CREE LIGHTING Stylus Series User manual

Stylus Series
LED Ambient Luminaire
Recessed Mount
1 of 8 LPN00644X0007A0_A
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
Installation Instructions are divided into
5 sections:
1. On Grid Mounting - Individual Recessed
Mounting
2. On Grid Mounting - Continuous Row Recessed
Mounting
3. Off Grid Mounting (Hard Ceiling) - Individual
Recessed Mounting
4. Off Grid Mounting (Hard Ceiling) - Continuous
Row Recessed Mounting
5. Electrical Connections
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed
including the following:
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
1. DANGER- Risk of shock- Disconnect power before installation.
DANGER – Risque de choc – Couper l’alimentation avant l’installation.
2. This luminaire must be installed in accordance with the NEC or your local
electrical code. If you are not familiar with these codes and requirements,
consult a qualied electrician.
Ce produit doit être installé conformément à NEC ou votre code électrique
local. Si vous n’êtes pas familier avec ces codes et ces exigences, veuillez
contacter un électricien qualié.
3. SUITABLE FOR CONTINUOUS ROW MOUNTING.
PEUT ÊTRE MONTÉ EN RANGÉE CONTINUE.
4. Suitable for Damp Locations.
Convient aux emplacements humides.
5. MIN. 90C SUPPLY CONDUCTORS.
LES FILS D’ALIMENTATION 90C MIN.
6. INHERENTLY PROTECTED.
7. TYPE IC. VAPOR BARRIER MUST BE SUITABLE FOR 90C.
TYPE IC. LE PARE-VAPEUR DOIT CONVENIR POUR 90 °C.
PROTECTION INHERENTE.
8. Make sure the equipment is properly grounded.
9. Always de-energize the circuit and/or equipment before connecting to, disconnecting
from or servicing the equipment
SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE
ON GRID MOUNTING
1" T-bar
Flush Ceiling Tile
9/16" T-bar
Flush Ceiling Tile
Screw Slot
T-bar
1" T-bar
Tegular Tile
OFF GRID MOUNTING
Hard Ceiling
Flangeless
Hard Ceiling
Overlap Flange
NOTES:
• CAUTION - It is the installers responsibility to ensure that ceiling is structurally capable of supporting the weight of luminaire/luminaire row.
• Endcap kits and joining hardware are packaged separately for continuous rows.
• To Prevent Luminaire Row From Over-Current: By adding the input current of each luminaire section marked on the luminaire, the total current per
power feed must not exceed the maximum line wire amperage rating in the luminaire and the power feed cord/wire amperage rating whichever is
least.
9/16" T-bar
Tegular Tile

2 of 8 LPN00644X0007A0_A
SECTION 1:
ON GRID MOUNTING
INDIVIDUAL RECESSED MOUNTING
CAUTION: Ceiling contractor must provide an uninterrupted,
continuous rough opening utilizing tee grids spaced at 4" center to
center. Length of opening should be determined from Figure 3 on
next page. Tee grids must be secured to structure above to support
weight of luminaire.
CAUTION: Luminaires should be secured to structure above to
support weight of luminaire.
STEP 1:
Remove lens and upper LED/reflector tray and set aside in order of
run placement for reinstalling later. To remove lens, carefully slide
a plastic card or putty knife between the lens and extrusion towards
the end of the luminaire. Using the plastic card or putty knife, push
the lens inward until the lens comes free. See Figure 1 and 2.
STEP 2:
After removing the lens, remove the Philips head reflector screws,
remove the LED Reflector Tray, and disconnect the LED harness.
Set lens and LED Reflector tray aside. See Figure 1.
STEP 3:
Attach customer supplied support cables to luminaire and structure
above as shown in Figure 1:
STEP 4:
Using one of the 7/8” diameter holes on the end of the luminaire, install
customer supplied conduit and make electrical connections per
Section 5 “Electrical Connections”
STEP 5:
Reconnect LED harness. Replace LED trays and lens that was
removed in Step 1 & 2 above, ensure that no wires are pinched.
1
Support Cable
(Supplied By Others)
TO INSTALL:
Flexible Conduit
(Supplied By Others)
LED Tray
Lens
#10-18 X 1/4”
Phillips Head
Screws
2
Lens
Extrusion
Slide Plastic Card or
Putty Knife Here

3 of 8 LPN00644X0007A0_A
2’ FIXTURE
4’ FIXTURE
8’ FIXTURE
12’ FIXTURE
6’ FIXTURE
10’ FIXTURE
LUMINAIRE ROW LAYOUT: SINGLE UNIT 2'  12'
3
***NOTE: Plugged holes provided for conduit entry are located 2" from both ends of each luminaire.
***NOTE: Luminaires intended for Hard Off Grid Ceiling are to be installed with threaded rod to structure above ‘by others’ and should be installed
accordance with these instructions. Plugged holes for threaded rod attachment are located 4in from both ends of each luminaire.
23.25"
0.19" Endcap
Thickness
0.19"
47.25"
71.25"
95.25"
119.25"
143.25"
0.19" Endcap
Thickness
0.19" Endcap
Thickness
0.19" Endcap
Thickness
0.19" Endcap
Thickness
0.19" Endcap
Thickness
0.19" Endcap
Thickness
0.19" Endcap
Thickness
0.19" Endcap
Thickness
0.19" Endcap
Thickness
0.19" Endcap
Thickness

4 of 8 LPN00644X0007A0_A
SECTION 2: ON GRID MOUNTING  CONTINUOUS ROW RECESSED MOUNTING
CAUTION: Ceiling contractor must provide
an uninterrupted, continuous rough opening
utilizing tee grids spaced 4” center to center.
Length of opening should be determined from
Figure 7 on next page. Tee grids and luminaire
must be secured to structure above to support
weight of luminaire.
CAUTION: Do not attempt to assemble
luminaire rows on the ground and then lift
into position. This may create stress at the
connection points and may result in damage
and/or mechanical failure.
CAUTION: Do not connect power in a run until
all of run is installed, wire harnesses connected,
and luminaire joints completed.
STEP 1:
Remove lens and LED/reflector tray and set
aside in order of run placement for reinstalling
later. To remove lens, carefully slide a plastic
card or putty knife between the lens and
extrusion towards the end of the luminaire.
Using the plastic card or putty knife, push the
lens inward until the lens come free. After
removing the lens, remove the Philips head
reflector screws, remove the LED Reflector Tray,
and disconnect the LED harness. Set lens and
LED Reflector tray aside. See Figure 1 and 2.
STEP 2:
Locate and install End Cap Kits. Install End Cap
with (4) #6 screws from end cap kit. The end
cap has to be trimmed, the amount depends on
the run length. Each notch corresponds to the
successive Trim Length section in the chart on
the next page (See Figure 7). In order to install
the end cap on the male end of the luminaire,
replace the male joiner bracket with the female
joiner bracket and remove the alignment pins.
See Figure 4 and 6.
STEP 3:
Lay the first luminaire Right-Hand End
of the Row into the grid per Figure 7 grid
requirements.
STEP 4:
Position second luminaire in row such that it aligns
with joint end (male end) of first luminaire. Attach
using customer supplied hardware to structure
above. Connect the second luminaire to the first
luminaire as shown in Figure 5 and 6. Plug wire
harness together and push excess wire into
luminaire wiring chamber, ensure that wires are
not pinched.
STEP 5:
Push luminaires tightly together while making
sure the alignment pins slide into the interior
tracks of each luminaire and span the luminaire
joint. Secure joint by tightening supplied keps
locknuts on threaded studs of male joiner
bracket. Attach safety wires to luminaire safety
wire bracket and structure above as shown in
Figure 5 and 6.
STEP 6:
Continue to install and assemble row following
steps 1-5 above. Using one of the 7/8" dia.
holes on the End unit (Left-Hand End of Run)
luminaire, install conduit connector and make
electrical connections per Section 5 “Electrical
Connections”.
STEP 7:
Replace LED trays and lens that was removed in
Step 1 above, ensure that no wires are pinched.
4 5
6
End Cap
End Cap
LED Tray
Lens
Safety Wires
Safety Wires
(Supplied by Others)
Safety Wires Brackets
Alignment Pins
Male End
Female End
Male End
Female End
End Plate Cap (After
Trimming Has Been Done)
(4) #6 Screws
7/8" Plugged Hole
for Conduit Entry
5/8" Plugged Hole for
Threaded Rod Attachment
(Off-Grid Mounting ONLY)

5 of 8 LPN00644X0007A0_A
20’ FIXTURE
24’ FIXTURE
8’ UNIT
8’ UNIT
8’ UNIT
8’ UNIT
4’ UNIT
8’ UNIT
EXAMPLE 3 FIXTURE CONTINUOUS ROW
Continous Row Layout
4' 6' 8'
14
16
18
20
22
24
Units
End Cap
Kits
Feet
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
2.125
2.125
2.125
2.125
2.625
2.625
2.625
2.625
3.1875
3.1875
3.1875
3.1875
3.75
3.75
3.75
3.75
4.25
4.25
4.25
4.25
4.75
4.75
4.75
4.75
166.25
190.13
213.06
237.06
261.06
285.00
308.00
332.00
356.00
380.00
402.88
426.88
450.88
474.88
497.81
521.81
545.81
569.81
592.75
616.75
640.75
664.75
687.63
711.63
735.63
759.63
782.50
806.50
830.50
854.50
1
2
1
2
2
3
2
3
3
4
3
4
4
5
4
5
5
6
5
6
6
7
6
7
7
8
7
8
8
9
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
50
52
54
56
58
60
26
28
30
32
34
36
38
40
42
44
46
48
62
64
66
68
70
72
Trim Length
for Endcaps (in)
(For On Grid
Mounting ONLY)
Continous Row
Length (in)
End Cap to
End Cap
LUMINAIRE ROW LAYOUT: EXAMPLE OF A THREE UNIT 20'  24' (CAN BE MOUNTED IN OTHER CONFIGURATIONS)
7
86-7/8” 86-7/8"
38-7/8”
237-1/16" End Cap to End Cap
236-1/16" Aperture
284-5/8" Aperture
285-00" End Cap to End Cap
86-7/8" 86-7/8"86-7/8"
***NOTE: Plugged holes provided for conduit entry are located 2" from both
ends of each luminaire.
***NOTE: Luminaires intended for Hard Off Grid Ceiling are to be installed with
threaded rod to structure above ‘by others’ and should be installed accordance
with these instructions. Plugged holes for threaded rod attachment are located
4" from both ends of each luminaire.
End Plate (Before
Trimming Has Been Done)
Notches

6 of 8 LPN00644X0007A0_A
SECTION 3:
OFF GRID MOUNTING (HARD CEILING) 
INDIVIDUAL RECESSED MOUNTING
CAUTION: Ceiling contractor must provide an uninterrupted,
continuous rough opening. Dimensions of opening should be
determined using Figure 3 on page 3 and Figure 9.
CAUTION: Luminaires should be secured to structure above
using customer supplied threaded rods to support weight of
luminaire.
STEP 1:
Remove lens and LED/reflector tray and set aside in order
of run placement for reinstalling later. To remove lens,
carefully slide a plastic card or putty knife between the lens
and extrusion towards the end of the luminaire. Using the
plastic card or putty knife, push the lens inward until the
lens come free. After removing the lens, remove the Philips
head reflector screws, remove the LED Reflector Tray, and
disconnect the LED harness. Set lens and LED Reflector tray
aside. See Figure 2 and 8.
STEP 2:
Using one of the 7/8" dia. holes on the end of the fixture,
install conduit connector. See Figure 8.
STEP 3:
Install fixture from below into ceiling opening. Attach
customer supplied threaded rods to luminaire through 5/8"
mounting holes located on the top of the housing and to the
structure above as shown in Figure 8. Confirm that fixture is
pulled up firm to ceiling line.
STEP 4:
Make electrical connections per Section 5 “Electrical
Connections” to leads in wiring compartment.
STEP 5:
Reconnect LED harness. Replace LED trays and lens that
was removed in Step 1 above, ensure that no wires are
pinched.
STEP 6:
For Hard Ceiling, Overlap Flange Only:
Fill in Sheet Rock mud over tapered extruded flange until
smooth. See Figure 10.
9
4.25"
Ceiling opening width
for Flangeless
3.37"
Ceiling opening width
overlapping flange
8
Flexible Conduit
Supplied By Others Threaded Support Rods Supplied By Others
Support Nut
Supplied By Others
LED Tray
Lens
#10-18 X 1/4”
Phillips Head Screws
Sheetrock Mud
Supplied By Others
Sheetrock Mud
Supplied By Others
Threaded Support Rod
Supplied by Others
10

7 of 8 LPN00644X0007A0_A
SECTION 4:
OFF GRID MOUNTING (HARD CEILING) 
CONTINUOUS ROW RECESSED MOUNTING
CAUTION: Ceiling contractor must provide an uninterrupted, continuous
rough opening. Dimensions of opening should be determined using
Figure 7 on page 5 and Figure 9.
CAUTION: Luminaires should be secured to structure above to support
weight of luminaire.
CAUTION: Do not attempt to assemble luminaire rows on the ground
and then lift into position. This may create stress at the connection
points and may result in damage and/or mechanical failure.
CAUTION: Do not connect power in a run until all of run is installed,
wire harnesses connected, and luminaire joints completed.
STEP 1:
Remove lens and LED/reflector tray and set aside in order of run
placement for reinstalling later. To remove lens, carefully slide a plastic
card or putty knife between the lens and extrusion towards the end
of the luminaire. Using the plastic card or putty knife, push the lens
inward until the lens come free. After removing the lens, remove the
Philips head reflector screws, remove the LED Reflector Tray, and
disconnect the LED harness. Set lens and LED Reflector tray aside. See
Figure 2 and 6.
STEP 2:
Install the first luminaire (Right-Hand End of Run) from below into
ceiling opening. Attach customer supplied threaded rods to luminaire
through 5/8" mounting holes located on the top of the housing and to
the structure above as shown in Figure 7 and 8. Confirm that fixture
is pulled up firm to ceiling line.
STEP 3:
Position second luminaire in row such that it aligns with joint end (male
end) of first luminaire. Attach customer supplied supports to fixture through
mounting holes located on the top of the housing and to the structure above
as shown in Figure 11. Confirm that fixture is pulled up firm to ceiling line.
Connect the second luminaire to the first luminaire as illustrated in Figure
5. Plug wire harness together and push excess wire into luminaire wiring
chamber, ensure that no wires are pinched. See Figure 11.
STEP 4:
Push luminaires tightly together while making sure the alignment pins
slide into the interior tracks of each luminaire and span the luminaire
joint. Secure joint by tightening supplied keps locknuts on threaded
studs of male joiner bracket. Confirm that luminaires are secured to the
structure above. See Figure 11.
STEP 5:
Continue to install and assemble row following steps 1-4 above. Using
one of the 7/8" dia. holes on the End unit (Left-Hand End of Run)
luminaire, install conduit connector and make electrical connections
per Section 5 “Electrical Connections”.
STEP 6:
Reconnect LED harness. Replace LED trays and lens that was removed
in Step 1 above, ensure that no wires are pinched..
STEP 7:
Hard Ceiling, Overlap Flange Only:
Fill in Sheet Rock mud over tapered extruded flange until smooth. See
Figure 10.
11
Second Luminaire
First Luminaire
Male End
Female End
Wire Harness

8 of 8 LPN00644X0007A0_A
© 2019 Cree Lighting, A company of IDEAL INDUSTRIES. All rights reserved. For informational purposes only. Content
is subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree®and the Cree logo are
registered trademarks of Cree, Inc.
www.creelighting.com
SECTION 5:
ELECTRICAL CONNECTIONS
STEP 1:
For 120/277/347V applications make the following Electrical
Connections:
a. Connect the black luminaire lead to the supply lead.
b. Connect the white luminaire lead to the neutral
supply lead.
c. Connect the green or green/yellow ground lead to
the green supply lead.
For 208/240V applications, make the following Electrical
Connections:
a. Connect Hot 1 supply lead to the black lead.
b. Connect Hot 2 supply lead to the white lead
c. Connect the green or green/yellow ground lead to
the supply ground lead.
STEP 2:
a. If Dimming is an option; connect the violet dimming
positive lead to the supply dimming positive lead. If
dimming is not being used, ensure to cap off the violet
lead.
b. If Dimming is an option; connect the grey dimming
negative lead to the supply dimming negative lead. If
dimming is not being used, ensure to cap off the grey
lead.
GREEN
LINE-BLACK
GROUND-GREEN
NEUTRAL-WHITE
DIM (-) GREY
DIM (+) VIOLET VIOLET
GREY
CORD/ SUPPLY WIRING
LUMINAIRE
NEUTRAL OR HOT 2
LINE OR HOT 1
FCC NOTICE
CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
CAN ICES-005 (A)/NMB-005 (A)