Creative Playthings Lexington Premium Pack 8 User manual

LEXINGTON PREMIUM PACK 8
LEXI9WPP8-100 Rev A (04-18)
© Copyright 2018, Creative Playthings
CHILDHOOD STARTS HERE
LEXI9WPP8
L P P 
Cartons for this Play Set:
1 63007-421 Lexington Gym 1 (Hardware)
1 63007-422 Lexington Gym 2
1 63007-423 Lexington Gym 3
1 63007-445 Lexington Roof (Hdwre & Instr)
1 SH946-102 Access Ladder
1 AG942-400 Access Ladder Handles (Hdwre & Instr)
1 63058-202 4 Position Swing Beam
1 63060-222 9ft Swing Beam Legs (Hdwre & Instr)
1 50546-777 3 Swings, 1 Trapeze
1 15166-400 10 ft. Super Wave Slide
1 AG943-400 Slide Handle (Hdwre & Instr)
1 AH201-102Q Rock Climber (Hdwre & Instr)
1 SC909-800Q Lexington Play Walls (Hdwre & Instr)
1 SC910-800Q Lexington Play Floor (Hdwre & Instr)
1 63081-102 Ice Cream Stand (Hdwre & Instr)
1 SM964-402 Gable Fans (Hdwre & Instr)
1 SM963-402 Dormer (Hdwre & Instr)
1 AA917-603 Fireman's Pole (Hdwre & Instr)
• Start by assembling the Lexington tower. Instructions and hard-
ware are in the cartons noted at left.
• Wait to install the Access Ladder, Slide, and Wall Slats until after
the rest of the play set is complete.
• Lexington step 7. Do not install the safety rail. It will be used for
the Play Walls.
• Lexington step 8. Do not install the angle brace mounted to the
back platform end nearest the swings. It will interfere with the
chalkboard.
• Lexington step 15. No Swing Mount is needed.
After completing the tower except Access Ladder, Slide, and Wall
Slats:
• Using a ladder, install the Dormer (SM963-402) in the position
shown. Ladder access may be obstructed by later installations.
• Install the Gable Fans (SM964-402).
• Install the 9ft Swing Beam. Instructions are in carton 63060-222.
The components of this gym can be combined with others to create different play sets.
This is the best order of assembly to create this specic set.
Read this sheet and all instructions included with the different parts before assembly.
See the Instructions and Owner's Manual included in carton 63007-445 for important
safety information.
Dimensions of assembled package:
19' 4" wide x 16' 6" deep x 11' 6" tall

© Copyright 2018, Creative Playthings
LEXINGTON PREMIUM PACK 8
LEXI9WPP8-100 Rev A (04-18) Page 2
Gable Fan
Ice Cream
Stand
Swing Beam
Dormer
Sliding
pole
Rock Climbing
Wall
Play Walls
• Install the Play Floor (SC910-800Q).
• Install the Play Walls (SC909-800Q) on front and swing
side of the tower.
• Install the Ice Cream Stand (63081-102) on the back of the
tower.
• Install the Rock Climbing Wall (AH201-102Q) in the pos-
tion shown.
• Place the access ladder and slide as shown in the picture
on the preceding page. Check spacing.
• Fasten access brackets to the inside of the ladder rails.
Secure the access ladder using the method shown in step
17 of the Lexington instructions.
• Fasten the Access Ladder Handles (AG942-400) to the
Access Ladder.
• Install the slide mount and slide using the method shown
in steps 23 and 24 of the Lexington instructions.
• Install wall slats in the postions shown on the front page,
using the methods from the Lexington instructions. Gaps
must be narrower than 3-1/2" or wider than 9" to prevent
potential head entrapment.
• Mount one hand grip to the entrance wall slat between the
ladder and the slide. Mount the other hand grip to the adja-
cent post at the same height, using 1/4 x 1-1/2" lag screws
and 1/4" at washers. Drill 3/16" diameter pilot holes for
the lag screws.
• Mount the Slide Handle (AG943-400) above the Super
Wave Slide.
• Install the sliding pole (AA917-603) in the position shown.
• Double-check all fasteners are secure and all recessed
hardware is covered by hole caps.