Crestron SMK-6X User manual

Crestron SMK-6X
Swivel Mount Kit for TPS-6X
Installation Guide

This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2008 Crestron Electronics, Inc.

Crestron SMK-6X Swivel Mount Kit for TPS-6X
Contents
Swivel Mount Kit for TPS-6X: SMK-6X 1
Introduction ...............................................................................................................................1
Features and Functions................................................................................................1
Specifications ..............................................................................................................1
Physical Description....................................................................................................2
Setup ..........................................................................................................................................3
Supplied Hardware ......................................................................................................3
Installation................................................................................................................... 3
Resources...................................................................................................................................9
Industry Compliance ...................................................................................................9
Further Inquiries .......................................................................................................... 9
Future Updates ............................................................................................................ 9
Return and Warranty Policies ..................................................................................................10
Merchandise Returns / Repair Service ...................................................................... 10
CRESTRON Limited Warranty.................................................................................10
Installation Guide – DOC. 6577A Contents •i

Crestron SMK-6X Swivel Mount Kit for TPS-6X
Swivel Mount Kit for TPS-6X:
SMK-6X
Introduction
Features and Functions
• Designed for attachment to the TPS-6X-DS desktop docking station
• Swivel mount increases security by reducing chance of theft while
improving viewing convenience
• Base rotates 330 degrees
• Mounts on the desktop, in a lectern or on a conference table
• Accommodates surface thickness from 3/4 inch (1.91 cm) minimum to
1 3/8 inches (3.50 cm) maximum, using the hardware provided
• Cables route through center of assembly, keeping cables completely
hidden from work surface
• Customizable swivel range for added security and convenience
Specifications
Specifications for the SMK-6X are listed in the following table.
SMK-6X Specifications
SPECIFICATION DETAILS
Dimensions
Height 2.64 in (6.69 cm)
Width 6.09 in (15.45 cm)
Depth 5.80 in (14.74 cm)
Weight 0.96 lbs (0.44 kg)
Installation Guide – DOC. 6577A Swivel Mount Kit for TPS-6X: SMK-6X •1

Swivel Mount Kit for TPS-6X Crestron SMK-6X
Physical Description
SMK-6X Overall Dimensions
5.80 in
(14.74 cm)
6.09 in
(15.45 cm)
0.39 in
(0.99 cm)
0.44 in
(1.11 cm)
2.64 in
(6.69 cm)
2 •Swivel Mount Kit for TPS-6X: SMK-6X Installation Guide – DOC. 6577A

Crestron SMK-6X Swivel Mount Kit for TPS-6X
Setup
Supplied Hardware
The hardware supplied with the SMK-6X is listed in the following table.
Supplied Hardware for the SMK-6X
DESCRIPTION PART NUMBER QUANTITY
Assembly, Swivel Stop Plate And Screw 4504353 1
Metal, Washer, Keyed, Swivel Stop 4506321 1
Cork/Rubber, Washer, Custom, Swivel 2017614 1
Rubber, Washer, Custom, Swivel 2017615 1
Screw, #08-32 x 3/8”, Steel 2007269 3
Screw, #08-32 x 1/8”, Steel 2017634 2
Washer, Flat, Steel, 7/8-A Narrow,
15/16” Inner Diameter, 1.75” Outer
Diameter, 0.134” Thick
2017633 1
Nut, #7/8”-14, 1-15/16” Hex Diameter,
31/64”H, Steel, Zinc
2017632 1
Screw, #08-8B, 1/2”, Pan, Phil 2017784 6
Template, Overlay, Table Cutout 4504871 1
Installation
To attach the SMK-6X Swivel Mount Kit to the TPS-6X-DS and install the assembly
on a suitable mounting surface, refer to the following procedures.
NOTE: The mounting surface thickness must be 3/4 inch (1.91 cm) minimum to
1 3/8 inches (3.50 cm) maximum using the hardware provided.
Preparing the TPS-6X-DS
1. Remove the four screws on the TPS-6X-DS as shown in the first illustration
on the following page.
2. Carefully remove the rear cover.
3. Slide the grommet out of the bottom of the rear cover and cut the grommet
from the cable.
4. Slide the boot up the cable away from the connector as shown in the second
illustration on the following page.
5. Feed the connector, then the boot and finally the full length of the cable
through the bottom cutout in the base of the TPS-6X-DS.
6. Install the blank grommet provided with your TPS-6X-DS into place on the
rear cover.
7. Replace the boot over the connector.
8. Replace the rear cover and the four screws removed in step 1.
Installation Guide – DOC. 6577A Swivel Mount Kit for TPS-6X: SMK-6X •3

Swivel Mount Kit for TPS-6X Crestron SMK-6X
CAUTION: Use caution when cutting the grommet to prevent damage to the
connecting cable. Damage to this cable can result in loss of functionality in the
TPS-6X.
Preparing the TPS-6X-DS (1 of 2)
Remove These
Screws Using a
1/16" Allen
Wrench
Remove These Phillips
Head Screws Using a
No.1 Phillips Screwdriver
Rear Cover
Grommet
Cable
Preparing the TPS-6X-DS (2 of 2)
Do Not Remove
Rear Cover
Blank Grommet
Bottom Cutout
In Baseplate
Cable
Boot
Connector
4 •Swivel Mount Kit for TPS-6X: SMK-6X Installation Guide – DOC. 6577A

Crestron SMK-6X Swivel Mount Kit for TPS-6X
SMK-6X/TPS-6X-DS Assembly
1. Feed the Connector/Boot and the full length of the cable through the swivel
mechanism tube with the cable positioned between one of the guide pins
and the rearmost screw hole as shown in the illustration below.
2. Attach and secure the swivel mechanism plate to the TPS-6X-DS using the
provided screws.
3. Pull the remaining cable slack down through the swivel mechanism tube.
CAUTION: Ensure that the cable is not pinched at any point between the swivel
mechanism plate and the base of the TPS-6X-DS.
SMK-6X/TPS-6X-DS Assembly Diagram
Cable
Swivel Mechanism
Tube
Connector/Boot
Swivel
Mechanism Plate
Guide Pins
Screws (3) #08-32
(2007269)
TPS-6X-DS
Installation Guide – DOC. 6577A Swivel Mount Kit for TPS-6X: SMK-6X •5

Swivel Mount Kit for TPS-6X Crestron SMK-6X
SMK-6X Swivel Mount Kit Installation
NOTE: The swivel stop plate has a permanently installed limiting screw to prevent
the swivel mechanism plate from spinning continuously in one direction and tangling
the cable attached to the TPS-6X-DS. This permanently installed limiting screw must
be oriented so it is aligned with the rear of the TPS-6X-DS as shown in the
illustration on the following page.
1. Prepare the mounting surface using the template provided with the kit. The
center hole diameter for the swivel mechanism tube should be 7/8 inch
(2.23 cm) minimum, 15/16 inch (2.39 cm) maximum. Position the template
so the edge indicated as the front edge of the table aligns with the desired
front position of the touchpanel. Observe the dashed line indicating the
front edge of the TPS-6X-DS to ensure the touchpanel will not overhang the
mounting surface.
2. Using the six mounting holes on the swivel stop plate as a template, drill
pilot holes 0.093 inch (0.24 cm) minimum, 0.115 inch (0.30 cm) maximum
in diameter, and no deeper than 0.35 inch (0.89 cm). Attach the swivel stop
plate to the bottom of the mounting surface using the six screws provided
with your kit. Pass the swivel mechanism tube down through the mounting
hole and stop plate.
3. Slide the provided hardware up onto the swivel tube in the order indicated
in the illustration on the following page.
NOTE: The keyed metal washer (4506321) will fit onto the swivel mechanism tube
in one of two orientations. Orient the tab on the washer to face the front edge of the
mounting surface.
4. Tighten and adjust the provided nut onto the swivel tube to achieve the
desired resistance on the swivel assembly’s motion. A flat tool (such as a
large flat-head screwdriver) may be used in the slot on the bottom of the
swivel mechanism tube to hold the tube still while tightening the nut.
6 •Swivel Mount Kit for TPS-6X: SMK-6X Installation Guide – DOC. 6577A