Creek Company OUTDOOR DISCOVERY CRAFT ODC SUPERSPORT XR User manual

ODC SUPERSPORT XR
OUTDOOR DISCOVERY CRAFT
ASSEMBLY INSTRUCTIONS
&%!*! & %
%&$
(1) Left Frame Member
(1) ight Frame Member
(1) Seat Support Frame Member with Padded Bottom
(1) Plastic Seat Back
(1) Plastic Seat Bottom
(2) Foot Bars
(1) igid Grid Cargo Deck with Motor Mount
(1) Stripping Apron
(8) Short Snap Pins
!$%!$!%
(1) Pair 6-foot 2 piece Oars
(1) Pair Clamp-on Oarlocks
"! &!! %
(1) Left Pontoon
(1) ight Pontoon
(8) Cam Lock Straps
Each Pontoon consists of 840 Denier Nylon Cover with integral Side Storage Pockets, and
Main Bladder with Valve Insert and Valve Plate all preassembled.
"'"
Complete with a set of Adaptors
"&&
)$$ &+$
TM
TM

ODC SUPERSPORT XR
OUTDOOR DISCOVERY CRAFT
ASSEMBLY INSTRUCTIONS
I. PLASTIC SEAT ASSEMBLY
 Assemble Seat Back to Seat Bottom using Seat Assembly Pins (see figure 1a).
II. ASSEMBLE FRAME
!&Your Frame Assembles using (8) Short Snap Pins. Please follow instructions accordingly.
 Assemble Seat to Seat Support Frame Member using (4) Seat Screws. (See Figure 1a)
 Assemble Seat Support Frame Member to Left and ight Frame Members using (4) of the Short Snap Pins. (see figure 1)
 Assemble Cargo Deck to Left and ight Frame Members using (2) Short Snap Pins (see figure 1).
 Assemble Foot Bars to Left and ight Frame Members using (2) Short Snap Pins (see figures 1).
II. PONTOON INFLATION
!&Use the large cone Adaptor provided with your Pump. See figure 3b for a detail of the Valve Assembly. 019<04816,>498
-0=?<0>91?66C=0,>0,.3(,6@0==07-6C48>9>30"98>998=.<0A482>423>6C-C3,8/)3081?66C=0,>482(,6@0==07-6C
-0=?<0>3,>>30(,6@0"6,>04=48:6,.0,<9?8/(,6@0==07-6C,8/89><0=><4.>482>30(,6@0==07-6C1<97,1?66=0,6
1>0<4816,>482-0=?<0>91?66C=0,>>30>9:.,:98>90,.3(,6@0==07-6C=.<0A482
>423>6C-C3,8/9>3,<0<0;?4<0/19<,8,4<>423>=0,6
 Inflate each Pontoon. The Valve is located inside the Storage Pocket of each Pontoon.(see figure 3).
Inflate until firm (do not over inflate).
 2,48-0=?<0>9:(,6@0,:,8/(,6@0==07-6C,<01?66C=0,>0/
"! &!! &! Unscrew entire Valve Assembly from Pontoon.
III. ATTACH PONTOONS TO FRAME
!&Always inflate the Pontoons first, before attaching to Frame.
 Position inflated Pontoons under the Left and ight Frame Members with ODC SUPE SPO T X logos oriented to the
outside.The Frame Members fit around the Storage Pockets.
 Attach Pontoons to Frame as illustrated in figures 3 and 3a. !& Be sure the Straps are pulled tight through the
Cam-lock Buckles. Frame should be positioned forward or aft on the Pontoons to achieve center of gravity for an even
ride when fully loaded on the water.
IV. OAR & OARLOCK ASSEMBLY
 Loosen the wingnut on the Oarlock and slide the Oarlock onto the handle end of the Oar Shaft.
 Attach blade end of Oar Handle to end of Oar.
 Place Oarlock Shafts into Frame.
 With the Oarlocks installed on the Frame, the oars should be equally adjusted left and right allowing at least two
thumbs’ distance between the Oars, to avoid pinching your thumbs when rowing. With the blades perpendicular to
the water, tighten the wingnuts.
V. ATTACH STRIPPING APRON TO FRAME
 Snap front two Straps around the Frame underneath the Oarlocks, and snap the back two Straps to the Seat Back Frame.
just below the Padded Back and just above the Seat Bottom Frame.
TM
TM

42
<,70,==07-6C
a. Cargo Deck with Motor Mount
b. Left Frame Member
c. ight Frame Member
d. Seat Support Frame Member
e. Foot Bars
42,
%0,><,70,==07-6C
a. Plastic Seat Back
b. Plastic Seat Bottom
c. Seat Support Member
42
0>,4691%8,:"48
48=>,66,>498
All Frame parts attach with Snap
Pins.
Your Frame assembles using
(2) Long Snap Pins and (12) Short
Snap Pins. Please follow
instructions accordingly.
Valve inside
Storage Pockets
Top Valve Cap
Valve assembly
42-
(,6@048=0<>
/0>,46
Valve plate
Bladder
42
"98>998>9<,70,>>,.3708>
Frame slips over two Storage Pockets
-
.
/
0


Pontoon
Strap
Frame
Cam-lock
Buckle
42,
"98>998>91<,70,>>,.3708>
Detail of Camlock Strap
D- ing
%64/0>3<9?23!,<69.5=,8/
199>!,<=,<0,@,46,-60
19<C9?<
!%'"$%"!$& *$
(4=4>
AAA<00597:,8C.97
19</0>,46=9<.,66
B
8.39<<9:,8/
$9/96/0<,<0,@,46,-60
19<C9?<
! %'"$%"!$&*$.
(4=4>
AAA<00597:,8C.97
19</0>,46=9<.,66
B
,
Seat
Back
Seat Bottom
,
Seat
Assembly
Pins
-
.

ODC SUPERSPORT XR
OUTDOOR DISCOVERY CRAFT
),<8482
"60,=0<0,/,8/19669A.,<01?66C
 Always wear a US Coast Guard approved personal flotation device when in your ODC SUPE SPO T X .
 Never float alone.
 Always check your ODC SUPE SPO T X Air Bladders, outer skin and stitching for possible damage before you use your craft.
 Never use your craft if you suspect the Air Bladders, outer skin or stitching has been damaged.
 Never overinflate your ODC SUPE SPO T X .
 Never use your ODC SUPE SPO T X without the Pontoons fully inflated.
 Your ODC SUPE SPO T X is not designed for use in salt water.
CARE AND MAINTENANCE:
 If your Pontoon Bladder is losing air, please check that Valve Assembly and Top Valve Cap are fully seated. eseat valve
assembly and repeat pontoon inflation instructions.
 Do not store your ODC SUPE SPO T X in direct sunlight.
 If you are leaving your ODC SUPE SPO T X out in the sun for any amount of time, be aware that the heat can increase the
pressure inside the Pontoons to a dangerous level. Let some of the air out of the pontoons if the craft will be out of the water in the
sun for any length of time, or if it is stored in a vehicle, etc.
 A gain in altitude will increase the pressure in the Pontoons also. If you are taking your inflated ODC SUPE SPO T X from a
low elevation to a high elevation, be sure to let some of the air out of it.
 For short term storage, we recommend you let some air out of your pontoons.
 For long term storage, we recommend you make sure your ODC SUPE SPO T X is completely dry, deflated and stored out of
the sunlight in a cool dry area.. Do not store your wet ODC SUPE SPO T X in freezing temperatures as this may result in
Frame and other component damage.
. epairing Bladder, use enclosed patch kit. Identify puncture. Fully deflate Bladder. Clean and dry area around puncture. Apply
glue to puncture area and patch using applicator straw. Press patch over puncture area. Allow 24 hours to dry, before inflating.
 Note: Metal parts may rust and are not covered under warranty.
TM
+9?<!!?>/99<4=.9@0<C<,1>4=/0=4280/>924@0C9?7,8CC0,<=91=0<@4.0
"60,=019669A4816,>49848=><?.>498=,8/A,<8482=.,<01?66C
+!'($( +#'%&! %!$"$!%)&+!'$!%'"$%"!$&*$ "%!
!&$&'$ &&!&$+!'!'&&$!"%! &&&$!" +
$&+&!$&)$!" "!' & &!$! &&'%
(& !$!" +!
 %!&! %#'$&' !%&%'""!$&$$
 ! $& $$%'$
Accessories are available for your ODC SUPE SPO T X ™. Ask for them where you bought your ODC SUPE SPO T X ™,
or visit the Creek Company Store at www.CreekCompany.com
&30<00597:,8C>/"!9B%>0,7-9,>%:<482=!
email: [email protected] • Made in China
Specifications and other details subject to change without notice.
All Creek Company products are guaranteed against defects in material and workmanship for the life of the product to
the original owner. This does not cover damage due to misuse or normal wear and tear.
TM