CREVIS GN-9284 User manual

Quick
Start Guide
G-Series Remote IO
GN-9284
CC-Link IE Field Basic
1
2
3
Introduction
Example
System
Connections
4
Install CSP
Profile
5
PLC Ethernet
Setup
6
Network
Configuration
7
Download
Settings
8
Monitor
Data

Page 2
1 Introduction
1.1 This guide contains brief configuration procedures for the GN-9284 CC-Link IE Field Basic Remote IO adaptor.
This adaptor functions as a slave on programmable logic controllers and other devices that function as a CC-Link IE Field
Basic master. For the purposes of this quick start guide, the focus will be on GX-Works3 compatible products like the iQ-
F and iQ-R PLCs.
2 Example System Layout
2.1 This section is a system example that will be utilized for this guide. For simplicity, the system will be limited to a
master PLC and a single slave GN-9284 adaptor.
PLC: FX5UC-32MT/DSS-TS
Remote IO: GN-9284
Slice #1: GT-1238 8 pt, IN
Slice #2: GT-2328 8 pt, OUT
Slice #3: GT-3424 4 pt, Analog IN
Slice #4: GT-4424 4 pt, Analog OUT
Ethernet
Crevis Remote IO
FX5UC-32/DSS-TS
Figure 2.1: Sample System Layout

Page 3
3 Connections
3.1 Wire the system and field power as in Figure 3.1.
4 Register Profile
4.1 Download the GN-9284 CSPP profile and register in GX-Works3.
Tool Profile Management Register
24 VDC
0 VDC
System Power
0 VDC
Field Power
24 VDC
GND
Figure 3.1: Adaptor Power Connections
Figure 4.1: Register Profile

Page 4
5 PLC Ethernet Setup
5.1 Enter the IP Settings for the PLC in GX-Works3. For details on GX-Works3 reference the software manuals
5.2 GN-9284 IP Address setting
Set DIP switches #1 & #10 to ON. This will set the adaptor IP to 192.168.3.1
Figure 5.1: PLC Ethernet Settings
Figure 5.2: DIP Switch Settings

Page 5
6 Network Configuration
6.1 Enable the CC-Link IEF Basic
6.2 Enter the Network Configuration Settings and add station #1 by dragging in the GN-9284 adapter from the
Module List.
Select these settings;
Points: RX/RY to 64 (1 Occupied Station)
RSVD: No Setting
IP Address: 192.168.3.1
Subnet Mask: 255.255.255.0
Click the Close with Reflecting the Setting button.
Figure 6.1: CC-Link IE Field Basic Settings
Figure 6.2: CC-Link IE Field Basic Configurations

Page 6
6.3 Enter the Refresh Settings and set the CPU Side devices. These settings control where the GN-9284 data is
accessed in the PLC.
RX: X 500 Note: The first digital input on Station #1 will be X500
RY: Y 500 Note: The first digital output on Station #1 will be Y500
RWr: D 4000 Note: The first analog input data on Station #1 will be D4000
RWw: D 5000 Note: The first analog output data on Station #1 will be D5000
6.4 Apply the settings and close the window
7 Download Settings
7.1 Write the parameters to the PLC and reboot the PLC & GN-9284 adaptor.
8 Monitor Data
8.1 Use the GX-Works3 Device/Buffer Memory Batch Monitor or Watch Windows to read/write data to the
GN-9284 adaptor.
Figure 6.3: Refresh Settings

Crevis USA
5220-C E 64th St
Indianapolis, IN 46220
800.xxx.xxx
www.crevis.us
CREVIS.QS.GN-9284.A