Crestron TPS-6X-DSW User manual

CrestronMMK-6X-DSW & WMKM-6X-DSW
MudMountKitsfortheTPS-6X-DSW
InstallationGuide

Crestron MMK/WMKM-6X-DSW Mud Mount Kits for the TPS-6X-DSW
Contents
Mud Mount Kits for the TPS-6X-DSW: MMK-6X-DSW & WMKM-6X-DSW 1
Description.................................................................................................................................1
Setup..........................................................................................................................................2
Supplied Hardware......................................................................................................2
Installation...................................................................................................................4
Resources.................................................................................................................................12
Industry Compliance .................................................................................................12
Reference Documents................................................................................................12
Further Inquiries........................................................................................................12
Future Updates ..........................................................................................................12
Return and Warranty Policies..................................................................................................13
Merchandise Returns / Repair Service ......................................................................13
CRESTRON Limited Warranty.................................................................................13
All brand names, product names and trademarks are the property of their respective owners.
©2009 Crestron Electronics, Inc.
Installation Guide – DOC. 6779A Contents •i

Crestron MMK/WMKM-6X-DSW Mud Mount Kits for the TPS-6X-DSW
Mud Mount Kits for the
TPS-6X-DSW:
MMK-6X-DSW & WMKM-6X-DSW
Description
Mud Mount Kits are the preferred mounting option for the TPS-6X-DSW when the
cutout made in the drywall for docking station installation is too large. These kits
provide support for additional plastering that can be applied to hide large
irregularities in the cutout.
NOTE: If mounting into a material other than drywall (for example, wood lectern,
concrete or rock) use the cutout template, available in the post-construction kit
WMKM-6X-DSW. For concrete and rock mounting material, allow for proper
ventilation before mounting the TPS-6X-DSW.
There are two Mud Mount Kits. The MMK-6X-DSW is a pre-construction
accessory. Pre-construction refers to framed walls prior to hanging drywall. This
accessory must be used with either the Pre-Construction Mount Kit (PMK-6X-DSW)
or Back Box (BB-6X-DSW).
The WMKM-6X-DSW is a post-construction kit. Post-construction refers to framed
walls with drywall hung. This accessory is designed with a mounting plate so that it
can be placed anywhere on a wall without the support of a stud.
NOTE: Since the TPS-6X-DSW contains moving parts, mounting to a stud offers
more support and is therefore highly recommended. Although Crestron®offers the
post-construction WMKM-6X-DSW mounting option, a mounting option that is
secured to a stud, such as the BB-6X-DSW or PMK-6X-DSW is highly
recommended.
NOTE: If necessary, consult the latest revision of the TPS-6X-DSW Operations and
Installation Guide (Doc. 6708) for a complete list of mounting options. The
document is available from the Crestron website (http://www.crestron.com/manuals).
Installation Guide – DOC. 6779A Mud Mount Kits for the TPS-6X-DSW: MMK-6X-DSW & WMKM-6X-DSW •1

Mud Mount Kits for the TPS-6X-DSW Crestron MMK/WMKM-6X-DSW
Setup
Supplied Hardware
The MMK-6X-DSW consists of three parts. These parts produce an assembly that
attaches to the BB-6X-DSW or PMK-6X-DSW. The WMKM-6X-DSW consists of
six parts, three of which make up the MMK-6X-DSW, as well as a mounting plate, a
set of mounting screws and a cutout template.
The mounting plate provides the necessary support for post-construction
applications. An overlay cutout template (4506370) is supplied which is similar to a
frame, the inner area of the frame is the shape of the required opening. Remove the
center of the frame in order to use the template, refer to the illustration on page 4.
Supplied Hardware for the MMK-6X-DSW and WMKM-6X-DSW
DESCRIPTION PART NUMBER QUANTITY
Metal, Plate, Mud Ring 2022809 1
Metal Plate, Adjustment 2017631 2
Hardware, Metal, Push-On 2004121 4
Metal, Plate, Mounting
(WMKM-6X-DSW only) 2022811 1
Screw, #06-32 x 1 1/2”, Pan, Phil
(WMKM-6X-DSW only) 2007254 4
Overlay, Template, Wall Cutout
(WMKM-6X-DSW only) 4506370 1
The dimensions of the MMK-6X-DSW and WMKM-6X-DSW are shown below and
on the next page.
Dimensional Drawing – Mud Ring Plate
6.03 in
(15.31 cm)
7.57 in
(19.22 cm)
10.46 in
(26.57 cm) 8.92 in
(22.66 cm) 1.03 in
(2.63 cm)
2.26 in
(5.73 cm)
4.00 in
(10.16 cm)
0.50 in
(1.27 cm)
0.05 in
(0.13 cm)
2 •Mud Mount Kits for the TPS-6X-DSW: MMK-6X-DSW & WMKM-6X-DSW Installation Guide – DOC. 6779A

Crestron MMK/WMKM-6X-DSW Mud Mount Kits for the TPS-6X-DSW
Dimensional Drawing – Adjustment Plate
0.38 in
(0.95 cm)
0.38 in
(0.95 cm)
10.24 in
(26.01 cm)
Dimensional Drawing – Mounting Plate
10.31 in
(26.19 cm)
8.00 in
(20.32 cm)
0.06 in
(0.15 cm)
8.82 in
(22.39 cm)
6.35 in
(16.13 cm)
Installation Guide – DOC. 6779A Mud Mount Kits for the TPS-6X-DSW: MMK-6X-DSW & WMKM-6X-DSW •3

Mud Mount Kits for the TPS-6X-DSW Crestron MMK/WMKM-6X-DSW
Drywall Cutout Template and Dimensions (supplied with WMKM-6X-DSW only)
7 11/16 in
(196 mm)
9 1/16 in
(230 mm)
6 9/16 in
(167 mm)
6 1/8 in
(156 mm)
Installation
This section provides an installation procedure for each Mud Mount Kit. The
“MMK-6X-DSW Procedure” starts below and the “WMKM-6X-DSW Procedure”
starts on page 7. Be sure to review each procedure before starting.
MMK-6X-DSW Procedure
This section provides the necessary steps for the assembly of the MMK-6X-DSW
with either the BB-6X-DSW or PKM-6X-DSW. It is assumed that the BB-6X-DSW
or PKM-6X-DSW has been secured to the stud according to the instructions in the
latest revisions of their Installation Guides (Doc. 6728 and Doc. 6778 respectively).
It is also assumed that drywall is in place and a cutout for the TPS-6X-DSW is made
in the drywall.
Complete the steps in the order provided. The only tools or materials required and
not supplied are four standard drywall screws, #2 Phillips screwdriver, a level and
tools/material to apply drywall joint compound.
CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity
above and below the TPS-6X-DSW for heat dissipation.
4 •Mud Mount Kits for the TPS-6X-DSW: MMK-6X-DSW & WMKM-6X-DSW Installation Guide – DOC. 6779A

Crestron MMK/WMKM-6X-DSW Mud Mount Kits for the TPS-6X-DSW
NOTE: The illustrations in this procedure show the installation of the
MMK-6X-DSW with the PMK-6X-DSW. Even though the illustrations only show
the PMK-6X-DSW, they are identical for the BB-6X-DSW.
1. Pass an adjustment plate through the opening and align its two center holes
with the top two pins on the PMK-6X-DSW. Verify that the pins on the
adjustment plate are not between (facing) the adjustment plate and the
PMK-6X-DSW. Refer to the illustration below for visual guidance.
Secure Adjustment Plates to PMK-6X-DSW (or BB-6X-DSW)
PMK-6X-DSW
ADJUSTMENT PLATE(2)
(2017631 )
PUSH-ON FASTENER (4)
(2004121 )
NOTE: BACK VIEW
OF INSTALLATION.
2. Slide a push-on fastener over each pin of the PMK-6X-DSW (or
BB-6X-DSW) to loosely secure the adjustment plate and the mounting
plate. Do not push the push-on fasteners all the way down onto the pins.
Slide them on enough to keep the adjustment plate and mounting plate as
one adjustment/mounting plate assembly.
3. Use the second adjustment plate and repeat steps 1 and 2 using the lower
two PMK-6X-DSW (or BB-6X-DSW) pins.
NOTE: When installing into the PMK-6X-DSW, verify that the 18 AWG bus wire
securing the cables for the TPS-6X-DSW remains attached.
4. Insert the symmetrical mud ring plate into the opening, as shown in the
illustration on the following page.
Installation Guide – DOC. 6779A Mud Mount Kits for the TPS-6X-DSW: MMK-6X-DSW & WMKM-6X-DSW •5

Mud Mount Kits for the TPS-6X-DSW Crestron MMK/WMKM-6X-DSW
Insert and Secure Mud Ring Plate into PMK-6X-DSW (or BB-6X-DSW)
PMK-6X-DSW
DRYWALL
MUD RING PLATE
(2022809 )
DRYWALL SCREWS
(NOT INCLUDED)
SCREW LENGTH SHOULD NOT
EXCEED DRYWALL THICKNESS
BY MORE THAN1/2" (13 MM).
5. When the mud ring plate is in position, bend the top two flanges of the plate
upward and the bottom two flanges downward.
• If mounting into the PMK-6X-DSW, bend the flanges approximately
90 degrees.
• If mounting into the BB-6X-DSW, bend the flanges back as far as they
can go.
6. Use four standard drywall screws (length should not exceed drywall
thickness by more than 1/2 inch) to secure the mud ring plate to the rest of
the assembly. The screws pass through the clearance holes in the
PMK-6X-DSW (or BB-6X-DSW) and are secured in the extruded holes of
the adjustment plates.
7. Verify that the mud ring plate is level.
NOTE: Do not overtighten screws. Doing so may over-dimple or rip the mud ring
plate.
8. Use a #2 Phillips screwdriver and tighten the drywall screws by hand so that
they slightly dimple into the holes in the mud ring plate.
6 •Mud Mount Kits for the TPS-6X-DSW: MMK-6X-DSW & WMKM-6X-DSW Installation Guide – DOC. 6779A

Crestron MMK/WMKM-6X-DSW Mud Mount Kits for the TPS-6X-DSW
9. Apply drywall joint compound as needed to finish the cutout. Avoid
covering the four tapped mounting holes.
10. Run the necessary cables for the TPS-6X-DSW and secure them behind the
drywall.
11. When dry, the wall mount docking station can be installed using the four
tapped holes in the PMK-6X-DSW. Refer to the latest revision of the
TPS-6X-DSW Operations and Installation Guide (Doc. 6708) for
installation instructions. Refer also to the comprehensive illustration below.
TPS-6X-DSW Mounting Using MMK-6X-DSW – Exploded View
TPS-6X-DSW
SCREW (4) #06-32 1 1/2"
PAN HEAD(2007254 )
DRYWALL
DRYWALL SCREWS(NOT INCLUDED)
SCREW LENGTH SHOULD NOT
EXCEED DRYWALL THICKNESS BY
MORE THAN1/2" (13 MM).
PMK-6X-DSW NOTE: REQUIRED
ADJUSTMENT
PLATES AND
PUSH-ON
FASTENERS NOT
SHOWN.
MUD RING PLATE
(2022809 )
WMKM-6X-DSW Procedure
This section provides the necessary steps for the assembly and installation of the
WMKM-6X-DSW into a wall. Review the procedure and complete the steps in the
order provided. The only tools or materials required and not supplied are a drywall
saw or equivalent, a level, four standard drywall screws, #2 Phillips screwdriver and
tools/material to apply drywall joint compound.
Installation Guide – DOC. 6779A Mud Mount Kits for the TPS-6X-DSW: MMK-6X-DSW & WMKM-6X-DSW •7

Mud Mount Kits for the TPS-6X-DSW Crestron MMK/WMKM-6X-DSW
CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity
above and below the TPS-6X-DSW for heat dissipation.
1. Insert the two pins on one adjustment plate into the top two outer holes
on the mounting plate, as shown in the illustration below.
Create the Adjustment/Mounting Plate Assembly
ADJUSTMENT PLATE(2)
(2017631 )
MOUNTING PLATE
(2022811 )
PUSH ON FASTENER(4)
(2004121 )
2. Slide a push-on fastener over each pin on the adjustment plate to
loosely secure the adjustment plate and the mounting plate. Do not
push the push-on fasteners all the way down onto the pins. Slide them
on enough to keep the adjustment plate and mounting plate as one
adjustment/mounting plate assembly.
3. Use the second adjustment plate and repeat steps 1 and 2 using the
lower two holes on the mounting plate.
4. Locate an area on the wall that is free of miscellaneous wiring and
studs.
5. Make a small hole near the middle of the designated site; verify that the
location is suitable.
8 •Mud Mount Kits for the TPS-6X-DSW: MMK-6X-DSW & WMKM-6X-DSW Installation Guide – DOC. 6779A