Cristec YPOWER 12V/25A User manual

Manuel utilisateur des chargeurs de batteries YPOWER
User manual YPOWER battery chargers
Bedienungsanleitung YPOWER Batterieladegeräte
Manual del usuario cargadores YPOWER
Manuale d’uso caricabatterie YPOWER
YPOWER 12V/16A
YPOWER 12V/25A
YPOWER 12V/40A
YPOWER 12V/60A
YPOWER 24V/12A
YPOWER 24V/20A
YPOWER 24V/30A
S.A.S. CRISTEC
31 rue Marcel Paul - Z.I. Kerdroniou Est
29000 QUIMPER - FRANCE
E-mail: [e-mail]
https://www.cristec.fr
YPO-1M-2M-I

23
1PRECAUTIONS – WARRANTY................................................................................................................... 24
1.1 PRECAUTIONS (WARNING)–PROVISIONS RELATING TO SAFETY ............................................................................. 24
1.2 WARRANTY................................................................................................................................................. 28
2OPERATING-PRESENTATION-INTERFACES.......................................................................................... 29
2.1 OPERATING PRINCIPLE .................................................................................................................................. 29
2.2 OVERVIEW PRESENTATION............................................................................................................................. 30
2.3 USER INTERFACE AREA .................................................................................................................................. 30
3INSTALLATION ............................................................................................................................................ 31
3.1 CHARGER OVERALL DIMENSIONS ..................................................................................................................... 31
3.2WIRING ..................................................................................................................................................31
3.2.1 Cable from the public AC power supply network or generator...................................................... 31
3.2.2 Battery cable ..................................................................................................................................... 33
3.2.3 Precautions regarding electromagnetic disturbance generated by the appliance........................ 34
3.2.4 Cabling principle................................................................................................................................ 34
3.3 SWITCHES SETTING-ADJUSTMENT-INDICATORS................................................................................................... 35
3.3.1 Description ........................................................................................................................................ 35
3.3.2 Setting according to the batteries type ........................................................................................... 36
3.3.3 Temperature compensation............................................................................................................. 36
3.3.4 Factory setting................................................................................................................................... 37
3.3.5 Charging curve................................................................................................................................... 38
3.3.6 Indicators........................................................................................................................................... 39
4EQUIPMENT MAINTENANCE AND REPAIRS......................................................................................... 40
4.1 OVERVIEW ................................................................................................................................................. 40
4.2 EQUIPMENT MAINTENANCE ........................................................................................................................... 40
4.3 EQUIPMENT REPAIRS .................................................................................................................................... 40
5TECHNICAL SPECIFICATIONS.................................................................................................................. 41
CONTENTS

24
1PRECAUTIONS –WARRANTY
The CRISTEC equipment includes the following :
•A box containing the battery charger's electronic function.
•AC input connector
•DC output connector
•This user manual
•Specific packing
This document applies to battery chargers from the YPOWER range as listed on the cover (available in colour on our
website www.cristec.fr).
The manual is intended for users, installers and equipment maintenance staff. Please read this manual carefully before
working on the charger.
This manual should be kept safely and consulted before attempting any repairs because it contains all the information
required to use the appliance.
This document is the property of CRISTEC; all the information it contains applies to the accompanying product. CRISTEC
reserves the right to modify the specifications without notice.
1.1 PRECAUTIONS (WARNING)–PROVISIONS RELATING TO SAFETY
Material class I according to NF EN 60335-2-29 standards.
The requirements for installation are contained in the NFC 15-100
standards and in the specific standard “for pleasure boats –
electrical systems – alternating current installations” ISO13297
reference.
The installation must be carried out by an electrician or a
professional installer.
The AC network must be disconnected before starting any
maintenance work on the equipment.
This equipment is not intended to be used by children.
Main precaution
Before handling
the charger, please read carefully this
manual.
Precautions regarding electric shocks
Risk of electric shock and danger of death: it’s strictly for-
bidden to interfere with the charger when under voltage.

25
Precautions regarding accidental earth leaks
The charger's PE terminal must be earthed and
connected before any other terminal.
The charger must be closed before it is turned on with
the screw provided for this purpose.
Accidental leakage current between phase and earth :
standard NFC15-100 should be followed when installing.
Use the services of an electrician or professional installer
to make the necessary connections. The charger should
be connected to a system having a 30mA differential bi-
polar differential circuit-breaker.
Accidental leakage current between the charge circuit
and the earth : accidental current leakage at the earth
must be detected by means of an independent
protective device outside the charger (a residual current
device or an insulation detector).
The installer should decide on the rating and nature of
the protection according to the risks. Special precautions
should be taken on any installation prone to electrolyse
phenomena. Regulations require the presence of a
battery switch on the outputs of the + and the - poles.
Precautions regarding lightning
In areas highly exposed to lightning, it may be
advisable to install a lightning arrestor upstream of
the charger to safeguard it against irreversible

26
damage.
Precautions regarding overheating of the appliance
This appliance is designed to be mounted on a vertical
wall or partition as indicated herein.
It is imperative that there be a gap of 150mm around
the charger. The installer must ensure
that the
temperature of the air at the input is lower than 65°C
in extreme operating conditions.
Measures should also be taken to allow for the
evacuation of hot air on either side of the charger.
It’s strictly forbidden to put any device on or against
the charger.
The charger must not be installed near a heat source ;
it should be installed in a well-
ventilated area. The
charger's air inlets and outlets must not be
obstructed.
Attention
hot surface : do not touch the charger
during and after its operation (burn hasard).
Precautions regarding dust, seepage and falling
water
The charger should be located so as to prevent
penetration of damp, liquid, salt and dust, any of
which could cause irreparable damage to the
equipment and be potentially hazardous for the user.
The appliance should be installed in a dry and well-
ventilated place.

27
Precautions regarding inflammable materials
The charger should not be used near inflammable
materials, liquids or gases.
The batteries can emit explosive gases : please follow
the manufacturer's instructions carefully when
installing them.
Nearby the batteries : ventilate the area
, do not
smoke, do not use any open flame.
Use fuses as defined in this manual.
Ignition protection (Protection against ignition of
surrounding flammable gases)
YPOWER 12V/40A without option is protected against
ignition of flammable gases following the ISO 8846
standard.
The DC output fuses F500 and F501 should only be
replaced by the following blade fuse :
Label : F500, F501, Quantity : 2
Manufacturer : BUSSMAN
Reference : BK-ATC-25M Rating : 32V-25A
Other precautions
Never attempt to drill or to machine the charger's case
: this may damage components or cause metal chips
or filings to fall on the charger's board.
Do not do anything that is not explicitly stated in this manual.

28
1.2 WARRANTY
CRISTEC waives all liability if the installation rules and instructions for use are not observed.
The warranty applies if the origin of the failure is a fault internal to the charger due to CRISTEC.
The warranty applies for equipment returned to the Quimper plant (France).
The warranty, if confirmed by the expert's report, covers only:
oThe repair (part(s) and labour)of faulty equipment returned to the Quimper plant (France). Only original parts
recognized as being defective will be replaced under the warranty.
oReturn shipping costs after repair (courier, by a carrier of our choice).
The warranty, if confirmed by the expert's report, gives rise only to a repair of the equipment and not to a
replacement of the equipment.
The warranty does not cover any other costs that may have been caused by the malfunction of the equipment, such
as: shipping and packaging, disassembly, reassembly and testing costs, as well as all other costs not mentioned.
Our warranty on no account provides for any form of compensation. CRISTEC shall not be held liable for damage
incurred as a result of using the battery charger.
The warranty does not apply if the origin of the failure is due to an external default (see below). In this case, a repair
estimate will be issued.
Our warranty does not cover :
1. Failure to abide by this manual
2. Any mechanical, electrical or electronic alterations to the appliance
3. Improper use
4. Presence of moisture
5. Failure to comply with AC power-supply tolerances (i.e. overvoltage)
6. Incorrect connections
7. Falls or impacts during transportation, installation or use
8. Repairs carried out by anyone unauthorized by CRISTEC
9. The maintenance in the energy conversion area made by a non-authorized person by CRISTEC
10. Connection of any interface not supplied by CRISTEC
11. The cost of packaging and carriage
12. Apparent or latent damage sustained during shipment and/or handling (any such claims should be sent to the
haulier)
13. Any unjustified return of equipment (no failure on the equipment)
14. Any other causes not listed above

29
2OPERATING-PRESENTATION-INTERFACES
2.1 OPERATING PRINCIPLE
The design of the battery chargers in the YPOWER range is based on a high-frequency split converter that transforms
the AC signal into regulated and filtered DC current. They can operate as a DC power supply.
Once the type of battery and type of charge has been selected, operation of the battery charger is entirely automatic
(unless otherwise specified by the supplier or the manufacturer of the batteries). It can remain connected to the
batteries and does not need to be disconnected when starting up an engine (marine application), because it is
equipped with an integrated separator.
The appliance's output voltage is sufficient to recharge 1, 2 or separate 3 batteries (integrated charge distributor,
separation of batteries). The charger's maximum output is the rated current distributed to each output according to
the connected batteries banks.
Each output can deliver the rated current.
Not all the outputs have to be connected. However, if only one output is used, we recommend interconnecting outputs
+BAT 1, +BAT 2 and +BAT E to one another (optional).

30
2.2 OVERVIEW PRESENTATION
The chargers are divided into 2 zones :
•The user interface zone
•The energy conversion zone (all maintenance in this area is forbidden except with CRISTEC authorization, under
penalty of warranty termination)
Fixing of the charger is made by 4 x M5 round head screws (screw head diameter less than 10 mm).
Center distance : see corresponding drawing in the appendices 3 to 5 depending on model.
CONNECTIONS :
2.3 USER INTERFACE AREA
Chargers YPO 12-16, 12-25 and 24-12 - See appendix 1
Chargers YPO 12-40, 12-60, 24-20 and 24-30 - See appendix 2
AC input terminal : WAGO type
WINSTA reference 770-813
Terminal for temperature probe
STP-NEW-2.8 (option)
Removable front
cover
Mounting by 4 x M5
round head screws
Opening screw for user interface area
(must be screwed to ensure personnel
protection)
User interface area
DC output terminal :
PHOENIX CONTACT PC 16/4-GF-10,16 BK
for models YPO 12-16, 12-25, 12-40, 24-
12, 24-20 and 24-30.
PHOENIX CONTACT PC35 HC/4-GF-15,00
BK for models YPO 12-60.

31
3INSTALLATION
This paragraph deals with installation of the equipment.
Installation and initial commissioning should be carried out by an electrician or professional installer in accordance
with the standards currently in force (for pleasure boats the applicable international standard is ISO13297).
The installer should familiarize himself with this operating manual and inform users of the instructions for use and the
safety warnings set out in the manual.
3.1 CHARGER OVERALL DIMENSIONS
Chargers YPO 12-16, 12-25 and 24-12 - See appendix 3
Chargers YPO 12-40 and 24-20 - See appendix 4
Chargers YPO 12-60 and 24-30 - See appendix 5
3.2 WIRING
When connecting or disconnecting a cable, the charger's power supply must be turned off and the batteries
electrically insulated from the charger.
The references for additional cables and connectors required for the appliance to operate efficiently are provided in
the following paragraphs : failure to comply with these provisions renders the warranty null and void.
3.2.1 Cable from the public AC power supply network or generator
Disconnect AC network before any wiring and connecting of the connector.
All YPOWER battery chargers can operate automatically and equally on single phase networks from 90 to 265VAC and
from 47 to 65Hz.
Generators
The CRISTEC battery chargers are designed to operate from a generator.
Be careful : In some cases, the generators can produce high over voltages, in particular during start-up
phase. Before connecting the charger, please check its compatibility with the characteristics of the
generator : power, voltage, overvoltage, frequency, current, etc.
It’s highly advised to disconnect the charger from the AC network during the generator starting phase.
Any damage to the charger due to a voltage surge will be excluded from the warranty.
Depending on cable lengths, the cross-section of AC power cables must be at least equal to or greater than the values
provided in the table below :
Model
Minimum cross-section for
115VAC
Minimum cross-section
for 230VAC
YPO 12-16, 12-25 and 24-12
3 x 1.5 mm²
YPO 12-40 and 24-20
3 x 1.5 mm²
YPO 12-60 and 24-30
3 x 2.5 mm²
3 x 1.5 mm²

32
The type of cable (H07-VK, MX, etc.) should be defined by the installer according to the application type and applicable
standards.
For applications where the electricity network may be either 115VAC or 230VAC, always choose the cross section
recommended for 115VAC.
Always use cable markers without insulating collars in accordance with installation standards governing AC network
input connections.
The rating of the upstream circuit-breakers should match the equipment's requirements.
Mounting of AC supply connector
The AC input must be made using a WAGO connector type WINSTA reference770-103.
Remarks :
The YPOWER chargers work as soon as they are powered on. (Input cable connected and powered)
The YPOWER chargers stop as soon as they are not under voltage (disconnected from AC network or installation circuit
breaker in OFF position).

33
3.2.2 Battery cable
Disconnect batteries before any wiring and junction of the connector.
Please check the compatibility of voltage, current and setting according to the battery type before switching ON the
charger.
Checking of the charge voltage
Before connecting the batteries to the charger, first check their polarity.
Equally check the battery voltage with a calibrated voltmeter. A too low voltage value on some types of batteries
show irreversible damage and impossibility to recharge.
Any damage due to incorrect connections will be excluded from the warranty.
For battery cables up to 3 metres, the cross-section of the battery cables should be at least equal to or greater than
the values provided in the table below:
Model
Battery cable cross-section
YPO 12-16, 12-25 and 24-12 10mm²
YPO 12-40, 24-20 and 24-30 16mm²
YPO 12-60 35mm²
The installer should choose the type of cable (H07-VK, MX, etc.) according to the type of application and the applicable
standards.
The DC outputs must use a PHOENIX CONTACT connector type. If you do not have 3 batteries, the terminals non-used
bank will remain unconnected.
Model
PHOENIX CONTACT connector reference
YPO 12-16, 12-25, 12-40,
24-12, 24-20 and 24-30
PC 16/4-STF-10,16 BK
YPO 12-60 PC35 HC/4-STF-15,00 BK
PHOENIX CONTACT connector junction
Connect from left to right : -BAT, +BAT E, + BAT 1 and BAT 2.
•- BAT (minus set of batteries)
•+BAT E (plus engine battery)
•+BAT 1 (plus battery set 1)
•+BAT 2 (plus battery set 2)

34
3.2.3 Precautions regarding electromagnetic disturbance generated by the appliance
We recommend a minimum distance of 2m between the charger and any potentially sensitive equipment.
Use shielded cables for all the connections (*). The shielding should be earthed at both the transmitting and the
receiving ends.
Keep cable length and shielding connections to a minimum.
Route cables as close as possible to conductive parts ("loose" cables or loops should be avoided – cables should be
placed against the hull or walls).
Keep power cables separate from battery cables.
Keep power cables separate from control cables (at least 200mm).
The cables should only supply power to this appliance; any deviation to power another appliance is prohibited.
(*)This is a recommendation for installation rather than an obligation. The installing electrician should decide
whether or not to use shielded cable depending on the EMC environment.
3.2.4 Cabling principle
Typical installation
This installation requires a GFCI (Ground Fault Circuit Interrupter), appropriate fuses on batteries and a battery
compartment temperature probe.
Other types of cabling - see appendix 6.

35
3.3 SWITCHES SETTING-ADJUSTMENT-INDICATORS
3.3.1 Description
The YPOWER chargers are equipped with switches to configure the charger according the battery type and the
application.
1= ON
0 = OFF
2charging modes are available :
-The BOOST function enables a faster charge of the batteries. This function is timed controlled (see table here after)
and is automatically switched off when the battery is fully charged : BOOST stops when batteries current < 20% of
charger rated current. The BOOST function can also be disabled by means of a switch (E).
-The REFRESH function enables to apply periodically a voltage step to maintain the battery, to promote its equalization
and prevent from any sulphation. This function is activated by means of a switch (F).
1 = ON
0= OFF

36
3.3.2 Setting according to the batteries type
Switches setting
Description of the
battery type
Voltage* with
BOOST OFF
Voltage* with
BOOST ON
Maximum
duration of
BOOST at
+/- 5% TBOOST
Maximum
duration of
ABSOPTION at
+/- 5% TABS
A
B
C
D
0 0 0 0 Opened type bat
free electrolyte (wet) 13.4V 14.1V 2H 4H
1 0 0 0
Classic sealed type
bat
(Sealed lead)
13.8V 14.4V 2H 4H
FACTORY SETTING
0 1 0 0 GEL type bat 13.8V 14.4V 2H 4H
1 1 0 0 AGM type bat** 13.6V 14.4V 2H 4H
0 0 1 0 Spiral type bat 13.6V 14.4V 2H 4H
1 0 1 0 Tin calcium lead bat 14.4V 15.1V 2H 4H
0 1 1 0 Wintering or standby
sealed bat 13.4V 13.4V 0H 0H
1 1 1 0 Stabilized DC power
supply 12.0V 12.0V 0H 0H
0 0 0 1 SPE1 open type bat 13.2V 14.8V 2H 4H
1 0 0 1
lithium iron phosphate
(LiFePO4) with BMS
(***)
13.8V 14.4V 6H 1H
0 1 0 1 STORMLINE Bat 13.7V 14.5V 2H 6H
0 1 1 1 Booked
1 1 1 1 Booked
(*) Voltage on + BAT 1, + BAT 2 and + BAT E with 10% of the rated current and a tolerance of +/- 1%.
The voltages values must be doubled for 24V batteries.
(**) REFRESH is not advised for certain types of AGM batteries
(***) Battery Management System
Some specific settings are possible – please consult us.
3.3.3 Temperature compensation
The STP-NEW-2.8 probe enables the compensation of Absorption voltage and
Floating Voltage depending on the ambient temperature of the battery room.
The coefficient used is -3mV/°C/element.
Temperature is not compensated when Wintering (or standby sealed bat),
Stabilized DC power supply and lithium iron phosphate (LiFePO4) with BMS settings are selected.

37
3.3.4 Factory setting
The charger's factory settings are:
Sealed type battery (lead sealed)
BOOST in ON position
REFRESH in OFF position
This setting is a compromise for satisfactory recharging of different technologies of batteries :
-Opened classic lead
-Sealed, Gel or AGM
-Spiral sealed
-Lithium iron phosphate (LiFePO4) with BMS
To define the charge in function of your battery, please refer to the chart, paragraph : 3.3.2.
The installer should set the switches (excluding input and output voltage) and possibly adjust the output voltage with
no load using potentiometer R432 (use the appropriate tool to turn the screw of the potentiometer), depending on :
-the type of battery (contact the battery manufacturer if necessary)
-the intended usage
-the cross-section and length of the output cables
-whether or not the boost function is required
For special batteries, call in a professional installer, who will make the specific settings in accordance with the battery
manufacturer's specifications and according to the specifics of the installation.
CRISTEC is not liable for any damage caused to the batteries or for inefficient recharging.

38
3.3.5 Charging curve
BOOST in ON position
With this setting the YPOWER charger delivers a 5-step charge curve IUoU + automatic weekly recycling (switch E) +
return to automatic BOOST : BOOST, ABSORPTION, FLOATING + REFRESH, REBOOST.
V BOOST : BOOST voltage (see table above)
V FLOAT : FLOATING voltage (see table above : voltage with no BOOST)
T BOOST : BOOST maximum duration (see table above – paragraph 3.3.2)
T ABS : ABSORPTION maximum duration (see table above – paragraph 3.3.2 )
BOOST phase :
Starts up automatically when the charger is turned on if the battery is flat. The current is then at maximum output.
ABSORPTION phase :
Begins when the voltage has reached the maximum BOOST level. The current level starts falling.
These two phases combined last a maximum of TBOOST+TABS (depending on setting). If the current falls below 20% of
rated current, the FLOATING phase automatically kicks in. Duration and current intensity depend on how charged the
battery is.
FLOATING phase :
Starts after TBOOST or if output current has reached 20% of the charger's rated current. The voltage switches to the
FLOATING value and the rated current continues to drop.

39
REFRESH phase :
It is an automatic weekly cycle (Inhibited or not by means of switch F) in order to optimize the battery life duration.
It will occur only after a complete recharge cycle (BOOST, ABSORPTION and FLOATING).The charger will generate
automatically a safe timed voltage step every 7 days whatever the position of BOOST switch.
Phase REBOOST :
Automatic phase consisting in coming back to a BOOST voltage if the DC utilizations require it (i.e. after a complete
recharge cycle BOOST, ABSORPTION and FLOATING if a some DC constant consumptions are detected the charger will
restart a new complete charge cycle including a BOOST phase).
This REBOOST phase will be authorized after measuring certain battery voltage during a determined time.
BOOST in OFF position
With this setting, the YPOWER charger produces a single-stage UI type charge curve. It generates a constant voltage,
supplying the current required by the battery(ies). Recharging time depends on the state of the battery, being longer
than when the BOOST is in the ON position.
3.3.6 Indicators
The following led indicators are visible on the front of the appliance for monitoring.
INDICATORS
STATE
MEANING
Green LED 1 "ON"
On Charger is ON
Off
No or poor quality AC current
Input fuse is blown
Internal charger malfunction
Orange LED 2
"BOOST/ABSORPTION"
Flashing (1 sec. ON, 1 sec. OFF) Charger in BOOST phase
(switch E = ‘1’)
On fixed Charger in ABSORPTION phase
(switch E = ‘1’)
Green LED 2
"FLOATING/REFRESH"
On fixed Charger in FLOATING phase
Flashing (1 sec. ON, 1 sec. OFF) Charger in REFRESH phase
(switch F = ‘1’)
Off Internal charger malfunction or output fuse
blown

40
4EQUIPMENT MAINTENANCE AND REPAIRS
4.1 OVERVIEW
This paragraph deals with equipment maintenance and repairs. Proper operation of the product and its service life are
dependent on strict compliance with the following recommendations.
4.2 EQUIPMENT MAINTENANCE
Disconnect the battery charger from the AC network and the batteries before starting any maintenance work.
If appliances are in a dusty atmosphere, vacuum-clean them regularly, since dust deposits may adversely affect heat
dissipation.
Check the state of battery charge every 3 months.
Nuts and screws should be tightened annually to ensure efficient operation of the appliance (particularly in rugged
conditions: vibrations, shocks, high variations in temperature etc.).
4.3 EQUIPMENT REPAIRS
Disconnect the battery charger from the AC power network and disconnect the batteries before undertaking any
repairs.
When fuses have blown, only use fuses of the type and size recommended in this manual.
Please contact CRISTEC or their distributor for any other repairs.
Any repair without CRISTEC prior agreement entails an exclusion of warranty.

41
5TECHNICAL SPECIFICATIONS
YPO 12V-16A, 12V-25A, 24V12A
Part Number YPO12-16 YPO12-25 YPO24-12
Model 12V/16A 12V/25A 24V/12A
recommended battery bank (Ah) 100-200Ah 200-300Ah 100-200Ah
Input
Voltage
Frequency
Input current consumption
230/115VAC
1.1/2.2A 1.7/3.4A 1.7/3.4A
Recommended power for a generator 280W 435W 420W
Power factor
Efficiency
Input fuses
Output
Total rated current (+/-7%) /
Rated power
16A/228W 25A/356W 12A/342W
Charging curve
Battery type
Boost voltage
28.8VDC for lead sealed battery (factory
setting)
Floating voltage
28.8VDC for lead sealed battery (factory
setting)
Regulation tolerance before output
Mosfet splitter and fuse
Peak to peak ripple and noise
Automotive output fuse mounted in
series in minus pole -BAT
1 x 20A/32V (F500) 1 x 30A/32V (F500) 1 x 15A/32V (F500)
Environment
Cooling
Sound level 0
Operating temperature at 230VAC
Storage temperature
Relative humidity
Casing
Dimensions (length, height, depth) /
Weight
236 x 180 x 96 mm / 2.1kg
Fixing center distance
Fixing screw (wall)
Protection factor
PCB protection
Standards
CE declaration of conformity
CE / EMC
CE / Security - Others
Protections
Options
Temperature probe Output voltage compensation : -36mV/°C
Communication
14.4VDC for lead sealed battery (factory setting)
13.8VDC for lead sealed battery (factory setting)
3 : +BAT E, +BAT 1 et +BAT 2 (integrated Mosfet splitter )
1 -BAT
Each bank can be used individually and deliver the rated current
Casing comprises 3 parts :
· Aluminium sink frame
· Thermoplastic body
· Aluminium clasp
T6,3A/250V - SCHURTER MST 250 Ref. 0034.6623 (F101)
IP22
0
up to 70% (95% without condensation)
236 x 180 x 96 mm / 2.1kg
219 x 155 mm
from 90 to 265VAC single-phase automatic
from 47 to 65Hz automatic
1
90% typical
IU or IUoU through internal dip switches (Boost, Absorption, Floating and Refresh – factory setting)
< 2% (at rated conditions)
Lead sealed as factory setting - Gel, AGM, calcium lead, LiFePO4, DC power-supply mode, etc.
Specific request on demand
From -20°C to +60°C, derating from 60°C. Above 65°C, automatic charger switch off, automatic restart when temperature
decreases
Material
From -20°C to +70°C
4 x M5 round head screws
- Against leaking input surges by VDR rupture (voltage dependent resistor) - Not covered by warranty
- Against output polarity reversal by fuse rupture (removable automotive type)
- Against short-cuircuit and surge
- Against abnormal overheating by cutting off the charger (internal temperature probe - automatic restart)
Available on request
< 2% (at rated conditions)
Number of battery bank
CAN BUS interface
EN61204-3
Water-repellent varnish (marine environment)
EN60335-2-29. Pending UL and CSA.
Output voltage compensation : -18mV/°C
Natural (fanless)