. Only
tighten cap hand tight!
CARBURETOR ADJUSTMENT
,_kWARNING: The trimmer head
will be spinning during most of this
procedure. Wear your protective
equipment and observe all safety pre-
cautions. After making mixture adjust-
ments, recheck idle speed.
Carburetor adjustment is critical and if
done improperly can permanently
damage the engine as well as the car-
buretor. If you require further assis-
tance or are unsure about performing
this procedure, call our customer as-
sistance help line at 1-800-235-5878.
Old fuel, a dirty air filter, a dirty fuel fil-
ter, or flooding may give the impres-
sion of an improperly adjusted carbu-
retor. Check these conditions before
adjusting the carburetor.
The carburetor has been carefully set
at the factory. Adjustments may be
necessary if you notice any of the fol-
lowing conditions:
• Engine will not idle. See iDLE SPEED
under adjusting procedure.
• Engine dies or hesitates instead of
accelerating. See ACCELERATION
CHECK under adjusting procedure.
10