Creek Company ODC SUPERSPORT XR 1 User manual

ODC SUPERSPORT XR 1
TM
ASSEMBLY INSTRUCTIONS
THIS BOX CONTAINS:
STEEL FRAME
(1) Left Frame Member
(1) Right Frame Member
(1) Seat Support Frame Member with Underseat Lift and Lock Anchor System Attached
(1) Plastic Seat Back
(1) Plastic Seat Bottom
(4) Seat Screws
(2) Seat Assmbly Pins
(2) Foot Bars
(1) Cargo Deck with Motor Mount and Battery plate
(1) Stripping Apron
(8) Snap Pins
(1) Rod Holder
OARS & OARLOCKS
(1) Pair 6-foot 2 piece Oars
(1) Pair Clamp-on Oarlocks
PONTOONS
(1) Left Pontoon
(1) Right Pontoon
(8) Cam Lock Straps
Each Pontoon consists of Nylon Cover with PVC bottom featuring integral Side Storage Pockets,
and Main Bladder with Valve Insert and Valve Plate all preassembled.
PUMP
Complete with a set of Adaptors
OUTDOOR DISCOVERY CRAFTTM

ODC SUPERSPORT XR 1
TM
ASSEMBLY INSTRUCTIONS
OUTDOOR DISCOVERY CRAFTTM
I. PLASTIC SEAT ASSEMBLY
1. Assemble Seat Back to Seat Bottom using Seat Assembly Pins (see gure 1a).
II. ASSEMBLE FRAME
NOTE: Your Frame Assembles using (8) Snap Pins and (4) Seat Screws. Please follow instructions accordingly.
1. Assemble Seat to Seat Support Frame Member using (4) Seat Screws. (See Figure 1a)
2. Assemble Seat Support Frame Member to Left and Right Frame Members using (4) of the Snap Pins. (see gure 1)
3. Assemble Cargo Deck to Left and Right Frame Members using (2) Snap Pins (see gure 1).
4. Assemble Foot Bars to Left and Right Frame Members using (2) Snap Pins (see gures 1).
5. Assemble Rod Holder to Frame where Cargo Deck attaches to Right or Left Frame Members.
III. PONTOON INFLATION
NOTE: Use the large cone Adaptor provided with your Pump. See gure 3b for a detail of the Valve Assembly. Before ination, be
sure to fully seat each Valve Assembly into the Pontoon, screwing tightly by hand. When fully seating Valve Assembly, be
sure that the Valve Plate is in place around Valve Assembly and not restricting the Valve Assembly from a full seal. After
inating, be sure to fully seat the top cap on to each Valve Assembly, screwing tightly by hand. Both are required for an
airtight seal.
1. Inate each Pontoon. The Valve is located inside the Storage Pocket of each Pontoon.(see gure 3).
Inate until rm (do not over inate).
2. Again, be sure top Valve Cap and Valve Assembly are fully seated.
PONTOON DEFLATION: Unscrew entire Valve Assembly from Pontoon.
IV. ATTACH PONTOONS TO FRAME
NOTE: Always inate the Pontoons rst, before attaching to Frame.
1. Position inated Pontoons under the Left and Right Frame Members with ODC SUPERSPORT XR1TM logos oriented to the
outside.The Frame Members t around the Storage Pockets.
2. Attach Pontoons to Frame as illustrated in gures 3 and 3a. Note: Be sure the Straps are pulled tight through the
Cam-lock Buckles. Frame should be positioned forward or aft on the Pontoons to achieve center of gravity for an even
ride when fully loaded on the water.
V. OAR & OARLOCK ASSEMBLY
1. Loosen the wingnut on the Oarlock and slide the Oarlock onto the handle end of the Oar Shaft.
2. Attach blade end of Oar to end of Oar Handle .
3. Place Oarlock Shafts into Frame.
4. With the Oarlocks installed on the Frame, the oars should be equally adjusted left and right allowing at least two
thumbs’ distance between the Oars, to avoid pinching your thumbs when rowing. With the blades perpendicular to
the water, tighten the wingnuts.
VI. ATTACH STRIPPING APRON TO FRAME
1. Snap front two Straps around the Frame underneath the Oarlocks, and snap the back two Straps to the Right and Left Frame
Members just behind the Storage Pockets

b
Valve inside
Storage Pocket
e
Fig. 1
Frame assembly
a. Cargo Deck with Motor Mount
b. Left Frame Member
c. Right Frame Member
d. Seat Support Frame Member
e. Foot Bars
Fig. 1a
Seat Frame assembly
a. Plastic Seat Back
b. Plastic Seat Bottom
c. Seat Support Member
Fig. 3
Pontoon-to-Frame attachment
Frame slips over two Storage Pockets
Rod Holder
Fig. 2
Detail of Snap Pin
installation
All Frame parts attach with
Snap Pins.
Your Frame assembles using
(8) Snap Pins. Please follow
instructions accordingly.
Fig. 3b
Valve insert
detail
Top Valve Cap
Valve Assembly
Valve Plate
Bladder
Fig. 3a
Pontoon-to-frame attachment
Detail of Camlock Strap
Strap
D-Ring
Frame
a
d
c
HIN
HIN
a
b
Seat
Assembly
Pins
c

ODC SUPERSPORT XR 1
TM
OUTDOOR DISCOVERY CRAFT TM
Your ODC Outdoor Discovery CraftTM is designed to give you many years of service.
Please follow ination instructions and warnings carefully.
IF YOU EVER HAVE ANY QUESTIONS OR PROBLEMS WITH YOUR ODC SUPERSPORT XR 1TM PLEASE DO NOT
RETURN IT TO THE DEALER YOU BOUGHT IT FROM. PLEASE CONTACT THE CREEK COMPANY
DIRECTLY AT 970-879-5221. WE ARE OPEN M-F 9AM-5PM MOUNTAIN TIME. OR CONTACT US VIA E-MAIL AT
[e-mail].
HIN is located on square tubing of seat support frame member and on right main frame member (See Figure 1)
Your Creek Company SUPERSPORT XR1TM is guaranteed against defects in material and workmanship for the life of the
product to the original owner. This does not cover damage due to misuse or normal wear and tear.
Warning:
Please read and follow carefully.
1. Always wear a US Coast Guard approved personal otation device when in your ODC SUPERSPORT XR 1TM.
2. Never oat alone.
3. Always check your ODC SUPERSPORT XR 1TM Air Bladders, outer skin and stitching for possible
damage before you use your craft.
4. Never use your craft if you suspect the Air Bladders, outer skin or stitching has been damaged.
5. Never overinate your ODC SUPERSPORT XR 1TM.
6. Never use your ODC SUPERSPORT XR 1TM without the Pontoons fully inated.
7. Your ODC SUPERSPORT XR1TM is not designed for use in salt water.
CARE AND MAINTENANCE:
1. If your Pontoon Bladder is losing air, please check that Valve Assembly and Top Valve Cap are fully seated. Reseat valve assembly
and repeat pontoon ination instructions.
2. Do not store your ODC SUPERSPORT XR 1 TM in direct sunlight.
3. If you are leaving your ODC SUPERSPORT XR 1TM out in the sun for any amount of time, be aware that the heat can increase the
pressure inside the Pontoons to a dangerous level. Let some of the air out of the pontoons if the craft will be out of the water in
the sun for any length of time, or if it is stored in a vehicle, etc.
4. A gain in altitude will increase the pressure in the Pontoons also. If you are taking your inated ODC SUPERSPORT XR 1TM
from a low elevation to a high elevation, be sure to let some of the air out of it.
5. For short term storage, we recommend you let some air out of your pontoons.
6. For long term storage, we recommend you make sure your ODC SUPERSPORT XR 1TM is completely dry,deated and stored
out of the sunlight in a cool dry area.. Do not store your wet ODC SUPERSPORT XR1TM in freezing temperatures as this may
result in Frame and other component damage.
7. Repairing Bladder, use enclosed patch kit. Identify puncture. Fully deate Bladder. Clean and dry area around puncture.
Apply glue to puncture area and patch using applicator straw. Press patch over puncture area.
Allow 24 hours to dry, before inating.
8. Note: Metal parts may rust and are not covered under warranty.
View instructional video at www.creekcompany.com
Accessories are available for your ODC SUPERSPORT XR 1TM .
Ask for them where you bought your ODC SUPERSPORT XR 1™,
or visit the Creek Company Store at www.CreekCompany.com
Creek Company, PO Box 773892, Steamboat Springs, CO 80477
970-879-5221 • fax [phone] • email: [e-mail]
Made in China
Specications and other details subject to change without notice.