Crestron RFID-USB User manual

The Crestron® RFID-USB is an RFID card reader that integrates into
supported room scheduling applications and custom room control
projects via a TSW-70 series or TSS-70 series touch screen. The
RFID-USBinstalls next to the touch screen, allowing users to easily
authenticate with or communicate to the touch screen by scanning an
RFIDcard. The RFID-USB also integrates with a Crestron control system
for custom room control or access projects.
NOTE:A third-party Quick Start is provided in the box with the
RFID-USBfor compliance purposes only. The Crestron Quick Start
should be used when installing the RFID-USB.
In the Box
1 RFID-USB, RFIDCard Reader
Additional Items
4 Adhesive Pads (2058188)
1 Cable, Micro USBto USBA, 17.72 in. (450 mm)(2058186)
1 Frame, Glass Mount (2058187)
1 Label, Adhesive (2058189)
Install the RFID-USB
The RFIDcan be installed into drywall or onto a flat, smooth surface
such as glass. Procedures for each installation are provided in the
sections that follow.
NOTE:To avoid RF interference, ensure that no metal object or surface
is located within 10 cm of the RFID-USB after installation
Drywall Mounting
The following is required for this installation: a level, a roll of masking
tape, a drill, and a surface cleaning product that does not leave a film.
NOTE:The following procedure assumes that the touch screen has
been installed into drywall using its provided mounting bracket or the
TSW-770/1070-MSMK-ANG multisurface mount kit. For more
information, refer to the TSW-570,TSW-770, and TSW-1070 Quick
Start, the TSS-770 and TSS-1070 Quick Start, or the
TSW-770/1070-MSMK-ANG Quick Start.
1. Clean and dry the mounting surface thoroughly.
2. Select the mounting location for the RFID-USB. The RFID-USBshould
be mounted below the touch screen and should not be mounted more
than 8in. (203 mm) away from the touch screen.
3. Using the level, tape a horizontal reference line on the mounting
surface that aligns with the lower edge of the RFID-USB. Ensure the
reference line is level before proceeding.
4. Drill a 3/4in. (19 mm)diameter hole into the mounting surface at the
center of where the RFID-USB will be mounted.
5. Route the provided USBcable through the drywall from the touch
screen cutout to the hole created in step 4 above. Ensure that the
micro USBend of the cable is routed to the mounting location.
6. Attach the USBA cable end to the touch screen rear housing.
RFID-USB QuickStart
RFIDCard Reader
1

7. Bend the flexible connector on the RFID-USB so it is at a 90° angle.
8. Attach the micro USBcable end to the RFID-USB flexible connector.
9. Remove the protective liner from the four adhesive pads on the
RFID-USB.
CAUTION:The adhesive pads are high-strength bond. Once the
adhesive comes in contact with a surface, it cannot be easily
removed.
10. Hold the RFID-USB at a 45-degree angle to the mounting surface,
and then align the lower edge of the pad with the taped reference
line. Do not allow the adhesive to come in contact with the drywall.
NOTE:The RFID-USBmust be positioned so that the flexible
connector and connected USBcable will enter the cable hole once
the RFID-USBis mounted.
11. Once the RFID-USB is level and aligned with the taped reference line,
press the edges of the device to the mounting surface firmly to
ensure proper adhesion and to eliminate any trapped air bubbles.
2
RFID-USB QuickStart
RFIDCard Reader

Glass Surface Mounting
The mounting procedures for installing the RFID-USBon glass or
another flat, smooth surface differ depending on whether the touch
screen was installed using a multisurface mount kit or a mullion mount
kit. Both procedures are provided.
Multisurface Mount Kit Installation
The following is required for this installation: a level, a roll of masking
tape, and a surface cleaning product that does not leave a film.
NOTE:The following procedure assumes that the touch screen has
been installed onto the glass surface using the TSW-770-MSMK,
TSW-1070-MSMK, or TSW-770/1070-MSMK-ANG multisurface mount
kits. For more information, refer to the TSW-770-MSMK and
TSW-1070-MSMKQuick Start or the TSW-770/1070-MSMK-ANG
Quick Start.
1. Clean and dry the mounting surface thoroughly.
2. Select the mounting location for the RFID-USB and determine
whether raceway (not included) will be exiting the MSMK from the
top, bottom, left, or right knockout to conceal the USBcable. The
RFID-USBshould not be mounted more than 8in. (203 mm) away
from the touch screen.
3. Using the level, tape a horizontal reference line on the glass surface
that aligns with the lower edge of the RFID-USB. Ensure the
reference line is level before proceeding.
4. Use pliers (or a similar tool) to break away the appropriate knockout
on the left, right, or bottom of the MSMK for routing the USB cable
from the RFID-USB to the touch screen.
5. Route the provided USBcable through the MSMKknockout opened in
step 4 above to the touch screen. Ensure that the micro USBend of
the cable is routed to the RFID-USB mounting location.
6. Attach the USBA cable end to the touch screen rear housing.
7. Install any raceway (if using) to conceal the USBcable.
NOTE:To ensure a proper fit, Crestron recommends using raceway
with the following dimensions: 0.45 in. H x 0.77 in. W (11x20 mm).
8. Insert the RFID-USBinto the mounting frame front-side first.
3
RFID-USB QuickStart
RFIDCard Reader

9. Attach the micro USBcable end to the RFID-USB flexible connector.
10. Remove the protective liner from the four adhesive pads on the
RFID-USB.
CAUTION:The adhesive pads are high-strength bond. Once the
adhesive comes in contact with a surface, it cannot be easily
removed.
11. Remove the protective liner from one side of the four additional
adhesive pads, and then attach them to the existing adhesive pads
on the RFID-USB.
12. Remove the protective liner from the other side of the four additional
adhesive pads attached in step 11 above.
13. Hold the RFID-USB at a 45-degree angle to the glass surface at the
orientation it will be mounted, and then align the lower edge of the
device with the taped reference line. Do not allow the adhesive to
come in contact with the drywall.
4
RFID-USB QuickStart
RFIDCard Reader

14. Once the RFID-USB is level and aligned with the taped reference line,
press the edges of the device to the mounting surface firmly to
ensure proper adhesion and to eliminate any trapped air bubbles.
Mullion Mount Kit Installation
The following is required for this installation: a level, a roll of masking
tape, a drill, and a surface cleaning product that does not leave a film.
NOTE:The following procedure assumes that the touch screen has
been installed onto the glass surface using the TSW-770/1070-MUMK
mullion mount kit. For more information, refer to the
TSW-770/1070-MUMKQuick Start.
1. Clean and dry the mounting surface thoroughly.
2. Select the mounting location for the RFID-USB and determine where
raceway (not included) will be installed to conceal the USBcable. The
RFID-USBshould be mounted below the touch screen and should not
be mounted more than 6in. (152 mm) away from the touch screen.
3. Using the level, tape a horizontal reference line on the glass surface
that aligns with the lower edge of the RFID-USB. Ensure the
reference line is level before proceeding.
4. Drill a 1/2 in (13 mm)diameter hole into the mullion where the
USBcable will exit the mullion to the RFID-USB.
5. Route the provided USBcable through the mullion from the touch
screen to the hole created in step 4. Ensure that the micro USBend
of the cable is routed toward the RFID-USB mounting location.
6. Attach the USBA cable end to the touch screen rear housing.
7. Install any raceway (if using) to conceal the USBcable.
NOTE:To ensure a proper fit, Crestron recommends using raceway
with the following dimensions: 0.45 in. H x 0.77 in. W (11x20 mm).
5
RFID-USB QuickStart
RFIDCard Reader

8. Insert the RFID-USBinto the mounting frame front-side first.
9. Attach the micro USBcable end to the RFID-USB flexible connector.
10. Remove the protective liner from the four adhesive pads on the
RFID-USB.
CAUTION:The adhesive pads are high-strength bond. Once the
adhesive comes in contact with a surface, it cannot be easily
removed.
11. Remove the protective liner from one side of the four additional
adhesive pads, and then attach them to the existing adhesive pads
on the RFID-USB.
12. Remove the protective backing from the other side of the four
additional adhesive pads attached in step 10 above.
13. Hold the RFID-USB at a 45-degree angle to the glass surface so that
the flexible connector is facing the mullion, and then align the lower
edge of the device with the taped reference line. Do not allow the
adhesive to come in contact with the drywall.
6
RFID-USB QuickStart
RFIDCard Reader

14. Once the RFID-USB is level and aligned with the taped reference line,
press the edges of the device to the mounting surface firmly to
ensure proper adhesion and to eliminate any trapped air bubbles.
Attach the Label (Optional)
To provide a finished appearance for installations on glass or other
transparent surfaces, install the included adhesive label on the opposite
side of the surface behind the RFID-USB.
To install the label:
1. Clean and dry the rear of the mounting surface thoroughly.
2. Using the level, tape a horizontal reference line on the glass surface
that aligns with the lower edge of the RFID-USB on the opposite side.
Ensure the reference line is level before proceeding.
3. Remove the protective liner from the rear of the label.
CAUTION: The adhesive on the rear of the label is high-strength
bond. Once the adhesive comes in contact with a surface, it cannot
be removed easily.
4. Hold the label at a 45-degree angle to the RFID-USB, and then align
the lower edge of the label with the lower edge of the RFID-USB. Do
not allow the label adhesive to come in contact with the surface.
5. Once the label is level and aligned with the angled bracket, press the
label to the pad firmly to ensure proper adhesion and to eliminate
any trapped air bubbles.
7
RFID-USB QuickStart
RFIDCard Reader

Visit the Product Page
Scan the QR code to visit the product page.
RFID-USB
www.crestron.com/model/6512085
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Regulatory Model: TWN4 Slim
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and/or other countries. Bluetooth is either
a trademark or registered trademark of Bluetooth SIG, Inc. in the United States and/or
other countries. Other trademarks, registered trademarks, and trade names may be
used in this document to refer to either the entities claiming the marks and names or
their products. Crestron disclaims any proprietary interest in the marks and names of
others. Crestron is not responsible for errors in typography or photography.
©2021 Crestron Electronics, Inc.
Doc. 9025A
12/15/21
8
RFID-USB QuickStart
RFIDCard Reader