Crestron CSC-DCEX User manual

Crestron Electronics, Inc. Wiring Guide - DOC. 7516B
15 Volvo Drive Rockleigh, NJ 07647 (2036230)
Tel: 888.CRESTRON 12.13
Fax: [phone] Specifications subject to
www.crestron.com change without notice.
Crestron Roller Shades and Interfaces
Wiring Guide
Further Inquiries
To locate specific information or resolve questions after reviewing this guide, contact Crestron's True Blue Support at
1-888-CRESTRON [1-888-273-7876] or, for assistance within a particular geographic region, refer to the listing of
Crestron worldwide offices at www.crestron.com/offices.
To post a question about Crestron products, log onto Crestron’s Online Help at www.crestron.com/onlinehelp.
First-time users must establish a user account to fully benefit from all available features.
Future Updates
As Crestron improves functions, adds new features and extends the capabilities of the roller shades and interfaces,
additional information may be made available as manual updates. These updates are solely electronic and serve as
intermediary supplements prior to the release of a complete technical documentation revision.
Check the Crestron website periodically for manual update availability and its relevance. Updates are identified as
an “Addendum” in the Download column.
WARNING: To avoid fire, shock, or death; turn off power at circuit breaker or fuse and test that power is off before
wiring!
NOTES: Observe the following points.
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• This product should be installed by a qualified electrician.
PREPARING AND CONNECTING WIRES
Strip the ends of the wires approximately 1/4 in (6 mm). Use care to avoid nicking the conductors. Twist together
the ends of the wires that share a connection. Apply solder only to the ends of the twisted wires. Avoid tinning too
far up the wires or the end becomes brittle.
INTRODUCTION
Refer to the following wiring diagrams when making connections to a Crestron®
CSC-ACEX, CSC-DCEX, CSC-ACCN, CSC-DCCN, CSM-QMT50, or CSM-QMT50-DCEX.
CAUTION: Do not power the device until paper wrapping is removed from the roller
shade assembly.
WIRING CSM-QMT50
Connect the motor pigtail to a dc power source and to Cresnet®. The red wire is +24 V and
the black wire is common.
If desired, use the supplied male and female quick disconnects to create an easy-to-use
disconnection point in the motor’s pigtail wiring.
Typical Wiring Diagram of Crestron CSM-QMT50 Using Separate Power Supply and
Cresnget Connection
24
Y
Z
G
Motor
Pigtail
24G Z Y
Power and Cresnet Connection
from CSA-PWS225,
CSA-PWS450, CSA-PWS300, or
CSA-PWS600
Roller Shade
24 V Power
Supply
24
Y
Z
G
To Cresnet
Motor
Pigtail
24G
Z Y
G
Roller Shade
24 V Power
Supply
24
Y
Z
G
Motor
Pigtail
24G Z Y
Roller Shade
Typical Wiring Diagram of Crestron CSM-QMT50 Using CSA-PWS225 or
CSA-PWS450
WIRING CSM-QMT50-DCEX
Connect the motor pigtail to a dc power source. The red wire is +24 V and the black wire is
common. The data wires (Yand Z) are not connected.
If desired, use the supplied male and female quick disconnects to create an easy-to-use
disconnection point in the motor’s pigtail wiring.
Typical Wiring Diagram for Crestron CSM-QMT50-DCEX Motor

The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, and Cresnet are either trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks,
and trade names may be used in this document to refer to either the entities claiming the marks and
names or their products. Crestron disclaims any proprietary interest in the marks and names of others.
Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2013 Crestron Electronics, Inc.
WIRING CSC-ACCN
Refer to the following illustration for a typical wiring diagram where 120 Vac powers a roller
shade. The roller shade is connected to the CSC-ACCN via RJ-11 cabling. The
CSC-ACCN receives power from Cresnet.
Typical Wiring Diagram for CSC-ACCN
WIRING CSC-ACEX
Refer to the following illustration for a typical wiring diagram where 120 Vac powers a roller
shade. The roller shade is connected to the CSC-ACEX via RJ-11 cabling. The CSC-ACEX
receives power through the RJ-11 cable.
Typical Wiring Diagram for CSC-ACEX
WIRING CSC-DCCN
Refer to the following illustrations for a typical wiring diagram where a CSA-PWS225,
CSA-PWS450, CSA-PWS300, or CSA-PWS600 (all sold separately) supplies Cresnet and
power to the CSC-DCCN. The device can also be powered by a CSA-PWS40 as long as
the 24 and Gterminal on the NET port are not connected. The CSC-DCCN can also be
powered with a CSA-PWS40 power pack (sold separately). Power can be applied to either
the G24 port or NET port. Data is connected to the NET port.
The CSC-DCCN provides power and control to the roller shade.
CAUTION: If the cable needs to be shortened, special care should be taken to ensure
that the cable is properly wired. Follow the color patterns shown in the wiring diagram
below to ensure proper wiring. Improper wiring causes permanent damage to the
connected device and voids the device's warranty.
Typical Wiring Diagram for CSC-DCCN
WIRING CSC-DCEX
Refer to the following illustration for a typical wiring diagram where a CSA-PWS225 or
CSA-PWS450 (both sold separately) supplies power to the CSC-DCEX. The device can
also be powered by a CSA-PWS40, CSA-PWS300, or CSA-PWS600. The CSC-DCEX
provides power and control to the roller shade. Power can be applied to either the front or
back G 24 port.
CAUTION: If the cable needs to be shortened, special care should be taken to ensure
that the cable is properly wired. Follow the color patterns shown in the wiring diagram
below to ensure proper wiring. Improper wiring causes permanent damage to the
connected device and voids the device's warranty.
Typical Wiring Diagram for CSC-DCEX
RJ-11
120 Vac
Roller Shade
NET Port on Rear
of CSC-ACCN
RJ-11
120 Vac
Roller Shade
G 24 + G -
UP
DN SET
SET NET PWR
G 24
Pigtail Wires
(Included
with Motor)
Blue Red Black Gray White
Power Connection from
CSA-PWS225, CSA-PWS450,
CSA-PWS40, CSA-PWS300, or
CSA-PWS600
Roller Shade
G 24 + G -
UP
DN SET
SET NET PWR
G 24
Blue Red Black Gray White
Pigtail Wires
(Included
with Motor)
NET Port on Rear of CSC-DCCN
Cresnet and Power Connection
from CSA-PWS225,
CSA-PWS450, CSA-PWS300 or
CSA-PWS600
Roller Shade
G 24 + G -
UP
DN SET
SET NET PWR
G 24
Blue Red Black Gray White
Pigtail Wires
(Included
with Motor)
NET Port on Rear of CSC-DCCN
(Do Not Connect 24 and G)
CSA-PWS40 Cresnet
Roller Shade
Typical Wiring Diagram for CSC-DCCN