Creek Audio 855C971W(3A) User manual

AA EDCBA
JIHGF
ASSEMBLY INSTRUCTION
855C971W(3A) 3 PC PACK 24~29'' H ADJUSTABLE QUARTER X -BACK CHAIR SET
1
This page lists all the contents included in the
box. Please take the time to identify the
hardware as well as the individual components
to this product. As you unpack and prepare for
assembly, place the contents on a carpeted or
padded area to protect them from damage.
Upper 'U' Tube Leg ExtensionLower 'U' Tube Swivel Ring
Upper Frame
1/4”, 12mm 1/4”, 18mm
Seat Cushion Bolt Bolt
1/4”, 32mm
Bolt
1 pc 1pc 4pcs 1pc 1pc
1 pc 1pc 8pcs 4pcs 4pcs
4 pcs 8pcs 8pcs 1pc 4pcs
ONMLK Screw
3/16”, 28mm
Spring Washer Metal Washer Allen Wrench Foot Pad
(Spare Part)

2
2
1(For 29 inch seat height chair) Insert Leg Extension (C) into the bottom of Upper/Lower
' U ' Tube (A) & (B).
Make sure Leg Extension (C) hole is aligned with the holes of Upper/Lower
' U ' Tube (A) & (B), insert Bolt (H)
into the lower holes, and firmly tighten using Allen Wrench (N).
***Take the Allen Wrench, and turn the bolts until the legs are secure.
DO NOT TIGHTEN COMPLETELY.
Stop when you feel you are adding force to tighten the bolt.
Put Upper
' U ' Tube (A) into the groove of Lower ' U ' Tube (B).
A
A
C
C
C C
C
H
A
N
B
C
H
N

3
4
3Turn the Swivel (D) 45 degrees (as picture shown) for easy assembly. Then put it on Upper/Lower
' U ' tube (A)
& (B), align the holes and firmly tighten with Bolt (I), Spring Washer (L) and Metal Washer (M) using Allen
Wrench (N).
Attach Ring (E) to Upper/Lower
' U ' Tube (A) & (B) and align the holes of Ring (E) with the upper holes of
Upper/Lower
' U ' Tube (A) & (B), then firmly tighten with Bolt (J) using Allen Wrench (N).
NJ
E
E
A
AB

6
5
4
Cleaning & Care
Put the assembled chair up-side-down on Upper Frame (F). Align holes of Swivel (D) with the holes of
Upper Frame (F) and firmly tighten them with Bolt (H), Spring Washer (L) and Metal Washer(M),
using Allen Wrench (N).
Attach Seat Cushion (G) to Upper Frame (F) with Screw (K), firmly tighten with stool (Not provided), then turn
the chair upright.
Stand chair up on an even surface and check that it
is balanced. If there is a slight wobble, apply
downward pressure in the corner where a leg is
uneven. Keeping pressure in that corner, tighten all
bolts. If balanced, apply downward pressure evenly
in the center and tighten all bolts. Do not over-tighten
beyond hole depth.
Treat surface with care. Surface is resistant to scratches but is not scratch resistant. Clean surfaces with a dry or
damp soft cloth. Do not use abrasive cleaners. Hardware may loosen over time. Periodically check that all connections
are tight.
Helpful Tip:
-Instead of applying downward
pressure while reachingunder
to tighten bolts,have someone
sit in the chair while you tighten
the bolts.
Not provided
N
H
L
M
D
F
F
K
K
GG
D
F
F