Creative Playthings LEXINGTON PLAY WALLS SC 909-800Q User manual

©Copyright 2001, Creative Playthings. Printed in USA.
19496-300 Rev E (03-20)
LEXINGTON PLAY WALLS
Page 1
• 1/2" Socket and Wrench
• Electric Drill
• Screwdriver or Screwdriver Tip for Electric Drill
• Tape Measure
MODEL # SC 909-800Q
ASSEMBLY MANUAL LEXINGTON PLAY WALLS
illustration #1
PARTS
A 1 Ea. 31526-102 End Wall Support - 2 x 4 x 59-1/2"
B 1 Ea. 50122-200 Hardware Bag - Lexington Play Walls
C 1 Ea. 31465-102 Side Wall Support - 2 x 4 x 83-1/4"
D 27 Ea. 31936-102 Wall Slat - 5/4 x 6 x 20"
SPECIAL NOTES
•If you also plan to install a play oor option, install the play oor rst. The wall slats will rest on the play oor boards.
•Any sandbox seats must be removed and will not be used with the play wall option.
•The play wall can not be used with the Lexington picnic table.
•The Safety Rail from your Lexington play set is used with this accessory. It does need to be removed.
Please review your original Lexington Assembly Manual and
your Owners Manual before assembly of your Play Wall.
108 Ea. 17020-115 Flat Head Wood Screw - #10 x 1-5/8"
4 Ea. 17002-206 Flat Washer - 5/16"
4 Ea. 15081-704 1" Hole Cap - Brown
4 Ea. 17036-1202 Lag Screw - 5/16 x 2-1/2"
TOOLS REQUIRED FOR ASSEMBLY

ASSEMBLY INSTRUCTIONS
LEXINGTON PLAY WALLS
Page 2 ©Copyright 2001, Creative Playthings. Printed in USA.
19496-300 Rev E (03-20)
LEXINGTON PLAY WALLS
PLEASE CONSULT YOUR ORIGINAL GYM ASSEMBLY MANUAL FOR
MAINTENANCE AND SAFETY INSTRUCTIONS
illustration #2
C
Corner Post
Safety Rail
C
A
STEP 1 – Side Wall Support:
The Side Wall Support (C) is Fastened to the Corner Posts
opposite the Safety Rail. Fasten the Side Wall Support
(C) to the Corner Posts with two 5/16 x 2-1/2" Lag Screw
Assemblies.
illustration #3
illustration #4
STEP 2 – End Wall Support:
Before attaching the End Wall Support (A) to the Corner
Posts, the holes for the Lag Screws must be drilled. Align
the top of the End Wall Support (A) with the top of the
Safety Rail, and Side Wall Support (C). Mark the back of
the Corner Posts, opposite the Slide, at each hole location
on the End Wall Support (A). Drill a hole at each mark 3/16"
Dia. to a depth of 2".
Fasten the End Wall Support (A) to the Corner Posts with
two 5/16 x 2-1/2" Lag Screw Assemblies.
Corner Post
STEP 3 – Wall Slats:
Fasten seven Wall Slats (D) to the End Wall Support (A) and
Sandbox End. Evenly distribute the Wall Slats (D) between
the Corner Posts, the spacing will be approx. 1-11/16".
Fasten each Wall Slat (D) with four #10 x 1-5/8" Screws.
Fasten ten Wall Slats (D) to the Side Wall Support (C) and
Sandbox Side. Evenly distribute the Wall Slats (D) between
the Corner Posts, the spacing will be approx. 2-1/4". Fasten
each Wall Slat (D) with four #10 x 1-5/8" Screws.
Fasten ten Wall Slats (D) to the Safety Rail and Sandbox
Side. Evenly distribute the Wall Slats (D) between the
Corner Posts, the spacing will be approx. 2-1/4". Fasten
each Wall Slat (D) with four #10 x 1-5/8" Flat Head Screws.
Safety Rail
Corner Post
Corner Post
Sandbox Side
Safety Rail
Sandbox Side Sandbox
End
CD
Corner Post
DA
D