Creative Play TPH110 User manual

REF: TPH110
pg 1 of 14 18.06.2019
TPH110 - TIMBER PLAYHOUSE (RAISED)
Installation Instructions

REF: TPH110
pg 2 of 14 18.06.2019
TPH110 - TIMBER PLAYHOUSE (RAISED)
Installation Instructions
UPRIGHT TIMBERS
HORIZONTAL TIMBERS
TPH110 - H2
TPH110 - H1
TPH110 - U1R
TPH110 - U1L TPH110 - U2L
TPH110 - U2R
TPH110 - U2R
TPH110 - U2L
TPH110 - U1L
TPH110 - U1R

REF: TPH110
pg 3 of 14 18.06.2019
TPH110 - TIMBER PLAYHOUSE (RAISED)
Installation Instructions
ROOF TIMBERS
SLAT/CLADDING TIMBERS
R1
R2
R2
RT1
RT1
RT1
RT1
RT2
RT2
RT3
R
RT
= ROOF TIMBERS
= ROOF TRIM
TPH110 - S2
TPH110 - S3
x10
x20

REF: TPH110
pg 4 of 14 18.06.2019
PARTS REQUIREDPARTS REQUIRED
97.M8X80CSK
x128
x8
102003-01 - M12
ROOF PRE-ASSEMBLED PANELS
x2 x1
STAIR ASSEMBLY
x6
97.M8X120CSK
x8
656.M12
x8
274.M12X180
x18
97.M6X180CSK
x2
HEX FLOOR PANEL

REF: TPH110
pg 5 of 14 18.06.2019
FOUNDATION DETAILS
U1R
U1R
U2R
U2R
U2L
U2L
U1L
U1L
SOILPOST FGL CONCRETE

REF: TPH110
pg 6 of 14 18.06.2019
SURFACING DETAILS
= MINIMUM SPACE
= SURFACE AREA

REF: TPH110
pg 7 of 14 18.06.2019
INSTALLATION INSTRUCTIONS
1POSITION UPRIGHT TIMBERS ACCORDING TO GROUNDPLAN
ENSURING U2L & U2R TIMBER COUNTERSINKS ARE FACING INWARD AND U1L & U1R FACE OUTWARDS
2BOLT H2 TIMBERS TO UPRIGHTS
USING 274.M12X180 / 656.M12 / 102003-01-M12
TPH110 - U1R
TPH110 - U1L TPH110 - U2L
TPH110 - U2R
TPH110 - U2R
TPH110 - U2L
TPH110 - U1R
TPH110 - U1L
= INWARD
= OUTWARD
NOTES:
ENSURE CUP SQUARE SECTION SITS IN THE
COUNTERSINK

REF: TPH110
pg 8 of 14 18.06.2019
INSTALLATION INSTRUCTIONS
3SLOT H1 TIMBERS INTO H2 HALF LAP CUT OUTS
TO BE SCREWED TOGETHER WHEN HEXA GRIP IS ATTACHED
4ATTACH HEXA GRIP FLOOR PANELS
USING M8X80MM WOOD SCREWS

REF: TPH110
pg 9 of 14 18.06.2019
INSTALLATION INSTRUCTIONS
5ATTACH PRE-ASSEMBLED ROOF PANELS TO R1 RIDGE BEAM TIMBER
USING M8X120MM & M8X180MM WOOD SCREWS AS SHOWN BELOW
6ENSURE ROOF PANELS ARE ASSEMBLED AS HIGHLIGHTED BELOW
USING M8X120MM & M8X180 WOOD SCREWS
NOTES:
ENSURE RIDGE BEAM IS POSITIONED AS
SHOWN (RIGHT)
USE ACRO PROP TO SET BEAM AT CORRECT
HEIGHT (1890MM) FROM TOP OF HEX FLOOR
TO UNDERSIDE OF RIDGE BEAM (R1)
R1
ROOF ASSEMBLY
NOTES:
SCREW THROUGH THE ROOF
ASSEMBLY INTO RIDGE BEAM
(120MM SCREWS)
SCREW THROUGH UPRIGHTS INTO
ROOF PANEL ASSEMBLY FROM
INSIDE (180MM SCREWS)
ENSURE 180MM SCREWS DO NOT
GO ALL THE WAY THROUGH BOTH
90X90 TIMBERS
PTO ...

REF: TPH110
pg 10 of 14 18.06.2019
INSTALLATION INSTRUCTIONS
7ATTACH R2 TIMBERS
USING M8X180MM WOOD SCREWS
NOTES:
ENSURE UPRIGHT SCREWS ARE SCREWED
IN FROM THE INSIDE OF THE PLAYHOUSE AS
SHOWN
NOTES:
ENSURE TIMBERS ARE SCREWED IN
FROM THE INSIDE OF THE PLAYHOUSE -
SCREW HEADS ON INSIDE

REF: TPH110
pg 11 of 14 18.06.2019
INSTALLATION INSTRUCTIONS
8ATTACH ROOF TRIM PIECES (RT1, RT2 & RT3) AS SHOWN BELOW
READ NOTES BELOW AND USE M8X80MM WOOD SCREWS TO SECURE
NOTES:
1. ATTACH RT1 TIMBERS (ENSURE TOP FACE
OF RT1 TIMBER IS FLUSH WITH TOP FACE OF
RIDGE BEAM (R1) - (3 PER RT1 TRIM)
2. ATTACH RT3 TIMBER TO RIDGE BEAM (R1)
(3 SCREWS)
3. ATTACH RT2 ‘COVERS’ TO RT1 TRIM &
INTO ROOF ASSEMBLY (3 SCREWS)
ENSURE SCREWS ARE UNIFORM/
INLINE AS SHOWN TO RIGHT ...
R1

REF: TPH110
pg 12 of 14 18.06.2019
INSTALLATION INSTRUCTIONS
9ATTACH TPH110 - S2 TIMBERS TO UPRIGHTS SHOWN (U1L & U1R OUTER TIMBERS)
USING M8X80MM WOOD SCREWS, 5 TIMBER SLATS PER SIDE, 4 SCREWS PER TIMBER
10 ATTACH TPH110 - S1 TO FRONT AND BACK OF PLAYHOUSE
USING M8X80MM WOOD SCREWS, 5 TIMBER SLATS PER SIDE, 4 SCREWS PER TIMBER
NOTES:
ENSURE S2 TIMBERS ARE FLUSH WITH
UPRIGHT TIMBERS AND 90 X90
TIMBERS UNDER HEX (SEE LEFT)
TPH110 - U1L TPH110 - U1R
NOTES:
ENSURE S1 TIMBER SLATS ARE FLUSH WITH S2
SLAT AND 90X90 FACES SHOWN BELOW

REF: TPH110
pg 13 of 14 18.06.2019
INSTALLATION INSTRUCTIONS
11 ATTACH TPH110 - US TIMBERS TO STAIR ASSEMBLY
USING M8X180MM & M8X120MM WOOD SCREWS - TOP SCREW = 180MM SCREW, BOTTOM = 120MM SCREW
12 SECURE THE STAIRS ASSEMBLIES INTO PLACE ON BOTH SIDES OF PLAYHOUSE
USING M8X80MM WOOD SCREWS ABOVE AND BELOW AS SHOWN
US
US
180MM SCREW
120MM SCREW
BELOW HEX
ABOVE HEX

REF: TPH110
pg 14 of 14 18.06.2019
ADDITIONAL DIMENSIONS