Crestron HBK-3000 User manual

Crestron HBK-3000 & SMK-3000
Hatchback and Swivel Mount Kits
Installation Guide

This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2002 Crestron Electronics, Inc.

Crestron HBK-3000 & SMK-3000 Hatch Back & Swivel Mount Kits
Contents
Hatchback & Swivel Mount Kits: HBK-3000 & SMK-3000 1
Description .......................................................................................1
Supplied Hardware...........................................................................2
Installation........................................................................................2
HBK-3000 Assembly/Installation Procedure........................2
SMK-3000 Assembly/Installation Procedure........................3
Further Inquiries...............................................................................6
Future Updates .................................................................................6
Return and Warranty Policies ..........................................................7
Merchandise Returns / Repair Service ..................................7
CRESTRON Limited Warranty ............................................7
Installation Guide – DOC. 6110 Contents •i

Crestron HBK-3000 & SMK-3000 Hatch Back & Swivel Mount Kits
Hatchback & Swivel Mount Kits:
HBK-3000 & SMK-3000
Description
The Hatchback and Swivel Mount Kits, HBK-3000 and SMK-3000
(each sold separately), are designed for attachment to the Crestron
TPS-3000 tilt touchpanels.
The HBK-3000 hatchback is a sleekly designed rear-cover option that
provides cable management, wire strain relief, and prevents
unauthorized users from disconnecting the touchpanel. The wire exit
hole at the rear of the HBK-3000 is sized to accommodate all cables that
would typically be connected to the touchpanel. These include the
Crestron-furnished 10- and 8-position, Siamese network/video and audio
cable, an RS-232 cable, and a headphone cable. (Cables not provided
with HBK-3000 or SMK-3000 kits.)
The SMK-3000 swivel mount accessory reduces the chance of theft
while improving viewing convenience. The base rotates 330 degrees,
mounts on the desktop, in a lectern, or on a conference table, and
accommodates surface thicknesses from 3/4-inch minimum to
1 3/8-inches maximum, using the hardware provided. The swivel mount
kit includes the same mounting bracket, rear cover, and attaching screws
as the HBK-3000 option, which covers the cable connections. Routing
the cables down through the center of the swivel assembly keeps the
cables completely hidden from the work surface.
Installation Guide – DOC. 6110 Hatchback & Swivel Mount Kits: HBK-3000 & SMK-3000 •1

Hatch Back & Swivel Mount Kits Crestron HBK-3000 & SMK-3000
Supplied Hardware
The hardware supplied in the kits is listed in the following table.
Supplied Hardware of the HBK-3000 and SMK-3000 (Hatchback &
Swivel Mount Kits)
HBK-3000 SMK-3000*
One (1) Metal Bracket One (1) Swivel Mount Assembly
One (1) Plastic Cover One (1) Metal Bracket
Four (4) Screws 4-40 X 3/16 inch One (1) Metal Plate
One (1) Plastic Cover
Sixteen (16) Screws
(4) 4-40 X 3/16-inch
(4) 6-32 X 1/2-inch
(4) 8-32 X 5/8-inch
(4) 8-32 X 1-inch
* The SMK-3000 mounting kit includes a template for preparing the mounting
surface.
Installation
This section provides an installation procedure for each kit. The only
tools required are #1, #2, and #3 Phillips screwdrivers.
HBK-3000 Assembly/Installation Procedure
To attach the HBK-3000 Hatch Back Kit to the TPS-3000 Touchpanel,
refer to the illustration on page 3 and perform the associated procedures.
1. Remove the two screws Afrom the rear of the touchpanel that
correspond to the holes in the mounting tabs of the Metal Bracket.
2. Put the Metal Bracket in position on the rear of the touchpanel
base (mounting holes should align, and standoff posts should be
oriented as shown in the illustration). Secure the Metal Bracket to
the touchpanel using the two screws Aremoved in step 1.
3. Make certain cable connections are secure, put the Plastic Cover
in position with the cables routed through the rear opening. Secure
the cover to the Metal Bracket using the four # 4-40X 3/16-inch
screws Bsupplied.
2 •Hatchback & Swivel Mount Kits: HBK-3000 & SMK-3000 Installation Guide – DOC. 6110

Crestron HBK-3000 & SMK-3000 Hatch Back & Swivel Mount Kits
HBK-3000 Assembly View
SMK-3000 Assembly/Installation Procedure
To attach the SMK-3000 Swivel Mount Kit to the TPS-3000 Touchpanel
and install the assembly on a suitable mounting surface, refer to the
following procedures and the illustration on page 5.
1. Prepare the mounting surface using the template provided with the
kit. The center hole for the swivel assembly should be 2.5-inches
minimum; 2.6-inches maximum. Position the template so that the
edge indicated as ‘front’ aligns with desired front position of the
touchpanel. Observe the dashed line indicating front edge of the
touchpanel base to ensure the touchpanel will not overhang the
mounting surface.
2. If necessary, to prevent errors when reconnecting, label and
disconnect any cables connected to the touchpanel.
3. Place the touchpanel face down on a padded surface to prevent
damage to the display screen. Adjust tilt angle if needed. Avoid
putting pressure on the display housing.
4. Refer to the assembly view for the HBK-3000 Hatchback Kit
above and remove the two screws Afrom the rear of the
touchpanel that correspond to the Mounting Holes in the Metal
Bracket.
Installation Guide – DOC. 6110 Hatchback & Swivel Mount Kits: HBK-3000 & SMK-3000 •3

Hatch Back & Swivel Mount Kits Crestron HBK-3000 & SMK-3000
5. Put the Metal Bracket in position on the rear of the touchpanel
base (mounting holes should align, and standoff posts should be
oriented as shown in the illustration). Secure the Metal Bracket to
the touchpanel using the two screws Aremoved in step 4.
6. Refer to the illustration on page 5, and route the cables from the
interface box up through the Metal Plate, through the mounting
surface and through the Swivel Assembly, then through the area
of the bracket shown in the figure, and connect to the appropriate
touchpanel ports. Route the cables carefully to avoid chafing.
7. Being careful to avoid damage to the cables, attach the Swivel
Assembly to the base of the touchpanel, using the supplied four
#6-32 X 1/2 inch screws Cthrough the swivel assembly standoff
posts into the threaded holes in the touchpanel base. Make certain
the cables are not twisted or crimped and have sufficient slack at
the port connections before fully tightening the screws.
8. Make certain tab Dis positioned to the front of the swivel
assembly, and that it is directly opposite bent tab F, and place the
touchpanel and swivel mount assembly down on the Mounting
Surface.
9. Hold the Metal Plate in position under the mounting surface and
secure the assembly in place using the #8-32 screws Gprovided
(use the 5/8-inch screws for surfaces 3/4-inch to 1 1/8-inches
thick; use the 1-inch screws for surfaces 1 1/8 to 1 3/8 inches
thick). Use screws Eto adjust tension of the swivel assembly.
10.Again, refer to the HBK-3000 illustration on page 3, and put the
Plastic Cover in position and secure to the Metal Bracket using
the four #4-40 X 3/16-inch screws Bsupplied.
4 •Hatchback & Swivel Mount Kits: HBK-3000 & SMK-3000 Installation Guide – DOC. 6110

Crestron HBK-3000 & SMK-3000 Hatch Back & Swivel Mount Kits
SMK-3000 Swivel Mount Kit Assembly Diagram
C
D
E
FRONT
From
Interface Box
To
Touchpanel
Mounting Surface
Swivel
Assembly
Metal Plate
F
G
Bottom of
Touchpanel
Mounting
Holes(2)
A
Mounting
Holes(4)
B
RouteCables
ThroughThis
Opening
Installation Guide – DOC. 6110 Hatchback & Swivel Mount Kits: HBK-3000 & SMK-3000 •5

Hatch Back & Swivel Mount Kits Crestron HBK-3000 & SMK-3000
Further Inquiries
If after reviewing this Installation Guide, you cannot locate specific
information or have questions, please take advantage of Crestron's award
winning customer service team by calling:
• In the US and Canada, call Crestron’s corporate headquarters
at 1-888-CRESTRON [1-888-273-7876].
• In Europe, call Crestron International at [phone].
• In Asia, call Crestron Asia at [phone].
• In Latin America, call Crestron Latin America at
[phone].
• In Australia and New Zealand, call Crestron Pacific at
[phone].
As of the date of manufacture, the HBK-3000 and SMK-3000 have been
tested and found to comply with specifications for CE marking.
Future Updates
As Crestron improves functions, adds new features, and extends the
capabilities of the HBK-3000 or SMK-3000, additional information may
be made available as manual updates. These updates are solely
electronic and serve as intermediary supplements prior to the release of a
complete technical documentation revision.
Check the Crestron website (www.crestron.com) periodically for manual
update availability and its subjective value. Updates are available from
the Downloads | Product Manuals section and are identified as an
“Addendum” in the Download column.
6 •Hatchback & Swivel Mount Kits: HBK-3000 & SMK-3000 Installation Guide – DOC. 6110