Creative Access Solutions HD / Skylink User manual

1
Rev 7/15
External Wireless Module
For
HD / Skylink® Receiver
Programming the remote (LCD wall control with menu):
1. On the wall control, press MENU.
2. Highlight PROGRAM and select it.
3. Highlight REMOTE and select it.
4. Insert the program jumper into the remote connector.
5. Once the remote transmitter has been learned by the opener, you
will hear a series of clicks from the motor unit and the lights in the
opener (if installed) will flash indicating successful learning of the
remote. You can now unplug the program jumper.
6. Press the select button on the wall control to save the setting and
exit out to the main screen.
7. Plug the remote connector into the back of the HD receiver and
test using your bike’s high beam switch or other transmitter
paired to the HD receiver.
If your wall control doesn’t have an LCD menu or the steps above don’t
work, then proceed to the next page.

2
Rev 7/15
Preparing the module for your opener
As shipped, the module is set for use with a Security+ 2.0 opener
(yellow antenna wires and round yellow learn button). If your opener is
different, you will need to prepare the module for your opener. This
sets the frequency and coding to be compatible with your opener.
You'll need to remove the two screws on the back of the wireless
module and open the back cover. Orient the module with the
red/black wires toward the top. The small button that the wires are
attached to is the "Remote Control Button" that you will press when
instructed to do so below. The small white button that is mounted
sideways in the lower right corner (identified by “SW5” on the circuit
board)is the "Program Button". Note that it is pressed in from the side.
The following steps prepare your module for your opener:
1 - Press and hold the Program Button on the wireless module until the
LED on the front of the module turns on, then release it.
2 - Press and release the Remote Control Button (the top button with
the red/black wires connected to it) the number of times that
correspond to the garage door opener type (Refer to the table below).
3 - To exit programming mode, press either of the two other black
buttons (NOT the top button). The LED should go out.
# of Presses
Garage Door Opener Type
1
Security+ 2.0 (Yellow Learn Button)
2
315MHz Security+ (Purple Learn Button)
3
390MHz Security+ (Red/Orange Learn Button)
4
390MHz Billion Code (Green Learn Button)

3
Rev 7/15
Programming the remote (from the motor unit):
1. Locate the LEARN button on the garage door opener (motor unit).
2. Press and immediately release the LEARN button. The LEARN LED
will glow steady for 30 seconds. Within 30 seconds…
3. Insert the program jumper into the remote connector.
4. Remove the jumper when the garage door opener lights blink or
two clicks are heard from the motor unit.
If the instructions above don’t work for your model, then follow your
opener’s instruction manual for the procedure to add a remote. When
the instructions tell you to press the button on the remote, simply
insert the program jumper into the remote connector (and remove it
when instructed to release the button). If you lose your jumper, you
can use a small paper clip straightened, and bent into a U shape to
insert into the connector. Alternatively, you can open the module and
press the button closest to the red/black wires (follow directions on
next page top open the module).
If you no longer have your opener’s instructions, or are having
trouble programming the remote, send an email to
[e-mail] and be sure to include your
opener’s make and model number.

4
Rev 7/15
Battery Replacement:
The remote module contains a CR2032 lithium battery which should
last up to 5 years. If you find that the remote does not reliably operate
the opener, try replacing the battery:
1. Unplug the remote module from the back of the receiver.
2. Remove the two screws and carefully open the back.
3. Replace the battery with a 3V CR2032 coin cell battery.
4. Replace the back, taking care not to pinch any wires.
5. Plug the connector into the back of the receiver.