Crestron IV-CAMA3 Series Quick setup guide

SYSTEMS
Mira Connect Integration Guide for
Crestron IV‑CAMA3 Series Camera
Integrating a Crestron IV‑CAMA3 Series Camera with Mira Connect™
Crestron IV‑CAMA3 Series Cameras can be controlled by Mira Connect™, Aveo Systems’ smart control appliance. Mira Connect
uses Sony’s VISCA (Video System Control Architecture) camera protocol to control pan, tilt, zoom, and presets.
Figure 1: Mira Connect controls thousands of products, including Crestron IV‑CAMA3 Series Cameras.
Mira Connect supports camera pan, tilt, zoom, and tracking control, and saving and recalling camera presets.
Integration Steps
Step 1. Add the desired room to Mira Portal
To get started, create an organization, site, and room in Mira Portal if you don’t already have a room. Follow the tutorial for
creating a room aer creating a Mira Portal account. There is no cost to creating a Mira Portal account.
Next, pair a Mira Connect to the room or use the Preview Mira Connect in a web browser feature.
Aveo Systems, Inc. • 4455 Lower Roswell Road #681593 • Marietta, GA 30068
Phone: [phone] • Email: [e-mail] • aveosystems.com 1Copyright © Aveo Systems, Inc. All rights reserved.

SYSTEMS
Mira Connect Integration Guide for
Crestron IV‑CAMA3 Series Camera
Organizations
ALL ROOMS IN CALL ALERTS
100
Board Room
1 room
Sites Rooms
ADD ADD ADD
1 Site
!
Mira Portal JOEHELP
?
Equipment
Shades
Video Source Menus
Recent Events
Recent Calls
Settings
Permissions
Licenses
API
REMOTE CONTROL
192.168.80.88 (Wired, MAC: 00:04:3b:04:e5:d7)
Android 6.0.1
62%
Mira Connect 1.34.1.3
{ }
Mira Connect
Your Site
Your Site
Your Organization
Your Organization Board Room
PAIR
Mira Connect
No controllers are paired.
Mira Connect
Preview Mira Connect in a web browser
Figure 2: Create an organization, site, and room in Mira Portal and then pair the Mira Connect to the room.
Step 2. Pair Mira Connect to the room
If you have a Mira Connect appliance, connect it to the network and power it up. Mira Connect appliances can use a PoE
network connection. Mira Connect requires WAN access to pair with the room in Mira Portal.
The Preview Mira Connect in a web browser feature opens a new browser tab and creates an interactive demo of the user
interface before you have a Mira Connect or any equipment. The preview feature uses Mira Connect’s built‑in equipment
emulators to create an interactive user experience before any equipment is purchased.
To pair a Mira Connect control system to your room:
• For Mira Connect appliances, select your language, network (wired or wireless), and then Mira Connect will show a
pairing code. Enter the pairing code into Mira Portal to associate the Mira Connect with the room in Mira Portal.
• If you are using Mira Connect soware, follow the instructions in the Mira Connect Soware Quick Install Guide to install
the Mira Connect soware and get a pairing code.
The following figures show the pairing steps when using Mira Connect appliances.
Aveo Systems, Inc. • 4455 Lower Roswell Road #681593 • Marietta, GA 30068
Phone: [phone] • Email: [e-mail] • aveosystems.com 2Copyright © Aveo Systems, Inc. All rights reserved.

SYSTEMS
Mira Connect Integration Guide for
Crestron IV‑CAMA3 Series Camera
English (US)
CONTINUE
Select Application Language Wired
Select Network Connection
WIRED
WIRELESS
Wired
Connected
Pair Mira Connect to Room Wired
Sign in to Mira Portal on your computer, then:
Select
the room
Pair
Mira Connect
Enter
the pairing code
shown below
Expires in 60 minutes
1 3 1 4 1 1
Figure 3: Select the language, select the network connection, and receive a pairing code.
Step 3. Add the Crestron IV‑CAMA3 Series Camera
To integrate a Crestron IV‑CAMA3 Series Camera with Mira Connect, add a ‘Crestron IV‑CAMA3 Series Camera’ to the room in
Mira Portal (https://mira.aveosystems.com).
Aveo Systems, Inc. • 4455 Lower Roswell Road #681593 • Marietta, GA 30068
Phone: [phone] • Email: [e-mail] • aveosystems.com 3Copyright © Aveo Systems, Inc. All rights reserved.

SYSTEMS
Mira Connect Integration Guide for
Crestron IV‑CAMA3 Series Camera
Add Equipment
Cameras
Contact Closure & Serial/Logic/IR Output
Control By Web X-4xx Series
Global Caché GC-100, iTach, Flex, Global Connect
Crestron Automate VX
Crestron IV-CAMA3 Series
Panasonic AW-UE Series
Universal VISCA Camera
Vaddio RoboSHOT
Aver CAM550
Figure 4: Click Add and select the Crestron IV‑CAMA3 Series Camera from the equipment list.
Enter the IP address of the camera and the port number.
Aveo Systems, Inc. • 4455 Lower Roswell Road #681593 • Marietta, GA 30068
Phone: [phone] • Email: [e-mail] • aveosystems.com 4Copyright © Aveo Systems, Inc. All rights reserved.

SYSTEMS
Mira Connect Integration Guide for
Crestron IV‑CAMA3 Series Camera
Questions about Crestron IV-CAMA3 Series?
See the step by step integration guide.
Update Equipment
CONNECTION CAMERA CONFIGURATION CAMERA PRESETS
Equipment Type*
Simulate equipment
Crestron IV-CAMA3 Series
OPTIONS
UPDATE EQUIPMENTCANCEL
Didn’t find your equipment? Request it!
i
RESET TO DEFAULT
CONNECTION
192.168.100.192
5500
IP Address or Hostname *
Port Number *
ADD EQUIPMENT
Figure 5: Enter the IP address and port number to add the Crestron IV‑CAMA3 Series Camera. The default port number is
5500 for a direct network connection or port 4999 when using a Global Caché IP2SL.
If you don’t have an actual Crestron IV‑CAMA3 Series Camera while configuring Mira Connect, you can choose to simulate the
Crestron IV‑CAMA3 Series Camera by checking ‘Simulate equipment’.
Step 4. Enter the Camera Name
Next, navigate to the Camera Configuration tab and enter the camera’s ID (typically 1) and enter a name for the camera and
press ‘add equipment’.
Aveo Systems, Inc. • 4455 Lower Roswell Road #681593 • Marietta, GA 30068
Phone: [phone] • Email: [e-mail] • aveosystems.com 5Copyright © Aveo Systems, Inc. All rights reserved.

SYSTEMS
Mira Connect Integration Guide for
Crestron IV‑CAMA3 Series Camera
Questions about Crestron IV-CAMA3 Series?
See the step by step integration guide.
Update Equipment
CONNECTION CAMERA CONFIGURATION CAMERA PRESETS
Equipment Type*
Simulate equipment
Crestron IV-CAMA3 Series
OPTIONS
UPDATE EQUIPMENTCANCEL
Didn’t find your equipment? Request it!
i
Camera ID * Camera Name * Pan Speed * Tilt Speed * Zoom Speed *
Pan Speed (Slow) * Tilt Speed (Slow) * Zoom Speed (Slow) *
Invert Pan Controls
1 Presenter Camera 8 8 3
3 3 1
REMOVE
Enable deep sleep support ?
Figure 6: Enter a camera name on the Camera Controls tab.
Step 5. Connect to the Camera
Once the cameras have been added, Mira Connect will connect to the device(s) and show the status of the connection. Mira
Portal will show the equipment status as a green circle with a check mark if the equipment was detected at the specified IP
address and network port and is controllable by Mira Connect.
Crestron IV-CAMA3 Series
Equipment ADD
Firmware: 00 01 04 02 01 15 02
192.168.100.192
Crestron IV-CAMA3 Series
Equipment ADD
Connection failed
!
192.168.100.126
Figure 7: Successful connection to the Crestron IV‑CAMA3 Series Camera (le) and failed connection (right).
Aveo Systems, Inc. • 4455 Lower Roswell Road #681593 • Marietta, GA 30068
Phone: [phone] • Email: [e-mail] • aveosystems.com 6Copyright © Aveo Systems, Inc. All rights reserved.

SYSTEMS
Mira Connect Integration Guide for
Crestron IV‑CAMA3 Series Camera
If Mira Connect cannot connect to the camera, a red warning icon will appear on the equipment list.
• If Mira Connect cannot connect to the camera over the network, confirm the IP address of the camera and that Mira
Connect is on the same network as the camera.
• If Mira Connect cannot connect to the camera over RS‑232, first check the RS‑232 baud rate used by the Global Caché
IP2SL (most VISCA cameras operate at 9600 bps while the Global Caché IP2SL defaults to 19,200), and then edit the
camera settings have enabled VISCA over RS‑232 and confirm the IP address, port number (4999 for a Global Caché
IP2SL.
Step 6. Add Camera Presets
To add Camera Presets, press the Camera icon on Mira Connect and select a camera from the camera pull‑down box on Mira
Connect.
Next, manually position the camera using Mira Connect (or use the remote control capabilities from Mira Portal) to the desired
location and zoom level.
Next, edit the equipment in Mira Portal and navigate to the Camera Presets tab. Select the desired camera from the pull down
list, and click ADD PRESET. Select an icon, and enter a preset name and optional description.
Once the camera is in the desired location, press SAVE PRESET to save that camera position. Repeat the process for saving
multiple camera presets. When finished saving presets, click Update Equipment to store the preset information and update
the user interface on Mira Connect.
Presets will appear in Mira Connect as shown on the right side of the following figure.
Aveo Systems, Inc. • 4455 Lower Roswell Road #681593 • Marietta, GA 30068
Phone: [phone] • Email: [e-mail] • aveosystems.com 7Copyright © Aveo Systems, Inc. All rights reserved.

SYSTEMS
Mira Connect Integration Guide for
Crestron IV‑CAMA3 Series Camera
Questions about Crestron IV-CAMA3 Series?
See the step by step integration guide.
Update Equipment
CONNECTION CAMERA CONFIGURATION CAMERA PRESETS
Equipment Type*
Simulate equipment
Crestron IV-CAMA3 Series
OPTIONS
UPDATE EQUIPMENTCANCEL
Didn’t find your equipment? Request it!
i
CAMERA PRESETS
Camera
These preset items will appear on Mira Connect.
Icon Label
WIDE VIEW
WIDE VIEW
ADD PRESET
SAVE POSITIONREMOVE
View of the Room
View of the Room Front of Room
Front of Room
Camera Presets Preview
Camera presets:
After adding a preset, save the current camera position
to that preset with the “Save Position” button.
Descrip on (Op onal)
Label
PRESENTER
PRESENTER
SAVE POSITIONREMOVE
Front of Room
Descrip on (Op onal)
Smaller Mee ng One on One
TABLE END CLOSE UP VIEW
Figure 8: Camera presets are added through Mira Portal.
Camera Positioning Speed Control
Mira Portal supports setting camera movement speeds for pan, tilt, and zoom both when the movement button is tapped and
when it is held. To configure these settings, navigate to the Camera Configuration tab in Mira Portal and increase or decrease
the motion speed as shown in the following figure. Pan speed can be adjusted from 1 to 24 (fastest), tilt speed from 1 to 20
(fastest), and zoom speed from 1 to 7 (fastest).
The first row of speed controls aect when the pan, tilt, or zoom button is pressed and held. Default values are Pan Speed: 8,
Tilt Speed: 8, and Zoom Speed: 3.
The second row of speed controls aect when the pan, tilt, or zoom button is tapped. Default speed values are Pan Speed
(Slow): 3, Tilt Speed (Slow): 3, and Zoom Speed (Slow): 1.
To increase the speed of camera movement, increase the speed value. To decrease the speed of movement ‑ mostly used
when tapping the button once moves the camera too much ‑ lower the speed number.
Aveo Systems, Inc. • 4455 Lower Roswell Road #681593 • Marietta, GA 30068
Phone: [phone] • Email: [e-mail] • aveosystems.com 8Copyright © Aveo Systems, Inc. All rights reserved.

SYSTEMS
Mira Connect Integration Guide for
Crestron IV‑CAMA3 Series Camera
Questions about Crestron IV-CAMA3 Series?
See the step by step integration guide.
Update Equipment
CONNECTION CAMERA CONFIGURATION CAMERA PRESETS
Equipment Type*
Simulate equipment
Crestron IV-CAMA3 Series
OPTIONS
UPDATE EQUIPMENTCANCEL
Didn’t find your equipment? Request it!
i
Camera ID * Camera Name * Pan Speed * Tilt Speed * Zoom Speed *
Pan Speed (Slow) * Tilt Speed (Slow) * Zoom Speed (Slow) *
Invert Pan Controls
1 Presenter Camera 8 8 3
3 3 1
REMOVE
Enable deep sleep support ?
Figure 9: Camera speed controls can be adjusted in Mira Portal.
Invert Pan Controls
To reverse le and right camera movements when using Mira Connect (highlighted in the figure on the right) enable the invert
pan control option for each camera in the room.
Aveo Systems, Inc. • 4455 Lower Roswell Road #681593 • Marietta, GA 30068
Phone: [phone] • Email: [e-mail] • aveosystems.com 9Copyright © Aveo Systems, Inc. All rights reserved.

SYSTEMS
Mira Connect Integration Guide for
Crestron IV‑CAMA3 Series Camera
Pan/Tilt
Figure 10: Invert the pan control reverses the le and right motion directions.
Camera Tracking
The Crestron IV‑CAMA3 Series Camera supports camera tracking and Mira Connect will automatically show the camera tracking
control on Mira Connect on the cameras page.
The camera tracking user control may be hidden by unchecking the ‘Allow user control of camera tracking’ option on the
Camera’s Options tab.
Aveo Systems, Inc. • 4455 Lower Roswell Road #681593 • Marietta, GA 30068
Phone: [phone] • Email: [e-mail] • aveosystems.com 10 Copyright © Aveo Systems, Inc. All rights reserved.