Crestron Electronics CEN-RGBHVHB User manual

Crestron CEN-RGBHVHB
High-Bandwidth RGB Matrix Switcher
Operations Guide

Important Safety Instructions
•Read these instructions.
•Keep these instructions.
•Heed all warnings.
•Follow all instructions.
•Do not use this apparatus near water.
•Clean only with dry cloth.
•
Do not block any ventilation openings. Install in accordance
with the manufacturer's instructions.
•Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
•Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
•Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
•Only use attachments/accessories specified by the
manufacturer.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE. THE APPARATUS SHALL NOT BE EXPOSED
TO DRIPPING OR SPLASHING. OBJECTS FILLED WITH
LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED
ON THE APPARATUS.
WARNING:
TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE
COVER. THERE ARE NO USER SERVICEABLE PARTS
INSIDE. ONLY QUALIFIED SERVICE PERSONNEL
SHOULD PERFORM SERVICE.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product's enclosure t hat may be of sufficient magnitude
to constitute a risk of electric shock to persons.
•Use only with the cart, stand, tripod, bracket or
table specified by the manufacturer or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING:
THIS IS AN APPARATUS WITH CLASS I
CONSTRUCTION. IT SHALL BE CONNECTED TO AN
ELECTRICAL OUTLET WITH AN EARTHING GROUND
TERMINAL.
IMPORTANT:
This device can be used with Class 2 output wiring.
•Unplug this apparatus during lightning storms or when
unused for long periods of time.
•Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has bee
n spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
•Disconnect power prior to connecting or disconnecting
equipment.
•Do not install in direct sunlight.
•The
apparatus must be installed in a way that the power cord
can be removed either from the wall outlet or from the
device itself in order to disconnect the mains power.
•Prevent foreign objects from entering the device.

The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, Cresnet, Crestron e-Control, Crestron Studio, Crestron Toolbox, e-Control, Fusion RV, and SystemBuilder are either
trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks,
and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any
proprietary interest in the marks and names of others. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not
responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2013 Crestron Electronics, Inc.
Regulatory Compliance
This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
As of the date of manufacture, the CEN-RGBHVHB has been tested and found to comply with specifications
for CE marking and standards per EMC and Radiocommunications Compliance Labelling.
Federal Communications Commission (FCC) Compliance Statement
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and receiver
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
•Consult the dealer or an experienced radio/TV technician for help
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)


Crestron CEN-RGBHVHB High-Bandwidth RGB Matrix Switcher
Operations Guide – DOC. 7157C Contents •i
Contents
High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB 1
Introduction ............................................................................................................................... 1
Features and Functions ................................................................................................1
Specifications ..............................................................................................................3
Physical Description....................................................................................................6
Setup ........................................................................................................................................ 13
Network Wiring......................................................................................................... 13
Identity Code ............................................................................................................. 13
Installation ................................................................................................................. 14
Hardware Hookup ..................................................................................................... 16
Uploading and Upgrading........................................................................................................ 18
Establishing Communication..................................................................................... 18
Programs and Firmware ............................................................................................ 19
Program Checks ........................................................................................................ 20
Operation ................................................................................................................................. 21
Menu Structure .......................................................................................................... 21
Setup and Informational Screens............................................................................... 21
Routing Signals ......................................................................................................... 41
Sync Mode................................................................................................................. 42
Paging Mode.............................................................................................................. 42
Problem Solving ...................................................................................................................... 43
Troubleshooting......................................................................................................... 43
Check Network Wiring.............................................................................................. 43
Reference Documents................................................................................................ 44
Further Inquiries ........................................................................................................ 44
Future Updates .......................................................................................................... 44
Return and Warranty Policies .................................................................................................. 45
Merchandise Returns / Repair Service ...................................................................... 45
Crestron Limited Warranty........................................................................................ 45


Crestron CEN-RGBHVHB High-Bandwidth RGB Matrix Switcher
Operations Guide – DOC. 7157C High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB •1
•Ultra high bandwidth matrix switcher
8 x 4 in CEN-RGBHVHB8X4
8 x 8 in CEN-RGBHVHB8X8
12 x 4 in CEN-RGBHVHB12X4
12 x 8 in CEN-RGBHVHB12X8
•800 MHz video bandwidth (-3 dB)
•Incredibly wide response and low crosstalk
•Stereo audio signal routing with breakaway
•Audio DSP with volume, tone, and graphic EQ
•Paging mode with automatic ducking
•Professional balanced audio inputs and outputs
•Audio input level compensation
•Video input sync detection
•Video-follow-sync switching technology
•Adjustable video and audio blanking
•Selectable input sync impedance on all inputs
•LCD front panel for easy setup and standalone operation
•Crestron system integration via Cresnet®or Ethernet
•Very low power consumption and a quiet fanless design
•3-space rack mountable
High-Bandwidth RGB Matrix
Switcher: CEN-RGBHVHB
Introduction
Crestron®High-Bandwidth RGB Matrix Switchers deliver extreme performance for
the most demanding presentation environments. With class-leading 800 MHz
bandwidth, low crosstalk, and super wide response, the CEN-RGBHVHB8X4,
CEN-RGBHVHB8X8, CEN-RGBHVHB12X4, and CEN-RGBHVHB12X8
(hereinafter collectively referred to as CEN-RGBHGVHB) easily surpass any
requirement for high-performance, high-resolution analog video and computer signal
routing. Factor in their enhanced audio DSP, very low power consumption, and
native Crestron system integration and any of these is a solid winner for all analog
video and audio signal routing applications.
Features and Functions

High-Bandwidth RGB Matrix Switcher Crestron CEN-RGBHVHB
2•High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB Operations Guide – DOC. 7157C
800 MHz Bandwidth Matrix Router
The CEN-RGBHVHB is capable of routing up to eight (CEN-RGBHVHB8X4,
CEN-RGBHVHB8X8) or 12 (CEN-RGBHVHB12X4, CEN-RGBHVHB12X8)
computer or video sources to up to four (CEN-RGBHVHB8X4,
CEN-RGBHVHB12X4) or eight (CEN-RGBHVHB8X8, CEN-RGBHVHB12X8)
display devices. Its five matrix levels accommodate any combination of analog
RGBHV, HD/component, S-video and composite signals. Ultra high bandwidth and
wide response ensure optimum performance for every signal as part of any AV
system. Sync impedances for each input are selectable from the front panel or
software to accommodate both short and long cable runs.
Glitch-free Switching
Video-follow-sync switching ensures a smooth transition when selecting between
non-synchronous sources. Adjustable blanking allows each display device time to
lock to the new sync signal before displaying the video image whenever a new
source is selected.
Sync Detection
Sync detection on each H and V input measures the sync rates of every RGBHV
source and allows their values to be viewed on the front panel display, on the control
system touch screen, or through Crestron’s Fusion RV®software.*
Audio Routing & DSP
Professional audio signal processing affords enhanced, high-performance audio
routing and control, potentially eliminating the need for additional audio
components. Each stereo output features real time controllable volume, bass, treble,
and mute controls, plus 5-band EQ with customizable presets. Programmable input
level compensation helps ensure compatibility with a wide range of pro and semi-pro
sources. Automatic blanking achieves a pop-free transition when switching between
sources, while audio breakaway capability allows the routing of audio signals to
follow video or be switched independently. The entire audio signal path has been
designed from the ground up to deliver ultra quiet, distortion-free sound quality —
whether feeding sensitive amplifiers, assistive listening devices, or recording and
broadcast equipment.
Paging Mode
Built-in page override functionality simplifies system design, employing automatic
mixing and ducking for a single audio paging source. When set to Paging mode, an
audio signal at the last input channel is automatically distributed to every output
while the signals currently routed to each output are attenuated or “ducked” to allow
the paging signal to be heard. The sensitivity and ducking amount are fully
adjustable for smooth paging behavior and a natural transition back to the previous
audio state.
Full-featured Front Panel
The CEN-RGBHVHB is fully operable out-of-the-box for use as a standalone
switcher. Featuring an informative LCD display, quick-adjust knob, and quick access
buttons, the front panel supports essential switcher operation without requiring a
computer or control system. Advanced setup is available through Crestron
Toolbox™ software. All signal routing, input impedances, and audio settings are
stored in non-volatile memory onboard the switcher.
* Sync detection reports discrete H and V signals only.

Crestron CEN-RGBHVHB High-Bandwidth RGB Matrix Switcher
Operations Guide – DOC. 7157C High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB •3
Customizable label strips are provided on the front panel for clear designation of its
inputs and outputs using Crestron Engraver software or standard 3/8” tape labels.
Names may also be entered through software to appear on the LCD display during
operation. For security, front panel controls can be password protected or locked out.
Crestron System Integration
Via Cresnet or high speed Ethernet, Crestron switchers offer the ultimate in control
system integration. Every function is accessible for custom programming through
Crestron Studio™, SIMPL Windows or SystemBuilder™ software without
deciphering cryptic protocols. Up to 10 routing presets can be saved onboard for
instant recall. Integration with a Crestron control system also provides the gateway to
Fusion RV and e-Control®remote control and management solutions.
Specifications
Specifications for the CEN-RGBHVHB are listed in the following table.
CEN-RGBHVHB Specifications
SPECIFICATION DETAILS
Video/RGB
Switcher CEN-RGBHVHB8X4: 8 x 4 (x 5)
CEN-RGBHVHB8X8: 8 x 8 (x 5)
CEN-RGBHVHB12X4: 12 x 4 (x 5)
CEN-RGBHVHB12X8: 12 x 8 (x 5)
matrix video-follow-sync switching, adjustable
blanking, sync detection, sync regeneration,
front panel selectable sync input termination
Signal Types RGB and composite, S-video or component
video (does not transcode)
Video/HD Formats
NTSC or PAL, HD up to 1080i/1080p
RGB Formats RGBHV, RGBS
1
, RGsB
1
or YUV
1
Horizontal Frequency: 10 kHz to 200 kHz
Vertical Frequency: 20 Hz to 200 Hz
Gain
0 dB (75
Ω
terminated)
Bandwidth 800 MHz (-3 dB)
Blanking Time Adjustable 0 to 10 seconds, 0.5 second steps
Sync Rise/Fall Time: 2 ns maximum
Audio
Switcher Stereo matrix switching
CEN-RGBHVHB8X4: 8 x 4
CEN-RGBHVHB8X8: 8 x 8
CEN-RGBHVHB12X4: 12 x 4
CEN-RGBHVHB12X8: 12 x 8
Adjustable blanking; audio breakaway; input
gain compensation; 4-channel or 8-channel2
stereo DSP with 5-band graphic EQ, volume,
bass, treble, and mute control; Paging mode
(signal at last input momentarily mixes with or
overrides the current selected input at every
output with adjustable sensitivity and ducking
behavior)
(Continued on following page)

High-Bandwidth RGB Matrix Switcher Crestron CEN-RGBHVHB
4•High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB Operations Guide – DOC. 7157C
CEN-RGBHVHB Specifications (Continued)
SPECIFICATION DETAILS
Audio (Continued)
Signal Types Balanced and unbalanced stereo analog line
level
•Typical of Stereo Inputs:
Analog to Digital Conversion 24-bit 48 kHz
Input Compensation ±10 dB per input
•Last input only,
Paging Mode:
Mix Input Level 0 to 100%
Sensing Threshold -80 to 0 dB
Sensing Attack Time 1 to 250 ms
Sensing Hold Time: 1 to 2000 ms
Ducking Depth 0 to 80 dB attenuation
Ducking Release Time 1 to 1000 ms per dB of recovery
•Typical of Stereo Outputs:
Digital-to-Analog Conversion 24-bit 48 kHz
Frequency Response 20 Hz to 20 kHz ±0.5 dB
THD + Noise 0.005%
S/N Ratio >104 dB @ full output, A-weighted
Stereo Separation >104 dB
Output Channel Separation >100 dB
Blanking Time Adjustable 0 to 10 seconds, 0.5 second steps
Output Volume Level Control -80.0 to +20.0 dB, adjustable from 0% to
100% plus mute
Bass Control ±15 dB
Treble Control ±15 dB
EQ Mode 5-band graphic EQ
GEQ Center Frequencies 63, 200, 550, 2 kHz, 12 kHz
GEQ Gain ±12 dB per band
Communications
Ethernet For control and console, 10/100 Mbps,
auto-switching, auto-negotiating,
auto-discovery, full/half duplex, TCP/IP,
UDP/IP CIP, DHCP
Cresnet For control and console, Cresnet slave
USB USB client for computer console
Power Requirements
Main Power 1 amp maximum @ 100-240 volts ac,
50/60 Hz
Power Consumption 30 watts maximum
Cresnet Power Usage None
Default Net ID 33
(Continued on following page)

Crestron CEN-RGBHVHB High-Bandwidth RGB Matrix Switcher
Operations Guide – DOC. 7157C High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB •5
CEN-RGBHVHB Specifications (Continued)
SPECIFICATION DETAILS
Environmental
Temperature 32º to 104º F (0º to 40º C)
Humidity 10% to 90% RH (non-condensing)
Heat Dissipation 102 Btu/h maximum
Enclosure
Chassis Metal, matte black finish, convection cooled,
vented sides
Faceplate Metal, matte black finish, with polycarbonate
label overlay
Mounting Freestanding or 3U 19-inch rack mountable
(adhesive feet and rack ears included)
Dimensions
Height 5.20 in (132 mm) without feet
Width 17.03 in (433 mm);
19.00 in (483 mm) with ears
Depth 13.13 in (334 mm)
Weight 14.5 lb (6.6 kg)
1. Sync detection reports discrete H and V signals only.
2. 4-channel on CEN-RGBHVHB8X4 and CEN-RGBHVHB12X4; 8-channel on CEN-RGBHVHB8X8
and CEN-RGBHVHB12X8.

High-Bandwidth RGB Matrix Switcher Crestron CEN-RGBHVHB
6•High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB Operations Guide – DOC. 7157C
Physical Description
This section provides information on the connections, controls and indicators
available on the CEN-RGBHVHB.
CEN-RGBHVHB8X4 Front View
CEN-RGBHVHB8X4 Rear View

Crestron CEN-RGBHVHB High-Bandwidth RGB Matrix Switcher
Operations Guide – DOC. 7157C High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB •7
CEN-RGBHVHB8X8 Front View
CEN-RGBHVHB8X8 Rear View
CEN-RGBHVHB12X4 Front View

High-Bandwidth RGB Matrix Switcher Crestron CEN-RGBHVHB
8•High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB Operations Guide – DOC. 7157C
CEN-RGBHVHB12X4 Rear View
CEN-RGBHVHB12X8 Front View
CEN-RGBHVHB12X8 Rear View

Crestron CEN-RGBHVHB High-Bandwidth RGB Matrix Switcher
Operations Guide – DOC. 7157C High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB 9
CEN-RGBHVHB8X4, CEN-RGBHVHB8X8, CEN-RGBHVHB12X4, CEN-RGBHVHB12X8 Overall Dimensions
(CEN-RGBHVHB12X8 Shown)

High-Bandwidth RGB Matrix Switcher Crestron CEN-RGBHVHB
10 •High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB Operations Guide – DOC. 7157C
Connectors, Controls & Indicators
# CONNECTORS1,
CONTROLS &
INDICATORS
DESCRIPTION
1 LCD Display Green LCD alphanumeric, adjustable backlight,
2 lines x 20 characters per line;
Displays inputs/outputs by name, scan rates,
audio settings, IP configuration and setup
menus
2 Soft Keys (4) push buttons for execution of LCD driven
functions
3 MENU (1) push button, steps menu back one level
4 ENTER (1) push button, executes highlighted menu or
value
5 A (1) push button & red LED, selects audio
routing view
6 V (1) push button & red LED, selects video
routing view
7 SYNC (1) push button & red LED, displays input sync
rate
8 IN (8 or 12)
2
push buttons & red LEDs, select
input to be routed
9 COMPUTER
USB
Pin 2 Pin 1
Pin 3 Pin 4
(1) USB Type B female;
USB computer console port
(6 foot cable included)
PIN DESCRIPTION
1 +5 Vdc
2
Data -
3
Data +
4
Ground
10 HW-R (1) recessed miniature push button for
hardware reset, reboots the switcher
11 CLEAR (1) push button & red LED, clears all matrix
routing
12 VIEW (1) push button & red LED, toggles View mode
on/off
13 TAKE (1) push button & red LED, executes routing
14 Quick-Adjust Knob (1) continuous turn rotary encoder, adjusts
menu parameters
15 OUT (4 or 8)
3
push buttons & red LEDs, select
output destination(s)
(Continued on following page)

Crestron CEN-RGBHVHB High-Bandwidth RGB Matrix Switcher
Operations Guide – DOC. 7157C High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB •11
Connectors, Controls & Indicators (Continued)
# CONNECTORS1,
CONTROLS &
INDICATORS
DESCRIPTION
16 (VIDEO) IN
(8 or 12)
2
sets of (5) BNC female;
RGB, component, S-video, or composite video
inputs;
Formats: RGBHV, RGBS, RGsB, YUV, YPbPr,
Y/C, NTSC, PAL;
RGB input level: 1 Vp-p with ±0.5 Vdc offset
maximum;
RGB input impedance: 75 Ωnominal;
Sync input types: RGBHV, RGBS4, RGsB4,
YPbPr4;
Sync input level: 3 to 5 Vp-p;
Sync input impedance: 75 or 510 Ω,
independently selectable for H and V per input;
Sync detection: Reports discrete H and V
signal presence and sync rates per input
17 (VIDEO) OUT
(4 or 8)
3
sets of (5) BNC female;
RGB, Component, S-video, or composite video
outputs;
Formats: Same as selected input;
RGB output level: Same as selected input;
RGB output impedance: 75 Ωnominal;
Sync output type: Same as selected input;
Sync output level: 5 Vp-p
18 LAN
Green
LED
Amber
LED Pin 1
Pin 8
(1) 8-wire RJ-45 female (8P8C modular jack)
with two LED indicators;
10BASE-T/100BASE-TX Ethernet port;
Green LED indicates Ethernet link status;
Amber LED indicates Ethernet activity;
PIN
SIGNAL
PIN
SIGNAL
1
TX +
5
N/C
2
TX -
6
RC -
3
RC+
7
N/C
4
N/C
8
N/C
19 G
(1) 6-32 screw, chassis ground lug
20 NET
G
Z
Y
24
(1) 4-pin 3.5 mm detachable terminal block;
Cresnet slave port, connects to Cresnet control
network;
Does not draw power from the network
(Continued on following page)

High-Bandwidth RGB Matrix Switcher Crestron CEN-RGBHVHB
12 •High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB Operations Guide – DOC. 7157C
Connectors, Controls & Indicators (Continued)
# CONNECTORS1,
CONTROLS &
INDICATORS
DESCRIPTION
21 100-240V
~50/60Hz
1.0A Max
(1) IEC C14 male chassis plug, main power
input;
Mates with removable power cord (included)
22 (AUDIO) IN
L R
+ - G + -
(8 or 12)25-pin 3.5 mm detachable terminal
blocks;
Balanced/unbalanced stereo line level inputs;
Maximum input level: 4 Vrms balanced,
2 Vrms unbalanced;
Input impedance: 24 kΩbalanced,
12 kΩunbalanced
NOTE: Last input (8 or 12) may be configured
for Paging mode
23 AUDIO OUT (L/R)
+ - G + -
L R
(4 or 8)
3
5-pin 3.5 mm detachable terminal
blocks;
Balanced/unbalanced stereo line level outputs;
Maximum output level: 4 Vrms balanced,
2 Vrms unbalanced;
Output impedance: 200 Ωbalanced,
100 Ωunbalanced.
1. Interface connectors for the NET port and the (Audio) INPUT and OUTPUT ports are provided with
the unit.
2. 1 – 8 on CEN-RGBHVHB8X4 and CEN-RGBHVHB8X8; 1 – 12 on CEN-RGBHVHB12X4 and
CEN-RGBHVHB12X8.
3. 1 – 4 on CEN-RGBHVHB8X4 and CEN-RGBHVHB12X4; 1 – 8 on CEN-RGBHVHB8X8 and
CEN-RGBHVHB12X8.
4. Sync detection reports discrete H and V signals only.

Crestron CEN-RGBHVHB High-Bandwidth RGB Matrix Switcher
Operations Guide – DOC. 7157C High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB •13
Setup
Network Wiring
When wiring the Cresnet network, consider the following:
•Use Crestron Certified Wire.
•Use Crestron power supplies for Crestron equipment.
•Provide sufficient power to the system.
CAUTION: Insufficient power can lead to unpredictable results or damage
to the equipment. Use the Crestron Power Calculator to help calculate how
much power is needed for the system (www.crestron.com/calculators).
For Cresnet networks with 20 or more devices, use a Cresnet Hub/Repeater
(CNXHUB) to maintain signal quality.
For more details, refer to “Check Network Wiring” which starts on page 43.
The CEN-RGBHVHB can also use high-speed Ethernet for communications
between the device and a control system.
For general information on connecting Ethernet devices in a Crestron system, refer to
the latest version of the Crestron e-ControlReference Guide (Doc. 6052), which is
available from the Crestron Web site (www.crestron.com/manuals).
Identity Code
NOTE: The latest software can be downloaded from the Crestron Web site
(www.crestron.com/software).
Net ID The Net ID of the CEN-RGBHVHB has been factory set to 33. The Net IDs of
multiple CEN-RGBHVHB devices in the same system must be unique. Net IDs are
changed from a personal computer (PC) via Crestron Toolbox (refer to “Establishing
Communication” which starts on page 18).
When setting the Net ID, consider the following:
•The Net ID of each unit must match an ID code specified in the Crestron
Studio or SIMPL Windows program.
•Each network device must have a unique Net ID.
For more details, refer to the Crestron Toolbox help file.
IP ID The IP ID is set within the CEN-RGBHVHB’s IP table using Crestron Toolbox. For
information on setting an IP table, refer to the Crestron Toolbox help file. The IP IDs
of multiple CEN-RGBHVHB devices in the same system must be unique.
When setting the IP ID, consider the following:
•The IP ID of each unit must match an IP ID specified in the Crestron Studio
or SIMPL Windows program.
•Each device using IP to communicate with a control system must have a
unique IP ID.

High-Bandwidth RGB Matrix Switcher Crestron CEN-RGBHVHB
14 •High-Bandwidth RGB Matrix Switcher: CEN-RGBHVHB Operations Guide – DOC. 7157C
Installation
Ventilation The CEN-RGBHVHB should be used in a well-ventilated area. The venting holes
should not be obstructed under any circumstances.
To prevent overheating, do not operate this product in an area that exceeds the
environmental temperature range listed in the table of specifications. Consider using
forced air ventilation and/or incrementing the spacing between units to reduce
overheating. Contact with thermal insulating materials should be avoided on all sides
of the unit.
Rack Mounting The CEN-RGBHVHB can be mounted in a rack or stacked with other equipment.
Two “ears” and an appropriate number of longer screws are provided with the
CEN-RGBHVHB so that the unit can be rack mounted. These ears must be installed
prior to mounting. Complete the following procedure to attach the ears to the unit.
The only tool required is a #1 or #2 Phillips screwdriver.
WARNING: To prevent bodily injury when mounting or servicing this unit in a
rack, observe the following guidelines:
•When mounting this unit in a partially filled rack, load the rack from the
bottom to the top with the heaviest component at the bottom of the rack.
•If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
NOTE: Observe the following guidelines when installing equipment in a rack:
•Elevated Operating Ambient Temperature - If installed in a closed or
multi-unit rack assembly, the operating ambient temperature of the rack
environment may be greater than room ambient temperature. Therefore,
consideration should be given to installing the equipment in an environment
compatible with the maximum ambient temperature (Tma) specified by the
manufacturer.
•Reduced Air Flow - Installation of the equipment in a rack should be such
that the amount of airflow required for safe operation of the equipment is
not compromised.
•Mechanical Loading - Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
•Circuit Overloading - Consideration should be given to the connection of
the equipment to the supply circuit and the effect that overloading of the
circuits might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used
when addressing this concern.
•Reliable Earthing - Reliable earthing of rack-mounted equipment should be
maintained. Particular attention should be given to supply connections other
than direct connections to the branch circuit (e.g., use of power strips)
NOTE: If rack mounting is not required, rubber feet are provided for tabletop
mounting or stacking. Apply the feet near the corner edges on the underside of the
unit.
This manual suits for next models
4
Table of contents
Other Crestron Electronics Matrix Switcher manuals