Crosley CAHE8ERR410A14 Owner's manual

TABLE OF CONTENTS
Important Safety Instructions ............................. 2-3 Care and Cleaning .......................................... 11
Packaging ........................................................ 4 Energy Saving Ideas ...................................... 11
Normal Sounds ................................................ 4 Before You Call .............................................. 12
Air Conditioner Features ....................................... 5 Major Appliance Limited Warranty ...................... 13
Operating Instructions .......................................... 5-10
Crosley Corpratlon 111 Cloverleaf Dr, Suite 200, Winston-Salem, NC 27103 Te1:336-761-1212 P/N 2020219A2628

ThisUSE&CAREIV]ANUALprovidesspecificoperatinginstructionsforyourmodel,Usetheroomairconditioneronlyas
instructedinthisUSE&CAREIV]ANUALTheseinstructionsarenotmeanttocovereverypossibleconditionandsituationthat
mayoccur,Commonsenseandcautionmustbepracticedwheninstalling,operating,andmaintaininganyappliance
Tile power supply cord with
this air conditioner contains a current
detection device designed to reduce the risk
of fire.
Please refer to the section 'Operation of
Current Device' for details.
In the event that the power supply cord is
damaged, it cannot be repaired. It must be
replaced with a cord from the product
manufacturer.
For Your Safety
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
o!herappliance.Rea__!oductlabelsfor!_ammabH_tyan_o_erwarnings. ................
Prevent Accidents
To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner,
follow basic precautions, including the following:
Avoid fire hazard or electric shock. Do not
use an extension cord or an adaptor plug. Do
• Be sure the electrical service is adequate for the model you have chosen. This information
can be found on the serial plate, which is located on the side of the cabinet and behind the
gril_e
• If the air conditioner is to be installed in a window, you will probably want to dean both
sides of the g,ass first. If the window is a trip,e-track type with ....... panel included,
remove the screen completely before installation.
Be sure tile air conditioner has been securely and correctly installed according to the
separate installation instructions provided with this manual. Save this manual and the
installation instructions for possible future use in removing or reinstalling this unit.
• When handling the air conditioner, be careful to avoid cuts from sharp metat fins on front
and rear coils.
Electrical Information
The complete electrical rating of your new room air conditioner is stated on the seriat plate.
Refer to the rating when checking the electrical requirements.
- Groood,o0 jPro°°.0.....thooi....diti....isproperlygroundedTominimizeshockandfirehazards,proper grounding is important. The power cord is equipped with a three-prong grounding
Do not, under any p,ug for protection against shock hazards.
cireums[anees_ cut_ • Your air conditioner must be used in a properly grounded wall receptacle. If the wall
receptacle you intend to use is not adequately grounded or protected by a time delay fuse
-;_ IO 30A_ remove or bypass the or circuit breaker, have a qualified electrician install the proper receptacle.
• Do not run air conditioner without outside protective cover in place.This could result in
i meehanicat damage within the air conditioner.
DO not use an extension cord or an adapter plug.
DANGER! Avoid Serious Injury or Death
This air conditioner contains no user-serviceabte parts. Atways call an authorized servicer for repairs.
Do not insert or place fingers or objects into the air discharge area in the front of the unit.
Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electricaJ box.
Do not cut or damage the power cord.
If the power cord is damaged, it should only be replaced by an authorized servicer.
In the event of a malfunction (sparks, burning smetI, etc.), immediately stop the operation, disconnect the power cord, and call an authorized
servicer.
Do not operate the air conditioner with wet hands.
• Do not pull on the power cord.
• Do not drink any water that is drained from the air conditioner.

CAUTION! Avoid Injury or damage to the unit or other property
• Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make
units run excessively.
• Do not climb on or place objects on outdoor part of the unit.
• Do not hang objects off the unit.
• Do not place containers with liquids on the unit.
• Turn off the air conditioner at the power source when it will not be used for an extended period of time.
• Periodically check the condition of the unit's installation accessories for any damage.
• Do not apply heavy pressure to the radiator fins of the unit.
• Operate the unit with air filter in place.
•Do not block or cover the intake grille, discharge area and outlet ports.
• Ensure that any electrical/electronic equipment is one yard away from the unit.
• Do not use or store flammable gases near the unit.
i
READTHIS SECTION BEFOREATTEHPTING TO OPERATEAIR CONDITIONER.
Unit must be upright for one hour prior to operating.
Operation of Current
Device
Plug in & "_T""_ _
press RESET
The power supply cord contains a current device that senses damage to the power cord. To test
your power supply cord do the following:
1, Plug in the Air Conditioner.
2, The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will
notice a click as the RESET button pops out.
3, Press the RESET button. Again you will notice a click as the button engages.
4, The power supply cord is now supplying electricity to the unit. (On some products this is also indi-
cated by a Hght on the plug head).
' Always make sure the RESET button is pushed in for correct pperation.
.The p ...... pply cord must be replaced if it fails t ..... t when either the TEST button is pushed,
or it cannot be reset. A new one can be obtained from the product manufacturer.
.If power supply cord is damaged, it CANNOT be repaired, it MUST be replaced by one obtained
from the product manufacturer.
3

Packaging Remove aB packaging from inside the carton, aaong with any
inserts placed into the side louvers.
Remove the plastic ties and foam pad that secure the
compressor to the fan shroud (where applicable). See diagram.
foam pad + plastic ties Packing Inserts
Normal Sounds High pitched Chatter
Today's high efficiency compressors
may have a high pitched chatter
during the cooling cycle,
\
Sound of Rushing Air \\
At the front of the unit, you may \\
hear the sound of rushing air
being moved by the fan.
_bration
Unit may vibrate and make noise
because of poor wall or window
construction or incorrect installation.
Gurgle/Hiss /
"Gurgling or hissing" noise may be
heard due to refrigerant passing
through evaporator during normal
operation.
normal soundsr otherwise it will
void the warranty.

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!U! :i!: !!
Air Conditioner Features ELECTRONICCONTROL
Before you begin,thoroughly familiarizeyourselfwith the controlpanel and remote
as shown below and all its functions, then follow the symbol for the functions you
desire. The unit can be controlled by the touch pad alone or with the remote,
DISPLAYS
TEMPERATURE/TIME CHECK FILTER
FRESET BUTTON
heat romp/timer auto 1
cool thi filter--
econ _reed resel
fen only Io
timer MODE V ON-OFF A FAN SPEED s|eeD
SETS MODE AD3USTS SETS FAN
TEMPERATURE SPEED
OR TIME
STANDARD REMOTE FOR HEAT MODELS
Battery Size; AAA
Warning; Do not mix old and new batteries. Do not mix
alkaline, standard (carbon-zinc), or rechargeable (nickel-
cadmium) batteries.
Operating Instructions
Thefollowing inst!uctions represent the Touch Padt the same instructions can be used for the Remote Control.
TO TURN UNIT ON: YOU WILL SEE:
h_., m '0 ....
_oo/ hi
econ med
fanonly /o
MODE VON-OFF A FANSPEED
\DO THIS;
PRESS ON/OFF BUTTON I
heat
cool
=econ
lan on_
tcmp/timef Fauto =
0 hireed
/o
MODE VON-OFF AFAN SPEED
Note: The unit will run in energy saver(econ) mode when
used for the first time. In this mode, the fan will continue to
run for 1 minute after the compressor shuts off. The fan then
cycles on for 20 seconds at 10 minute intervals until the room
temperature is above the set temperature, at which time the
compressor turns back on, 5

Operating Instructions
(continued)
TO CHANGE TEMPERATURE SETTING;
_emp/_#,,er Faulo =
®me filter
I _ Io reset
IVON=OFF A FAN SPEED s_eep
_--1 /DOTHIS: I
PRESS ATO RAISE |
'PRESS V TO LOWER ]
YOU WILL SEE:
temp/#mer Fauto =
hi filter
reed reset
/o
V ON=OFF A FAN SPEED sleep
Note: Tap or hold either up ( A ) or down ( V ) button until
the desired temperature is seen on the display. This tempe-
rature will be automatically maintained anywhere between
60 °F (16 °C) and 90 °F (32 °C). If you want the display to
read the actual room temperature. See "To Operate on Fan
Only" section on Page 7.
TO AD3UST FAN SPEEDS;
temp/tlmer Fauto =
0 hi
reed
Io
ON=OFF AFAN SPEED
DO THIS:
filter
reset
sleep
PRESS TO SELECT
YOU WILL SEE;
temp/tlmer auto
hi filter
reed reset
/o =
VON=OFF A FAN SPEED sleep
TO USE AUTO FAN FEATURE;
templtimer
F0 o_t_ fi'ter
reed rese(
Io
VON-OFF AFAN SPEED sleep
YOU WILL SEE:
templtimer
Fautt_
med filter
/o reset
VON-OFF AFAN SPEED sleep
DO THIS;
PRESS FAN BUTTON,
CHOOSE AUTO
Note: Fan starts at High Speed and adjusts to a slower
speeds the room temperature dictates. For example, if the
room doesn't get too warm, it will stay at the slowest speed,
If the room temperature rises quickly, such as a door being
opened, it will automatically go to the highest speed. The fan
speeds will re-adiust back to the slowest speed as the room
returns to the original set temperature. Press either the fan
slower or fan faster button to adjust the fan speed manually.

Operating Instructions
(continued)
TO OPERATE ON FAN ONLY: YOU WILL SEE:
heat
cool
=eeon
fan only
tc,.p/timer F®
timer MODE V ON-OFF
ix. DO THIS;
PRESS
MODE BUTTON
CHOOSE
FAN ONLY
A
heal
cod
econ
.[an only
tcmp/tJo_er F®
timer MODE VON-OFF A
Note: Use this function only when cooling is not desired,
such as for room air circulation or to exhaust stale air on
some models. (Remember to open the vent during this
function, but keep it closed during cooling for maximum
cooling efficiency,) You can choose any fan speed you
prefer, (Except "Auto Fan").
During this function, the display will show the actual room
temperature, not the set temperature as in the cooling
mode.
COOL FEATURE:
temp/timer
heat
cool
econ
m]on only
timer MODE V ON=OFF
I x. DO THIS:
PRESS
MODE BUTTON
CHOOSE COOL
YOU WILL SEE:
ternp/tJmer
heat
=cool
econ
Iononly
F®
timer MODE V ON=OFF A
Note: In this mode, the fan remains on all the time with the
compressor cycling on and off when room temperature is
reached.
SLEEP FEATURE:
_emp/timer Fauto
hi =filter
toed reset
Io
VON=OFF A FAN SPEED sleep
DO THIS:
PRESS
SLEEP BUTTON
YOU WILL SEE:
_cmp/dmer Fauto
hi =filter
reed reset
Io
VON-OFF A FAN SPEED sleep
INote: In this mode the selected temperature will increase
by 2 °F 30 minutes after the mode is selected. The tempe-
rature will then increase by another 2 °F after an additional
30 minutes. This new temperature will be maintained for 7
hours before it returns to the originally selected tempera-
ture. This ends the "Sleep" mode and the unit will continue
to operate as originally programmed. The "Sleep" mode
program can be cancelled at any time during operation by
again pressing the "Sleep" button,

Operating Instructions
(continued)
TIHER: DELAY STOP /START FEATURE
heat te.,plO._cr 01
cool
econ
jan otfly Ht
timer MODE V\, ON-OFF _ I
\/
\/THEN
DO THIS;
\FIRST
DO THIS:
PRESS
TIMER BUTTON PRESS
UP/DOWN BUTTONS
YOU WILL SEE HOW HUCH TIHE IS CHOSEN:
heat
cool
eeon
Jan only
templdmer
H, ®
timer MODE V ON-OFF A
Note: For Delay Stop, the unit must be in the On position.
Note: For Delay Start, the unit must be in the Off position,
First, Press TIMER button, then adiust timer setting, tap or hold the UP arrow ( A ) or the DOWN arrow ( V ) to change delay
timer at 0.5 hour increments, up to 10 hours, then at t hour increments up to 24 hours. The control will count down the time
remaining until start (8, 7.5, 7, etc.), The Delay Start Operation automatically selects cooling with maximum Fan speed (if Cool,
Energy Saver, or Fan Only was the last mode selected), The temperature maintained will be the same as previously set. To change
the set temperature, press "COOL" then Up or Down arrows until the desired temperature is indicated on the display. After S
seconds, the control will automatically change the display back to the hours remaining until the unit will start/stop. Pressing the
unit On/Off button at any time will cancel the Delay Start/Stop function, The Delay Start/Stop Feature will work until the unit either
starts or stops. Once that happens the above steps have to be repeated again.
CHECK FILTER FEATURE,YOU WILL SEE:
tem_/fimer Fauto u
hi =filter
reed reset
Io
VON-OFF A FAN SPEED sleep V
Note: This feature is a reminder to clean the Air Filter (See
Care and Cleaning) for more efficient operation, The LED
(light) will illuminate after 250 hours of operation. To reset
after cleaning the filter, press the "Filter Reset" button and
the light will go off.
HEATING FEATURE(on some models):
temp/tlmer
heat
=cool
econ
fan only
timer MODE VON-OFF
temp/limer
ON-OFF
rauto
hi =filter
med reset
lo
AFAN SPE_
/
DO THIS; "I
I
PRESS FILTER
RESET BUTTON
YOU WILL SEE:
heat temp/timer 0 ]
r
cool
econ
fan only
timer MODE VON=OFF
Note: This feature can be used with any combination of FAN
Speeds (Low speed only on 115V models), Timer, or Sleep
Modes, When in the "Heat" mode,the fan will run continuously
while heat is needed, The temperature will automatically be
maintained anywhere between 55 °F(!3 °C) and 80 °F(27 °C)
(The upper limit of temperature could reach 86°F(30 °C) on some
of the 115V models,), When the room set temperature is satisfied,
the fan will cycle off and on to circulate and sample the room air,

Operating Instructions
(continued)
FAULT CODES;
temp/thner te.,p/#,ner te,r,p/tlr,,er temp/time: te:,,p/ti,,,er
F FFFF
ON-OFF ON-OFF ON=OFF ON=OFF ON-OFF
If the display reads "HS", "AS", "ES", "CS" or "OS", a sensor has failed. Contact your Authorized Service Center.
TO CHANGE TEHPERATURE DISPLAY:
temp/tlmer auto
h,.
reed
Io
V _ FAN SPEED
\/DO THIS:
PRESS AND HOLD THE
UP/DOWN BUTTONS
TOGETHER FOR 3 SECONDS
filter
reset
sleep
I
YOU WILL SEE;
temp/timer auto
hi =Creed
Io
filler
reset
VON=OFF AFAN SPEED sleep
Note: The control is capable of displaying temperature in
degrees Fahrenheit or degrees Celsius.
TO TURN UNIT OFF;
temp/tJmer Fauto
hi =filter
med reset
Io
VON-OFF AFAN SPEED sleep
XDO THIS:
PRESS
I ON/OFF BUTTON I
YOU WILL SEE;
temp/timer • ....
hi filler
med reset
Io
ON=OFF AFAN SPEED sleep
Note: Ifthe unit is turned off in heat mode (if applicable) or
fan only mode, it will return to the same setting when it is
turned on again, When the unit is turned off in cool or energy
saver(econ) mode, it will run in energy saver(econ) mode
when it is turned on again, but the setting of temperature
and fan speed will remain.
9

Operating Instructions
(continued)
ADDITIONAL THlrNGS YOU SHOULD KNOW
Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with.
• The "Cool" circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly. /_
This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue
to run during this time,
• There is a 2-Second delay for the compressor shutting down when selecting FAN ONLY/HEAT. This is to cover the possibility of
having to roll through to select another mode.
• The control will maintain the set temperature within 2 degrees Fahrenheit, between 60F and 90F degrees in cool mode, 55F
and 80F degrees in heat mode(the upper limit of temperature could reach 86F degrees on some of the ]_]_5V models).
After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored.
Figure 1 (VENT CLOSED)
Fresh Air Vent Control (on some models)
The Fresh Air Vent allows the air conditioner to:
:. Recirculate inside air - Vent Closed (see Fig, 1)
2. Draw fresh air into the room - Fresh Air (see Fig, 2)
3. Exchange air from the room - Vent Open (see Fig. 3)
Figure 2 (FRESH AIR) Figure 3 (VENT OPEN)
AUGER WHEELS
(8=WAY)
Air Directional Louvers
Air directional louvers control air flow direction. Your air conditioner has the louver
type described below.
Auger Type
The louvers will allow you to direct the air flow Up or Down and Left or Right
throughout the room as needed. Rotate the Auger Wheels until the desired
Left/Right direction is obtained. Pivot horizontal louvers until the desired
Up/Down direction is obtained.