Crosley CCRE312GWWC User manual

Use Care Manual
iiii!i!ii!!ii!iii!iii!i!iii!?
lectric nge
ESIO0 Control with Coil Surface
Elements
Welcome .......................................... 2
important Safety instructions ..... 2-4
Before Setting Oven Controls .... 4-5
Oven Control Functions ............. 5-6
Setting Surface Controls ............... 6
Setting Oven Controls .................... 7
Adjusting Your Oven
Temperature (some models) ............ 8
General Care & Cleaning ......... 8-10
Before You Call
Solutions to Common Problems ........................ 11
Warranty ......................... Back Page
M
READ AND SAVE THESE INSTRUCTIONS pin 316460405 (0707)

WeicorneaCo.gratulatio.s
Serial plate is located behind
the broil or storage drawer on
the lower right side of the
appliance frame.
Congratulations on your purchase of a new range! At Crosley Corporation, we
are very proud of our product and are completely committed to providing you
with the best service possible. Your satisfaction is our number one priority.
We know you'll enjoy your new range and Thank You for choosing our product.
We hope you consider us for future purchases.
PLEASE CAREFULLY READ AND SAVE THESE INSTRUCTIONS
This Use & Care Manual provides specific operating instructions for your model.
Use your appliance only as instructed in this manual. These instructions are
not meant to cover every possible condition or situation that may occur.
Common sense & caution must be practiced when installing, operating &
maintaining any appliance.
Please record your model and serial numbers below for future
reference.
Model Number:
Serial Number:
Purchase Date:
This Use & Care Manual contains general operating instructions for your
appliance and feature information for several models. Your range may not have
all the described features. The graphics shown are representative. The graphics
on your range may not look exactly like those shown.
Product Registration
Be sure to registeryour product. The self-addressed PRODUCT
REGISTRATION CARD should be filled in completely, signed and returned to
Crosley Corporation.
Read all instructions before using this appliance.
Save these instructions for future reference.
This manual contains important safety symbols and instructions. Please pay attention to these symbols and follow all instructions given.
This Symbo! will he!p alert y0u t0 Situations that maY caUse Serious bodily harm, death or property damagel
This sYmb0i Wi!! he!p a!ert YoUto SitUati0ns that may cause bodily inJuiY oi pi0pe[ty damage
•Remove all tape and packaging before using the range. Destroy
the carton and plastic bags after unpacking the range. Never
allow children to play with packaging material.
• Properlnstallation--Be sureyourappliance isproperly installed
and grounded by a qualified technician in accordance with the
National Electrical Code ANSI/NFPA No. 70 latest edition and
local electrical code requirements. Install only per installation
instructions provided in the literature package for this range.
Ask your dealer to recommend a qualified technician and an
authorized repair service. Know how to disconnect the power to
the range at the circuit breaker or fuse box incase of an emergency.
•User servicing--Do not repair or replace any part of the
appliance unless specifically recommended in the manuals.
All other servicing should be done only by a qualified technician.
This may reduce the risk of personal injury and damage to the
range.
•Never modify oralter the construction of a range by removing
leveling legs, panels, wire covers, anti=tip brackets/screws, or
any other part of the product.

• Allrangescantip.
• Injurytopersonscouldresult.
• Installanti-tipdevicepackedwithrange.
• SeeInstallationInstructions.
_To reducetheriskof
tipping,therangemustbesecuredby
properlyinstalledanti-tipbracketprovided
withtherange.Tocheckifthebracketis
installed properly, visually check that rear
leveling leg is inserted into and fully
secured by the anti-tip bracket by
removing lower panel or storage drawer.
For models with a warmer drawer, grasp
the top rear edge of the range and
carefully attempt to tilt it forward. Refer to
the installation instructions for proper anti-
tip bracket installation. J
Stepping, leaning or sitting on the doors or
drawers of this range can result in serious injuries and also
cause damage to the range. Do not allow children to climb or play
around the range. The weight of a child on an open door may
cause the range to tip, resulting in serious burns or other injury.
Do not use the oven or warmer drawer (if
equipped) for storage.
Do not store items of interest to children in the
cabinets above a range oron the backguard of a range. Children
climbing on the range to reach items could be seriously injured.
Never Use YourAppliance forWarming orHeating
the Room.
• Storage in oron Appliance--Flammable materials should not
be stored in an oven, warmer drawer, near surface units or in
the storage drawer. This includes paper, plastic and cloth items,
such as cookbooks, plasticware and towels, as well as flammable
liquids. Do not store explosives, such as aerosol cans, on or near
the range.
• Do Not Leave Children Alone--Children should not be leftalone
or unattended in the area where appliance is in use. They
should never be allowed to sit or stand on any part of the
appliance.
• DO NOTTOUCH SURFACE UNITS,AREAS NEARTHESE UNITS,
HEATING ELEMENTS OR INTERIOR SURFACES OFTHE OVEN.
Both surface units and oven heating elements may be hot even
though they are dark in color. Areas near surface units may
become hot enough to cause burns. During and after use, do not
touch, or let clothing or other flammable materials touch these
areas until they have had sufficient time to cool. Among these
areas are the cook top, surfaces facing the cook top, the oven vent
openings and surfaces near these openings, oven door and
window.
-Wear Proper Apparel--Loose=fitting or hanging garments
should never be worn while using the appliance. Do not let
clothing or other flammable materials contact hot surfaces.
- Do Not Use Water or Flour on Grease Fires--Smother the fire
with a pan lid, or use baking soda, a dry chemical or foam=type
extinguisher.
- When heating fat or grease, watch it closely. Fat or grease may
catch fire if allowed to become too hot.
- Use Only Dry Potholders--Moist or damp potholders on hot
surfaces may result in burns from steam. Do not let potholders
touch hot heating elements. Do not use a towel or other bulky cloth
instead of a potholder.
- Do Not Heat Unopened Food Containers--Buildup of pressure
may cause container to burst and result in injury.
- Remove the oven doorfrom any unused range if it isto be stored
or discarded.
IMPORTANT--Do not attempt to operate the range during a
power failure. If the power fails, always turn off the range. If the
range is not turned off and the power resumes, the range will begin
to operate again. Once the power resumes, reset the clock and
oven function.
IMPORTANT INSTRUCTIONS FOR USING YOUR
COOKTOP
•Knowwhich knob controls each surface heating unit. Place a
pan of food on the unit before turning it on, and turn the unit off
before removing the pan.
•Use Proper Pan Size--This appliance is equipped with one or
more surface units of different sizes. Select utensils having flat
bottoms large enough to cover the surface unit heating element.
The use of undersized utensils will expose a portion of the
heating element to direct contact and may result in ignition of
clothing. Proper relationship of utensil to element will also
improve efficiency.
Utensil Handles Should Be Turned Inward and Not Extend Over
Adjacent Surface Elements--To reduce the riskof burns, ignition
of flammable materials, and spillage due to unintentional contact
with the utensil, the handle of the utensil should be positioned so
that it isturned inward, and does not extend over adjacent surface
units.
• Never Leave Surface Elements Unattended at High Heat
Settings--Boilovers cause smoking and greasy spillovers that
may ignite, or a pan that has boiled dry may melt.
• Do Not Immerse or Soak Removable Heating Elements--
Heating elements should never be immersed in water. Heating
elements clean themselves during normal operation.
• Glazed Cooking Utensils--Only certain types of glass, glass/
ceramic, ceramic, earthenware, or other glazed utensils are
suitable for cook top service without breaking due to the sudden
change in temperature. Check the manufacturer's
recommendations for cook top use.
• When flaming foods underaventilating hood, turn the fan on.

IMPORTANT iNSTRUCTiONS FOR USINGYOUR
OVEN
• Use Care When Opening Oven Door or Warmer Drawer (if
equipped)--Stand to the side of the range when opening the door
of a hot oven. Let hot air or steam escape before you remove or
replace food in the oven.
• Keep Oven Vent Ducts Unobstructed. The oven vent is located
under the left rear surface element if your model isequipped with
coil elements. The oven vent is located below the backguard for
models equipped with ceramic-glass cook tops. Touching the
surfaces in this area when the oven is operating may cause
severe burns. Also, do not place plastic or heat-sensitive items
on or near the oven vent. These items could melt or ignite.
•Placement of Oven Racks. Always place oven racks in desired
location while oven is cool. If rack must be moved while oven is
hot use extreme caution. Use potholders and grasp the rack with
both hands to reposition. Do not let potholders contact the hot
heating elements in the oven. Remove all utensils from the rack
before moving.
•Do not use the broler pan without its insert. The broiler pan and
its insert allow dripping fat to drain and be kept away from the high
heat of the broiler.
•Do not cover the broiler insertwith aluminum foil. Exposed fat
and grease could ignite.
•Protective Liners--Do not use aluminum foil to line the oven
bottom. Only use aluminum foil as recommended in this manual.
Improper installation of these liners may result in risk of electric
shock, or fire.
IMPORTANT INSTRUCTIONS FOR CLEANING
YOUR RANGE
•Clean the range regularly to keep all parts free of grease that
could catch fire. Pay particular attention to the area underneath
each surface element. Do not allow grease to accumulate.
•Kitchen cleaners and aerosols--Always follow the
manufacturer's recommended directions for use. Be aware
that excess residue from cleaners and aerosols may ignite
causing damage and injury.
•Clean Ventilating Hoods Frequently--Grease should not be
allowed to accumulate on the hood or filter. Follow
manufacturer's instructions for cleaning.
COIL COOK TOP MODELS
• Make Sure Reflector Pans or Drip Bowls Are in Place--Absence
of these pans or bowls during cooking may subject wiring or
components underneath to damage.
•Protective Liners--Do not use aluminum foil to line surface unit
drip bowls, or reflector pans. Only use aluminum foil as
recommended in this manual. Improper installation of these
liners may result in risk of electric shock, or fire. Improper
installation of these liners may result in risk of electric shock, or
fire.
IMPORTANT SAFETY NOTICE
The California Safe Drinking Water and Toxic Enforcement Act
requires the Governor of California to publish a list of substances
known to the state to cause cancer, birth defects or other reproductive
harm, and requires businesses to warn customers of potential
exposure to such substances.
i iii i i
The Element ON Indicator Light
The Coil Cook Top range is equipped with a surface control light that will glow on your range--
the Element ON indicator light. The Element ON indicator light (all models) located on the
control panel, will glow when any surface element is turned ON. A quick glance at this lig ht after
cooking is an easy check to be sure all surface controls are turned OFF.
Oven Vent Location
For models equipped with coil surface elements, the oven vent is located under the left
rear surface element. When the oven is on, warm air flows through the left rear
element. This venting is necessary for proper air circulation in the oven and good baking
results. DO NOT BLOCK THE OVEN VENT.
Arranging Oven Racks
ALWAYS ARRANGE OVEN RACKS WHEN THE OVEN IS COOL (PRIOR TO OPERATING THE OVEN). Always use oven
mitts when using the oven.
Removing & Replacing Oven Racks
To remove, pull the rack forward until it stops. Lift up front of rack and slide out. To replace, fit the rack onto the guides on
the oven walls. Tilt the front of the rack upward and slide the rack back into place.

Arranging Oven Racks
To bake on a single rack, place the rack on position 2 or 3. To bake on 2 racks,
place the racks on positions 1 & 3.
Recomended Rack Positions for Broilinq, Baking & Roastinq:
Food Rack Position
Broiling meats, chicken or fish. (See Broiling section)
Cookies, cakes, pies, biscuits & muffins. 2 or 3
Frozen pies, angel food cake, yeast, bread, casseroles, small
cuts of meat or poultry. 1
Turkey, roast or ham. 1 or Roasting Shelf
Note: The time of day must first be set in order to operate the oven
BAKE PAD--Used to UP & DOWN ARROW PADS-- Used along with
select the bake the function pads to select oven temperature,
function, time of day, clean time & minute timer.
BROIL
PAD--
Used to
select the
variable
broil
function.
TIMER ON/OFF PAD-- CLOCK SET
Used to set or cancel the PAD-- Used
minute timer. The minute to set the time
timer does not start or of day.
stop cooking.
@©©O
,.J
CLEAR/OFF -- Used to
clear any function
previously entered except
the time of day and minute
timer. Press CLEAR/OFF to
stop cooking.
READ THE INSTRUCTIONS CAREFULLY BEFORE USING
THE OVEN, For satisfactory use of your oven, become familiar
with the various functions of the oven as described below.
To Set the Clock
When the range is first plugged in, or when the power supply
to the range has been interrupted, the display willflash "12:00".
1. Press @.
2. Within 5seconds, press and hold the O or until the
correct time of day appears in the display.
To Set the Minute Timer:
1. Press @.
To Set the Minute Timer (cont'd):
time in 10 minute increments. The timer can be set for
any amount of time from 1 minute to 11 hours and 59
minutes.
,
,
Note: If you press the first, the timer will advance
to 11 hours and 59 minutes.
The display shows the timer count down in minutes
until one minute remains. Then the display will count
down in seconds.
When the set time has run out, the timer will sound a 3
second beep. 0:00 will appear in the display until @
is pressed.
Note: While the minute timer is counting down, the ":" will
flash. The minute timer does not start or stop cooking. It
serves as an extra timer in the kitchen that will beep when
the set time has run out. The minute timer can be used
alone or during any of the other oven functions. When the
minute timer is in use with any other function, the minute
timer will be shown in the display. To view other functions,
press the pad for that function.
To Change the Minute Timer while it is in use:
While the timer is active and shows in the display, press
and hold the or to increase or decrease the time.
To Cancel the Minute Timer before the set time has
run out: Press _.
2. Press the to increase the time in one minute
increments. Press and hold the to increase the

/i : ovo.co. , .o,o.s : b:7/:
Note: The time of day must first be set in o@er to opeiate the oven
Changing the Temperature Display Mode (some models)
The electronic oven control temperature display mode was factory preset to display (Fahrenheit) °Foven tempertaures.
Note: Oven cooking temperatures may be set from 170°F to 550°F (77°C to 287°C).
To change the Temperature Display Mode to °C (Celsius) or from °C to °F (do not use Bake or Broil while changing
the Temperature Display Mode):
1. Press&holdthe@ key pad for 6-8 seconds until For Cappears in the display. Note: At this time the display will
show the current Temperature Display Mode whether set for For C.
2. Press the A key pad once to choose the (Fahrenheit) °F mode; or press the V key pad once to choose the
(Celsius) °C mode.
3. After 5 seconds, the display will flash. To accept the change, wait 5 more seconds until the oven control beeps once.
To complete the change skip step 4 below, OR;
4. Ifat any time during the process of changing the Temperature Display Mode (For C) you decide the change is not
desired, press the @ key pad before the oven control beeps once to cancel the process.
5. The control will beep once. The display will then return to the time of day with any temperature display mode change
you may have requested.
/£/! ¸¸¸¸¸¸¸%¸¸¸¸¸¸¸¸¸¸¸¸¸/<
SettingSurface Controls
rv_
OFF
4 6
Fig. 1
Do not place
plastic items such as salt and
pepper shakers, spoon holders or
plastic wrappings on top of the
range when it is in use. These
items could melt or ignite.
Potholders, towels or wooden
spoons could catch fire if placed
too close to the element.
To Operate the Surface Elements
1. Place cooking utensil on the surface element.
2. Push in and turn the surface control knob in either direction to the desired setting
(See Fig.l). Start most cooking operations on a higher setting and then turn to a
lower setting to finish cooking. The control knobs do not have to be set exactly on
a particular setting. Use the settings as a guide and adjust the control knob as
needed.
3. When cooking is completed, turn the surface element off before removing the pan.
Note: The surface "Element On" indicator light(s) will glow when one or more
elements are turned ON. A quick glance at these indicator light(s) when cooking is
finished is an easy check to be sure all surface elements are turned OFF.
Suggested Surface Control Settings
The suggested settings found in the chart below are based on cooking in medium-
weight metal pans with lids. Settings may vary when using other types of pans. Note:
The size and type of utensil used, and the amount and type of food being cooked will
influence the setting needed for best cooking results.
Surface Control Settings
Setting Type of Cooking
HIGH (HI - 9) Start most foods, bring water to a boil, pan broiling
MEDIUM HIGH (7- 8) Continue a rapid boil, fry, deep fat fry
MEDIUM (5- 6) Maintain a slow boil, thicken sauces & gravies, steam
vegetables
MEDIUM LOW (2 -4) Keep foods cooking, poach, stew
LOW (LO - 1) Keep warm, melt, simmer.

sot,,.go o,.co,.t o .
Note: The time of day muStfiiSi be se!! n ord er too perat e the ore n:
To Set or Change the Temperature for Baking
The oven can be programmed to bake at any temperature
from 170°F to 500°F.
To Set the Controls for Baking:
1. Press ,, _ O,,appears in the display.
2. Within 5 seconds, press the or . The display
will show "350°F. '' By pressing and holding the or
}, the temperature can then be adjusted in 5°F
increments.
3. When the or is released, the oven will begin
.
heating to the selected temperature. When the
displayed temperature reaches the desired baking
temperature, the control will beep once (1 time).
To cancel the baking function, press @.
To Change the Oven Temperature after Baking has
Started:
1. Press
displayed.
2. Press the
and make sure the bake temperature is
or to increase or decrease the set
ternperature.
Broiling
1. Arrange oven rack while oven isstill cool. Position the rack as suggested in the
chart below. See "Arranging Oven Racks" in Before Setting Oven Controls,
To insure proper results
when broiling use approved Broil Pan &
Insert (some models).
The broiler pan & the insert (some
models) allows grease to drain and be
kept away from the high heat of the
broiler. DO NOT use the pan without the
insert. DO NOT cover the insert with foil;
the exposed grease could ignite.
Rack Position Food
3 or 4 Medium-rare steaks
3 Fish, medium-well done hamburgers & chops
1 or 2 Well-done foods such as chicken & lobster
.
3.
Press ),
Press and hold the or O until the desired broil setting level appears in
the display. Press the forHI broil or the forLO broil. Most foods can
be broiled at the HI broil setting. Select the LO broil setting to avoid excess
browning or drying of foods that should be broiled to the well-done stage.
4. Place the insert on the broiler pan (some models), then place the food on the
insert. DO NOT use the broiler pan without the insert or cover the insert with
aluminum foil. The exposed grease could ignite.
5. Place the pan on the oven rack. Open the oven door to the broil stop
position when broiling (see illustration).
6. Broil on one side untilfood isbrowned; turn and cookon the second side. Note:
Always pull the rack out to the stop position before turning or removing food.
7. When broiling is finished, press (_.
Should an oven fire occu r,close the oven door and turn off the oven.
If the fire continues, use a fire extinguisher. DO NOT put water or flour on the fire.
Flour may be explosive.
7

Yournewovenhasbeenfactorycalibratedandtestedtoensureanaccuratebakingtemperature.Forthefirstfewuses,follow
yourrecipetimesandtemperaturerecommendationscarefully.Ifyoufeelyourovenistoohotortoocoolfromyourbaking
experience,theoventemperaturemaybeadjustedtoyourliking.
Note:DONOTadjustyouroventemperaturebasedonoventhermometers,suchasthosefoundingrocerystores,theymay
notbeaccurate.
ToAdjusttheOvenTemperature(donotuseBakeorBroilwhileadjustingtheoventemperature):
Press&holdthe_ keypadandreleaseafterthe displaybeginsflashingthefactorytemperaturesetting
1. of OO.
Note: If the oven temperature has been previously adjusted from the factory setting, the current temperature adjusted value
will flash in the display instead.
2. You may increase the oven temperature in 5°F increments with each press ofthe/_ key pad to amaximum oven adjustment
of +35°F. You may also adjust the oven temperature downward in 5°F increments with each press of the V key pad (total
adjustment range of -35to ÷35 F. Note: Your oven control was factory set in the (Fahrenheit) °F Temperature Display Mode.
To change for (Celsius) °C, see Changing the Temperature Display Mode in the Oven Control Functions section of this
Use & Care Manual.
3. If no other key pad is pressed after 5 seconds the display will begin to flash.
you do not want to keep the display adjustment, press the @ key pad before the oven control beeps. This will cancel
4. If
the temperature adjustment procedure. To start this procedure over again begin with step 1 above OR;
5. If you want to keep the adjustment, wait until the display quits flashing and the oven control beeps once.
6. The oven temperature adjustment has be accepted by the oven control and the display will return to the time of day.
Notes: The oven temperature adjustment may be made if your oven control has been set to operate in the (Celsius) °C
Temperature Display Mode. Inthis case each press of the/_ or V key will adjust in 1°C increments upward (maximum
+18°C) or downward (maximum -18°C), depending on which arrow key pad is pressed.
Surfaces How to Clean
Glass, Painted
Plastic Body Parts &
Control Knobs
For general cleaning, use a soft cloth, clean with mild dish detergent & water or a 50/50 solution
of vinegar & water. Follow by rinsing the area with clean water; dry & polish with a soft cloth.
Glass cleaners may be used if sprayed on a soft cloth 1st. DO NOT spray liquids directly on the
control pad and display areas. DO NOT use large amounts of water on the control panel - excess
water on the control area may cause damage to the appliance. DO NOT use other liquid
cleaners, abrasive cleaners, scouring pads, or some paper towels - they will damage the finish.
Painted Control
Panels & Display
areas
Before cleaning the control panel turn all controls to OFF & remove the control knobs. To
remove, pull each knob straight off the shaft. Use the general cleaning instructions provided in the
paragraph above.
Porcelain Enamel
Burner Grates,
Cooktop Surface,
Below Cooktop,
Broiler Pan &Insert,
Broiler Drawer, Door
Liner & Oven Bottom
Clean burner grates, broiler pan & insert in the dishwasher and dry upon removal. If soils are not
removed, follow the cooktop cleaning instructions below.
Gentle scouring with a soapy scouring pad will remove most spots. Rinse with a 1:1 solution of
clean water & ammonia. If necessary, cover difficult spots with an ammonia-soaked paper towel
for 30 to 40 minutes. Rinse with clean water and a damp cloth, then scrub with a soap-filled
scouring pad. Rinse & wipe dry with a clean cloth. Remove all cleaners or the porcelain may
become damaged during future heating. DO NOT use spray oven cleaners on the range top.

(Cleaning Chart cont'd) .............................................
Surfaces How to Clean
Oven Racks Remove racks. See "Removing & Replacing Oven Racks" under Before Setting Oven Controls. Use a
mild, abrasive cleaner, following the cleaner's recommendations. Rinse with clean water & let dry. After
cleaning the racks, rub the sides of the racks with wax paper or a cloth containing a small amount of baby
oil or salad oil (this will make the racks glide easier into the oven rack positions).
Oven Door Use soap & water to thoroughly clean the top, sides & front of the oven door. Rinse well. You may use a
glass cleaner on the outside glass of the oven door. DO NOT immerse the door in water. DO NOT spray
or allow water or the glass cleaner to enter the door vents. DO NOT use oven cleaners, cleaning
powders or any harsh abrasive cleaning materials on the outside of the oven door. DO NOT clean the oven
door gasket. The oven door gasket is made of a woven material, on Self-Cleaning models, which is
essential for a good seal. Care should be taken not to rub, damage or remove this gasket.
Stainless
Steel Clean stainless steel with hot soapy water & a dishcloth. Rinse with clean water and a cloth. DO NOT use
cleaners with high conecentrations of chlorides or chlorines. DO NOT use harsh scrubbing cleaners. Only
use kitchen cleaners that are especially made for cleaning stainless steel. Always be sure to rinse the
cleaners form the surface as bluish stains may occur during heating that cannot be removed.
Be sure the range is cool
before removing elements or drip bowls.
Be careful notto bend terminal ends when
replacing elements after cleaning.
Cleaning Recommendations for Coil Element Cooktop
Surface elements can be unplugged and removed to make cleaning the drip pans easier. The surface elements clean themselves
when they are turned on. Food spilled on a hot element will burn off. Food spilled on a cool element may be cleaned with a damp
cloth--any remaining soil will burn off the next time the element is used.
Never immerse a surface element in water.
Removing the Surface Elements & Drip Bowls
1. Lift the edge of the drip bowl across from the terminal end. Lift the surface
element & drip bowl together just enough to clear the cooktop.
2. While holding the drip bowl and surface element, gently pull the terminal end
out from theterminal plug. Ifequipped, DO NOT remove the hold down clip from
the drip bowl.
Hold
Down
Clip
(if equipped)
Allow Element
Support to rest
on drip pan
inside r_m,
Terminal End
Main top
Lift-up rod
When lowering the lift-up
range top, grasp the sides with finger-tips
only. Be careful not to pinch fingers. DO
NOT drop or bend the range top when
raising or lowering. This could damage
the surface.
Cleaning the Drip Bowls
Wash in hot soapy water or in the dishwasher. Rinse & dry while still warm.
Hard to remove or burned on soil can be removed by soaking the drip bowls for
about 20 minutes in a lightly diluted liquid cleanser or a solution of ammonia &
water (1/2 cup ammonia to 1 gallon of water). A nylon scrubber may be used
after soaking. DO NOT use abrasive cleaners or steel wool, as they will scratch
the surface. Always rinse with clean water & polish dry with a soft cloth.
Replacing Drip Bowls & Surface Elements
1. Slide the terminal end on the element through the opening in the drip bowl.
2. Align the element support to rest on the rim inside the drip bowl. If your drip
bowl is equipped with a hold down clip, align the element support opposite
the terminal end with the slot in the hold down clip & snap into place.
3. After the element is positioned in the drip bowl, line up the terminal end
with the terminal plug as shown.
4. Hold the surface element & drip bowl together as level as possible & firmly
push the terminal end into the terminal plug. Make sure element terminal is
seated properly into terminal plug. Make sure the surface element is level
to reduce the hazard of pans sliding off the element.
Raising the Top for Cleaning
1. Grasp the sides &lift from the front. Lift-up rods will support the top in a
raised position. Only lift the top far enough to allow the support rods to
snap into place.
2. Clean underneath using a clean cloth & hot soapy water.
3. To lower the top, gently push back on each rod to release the notched
support. Hold the range top and slide the lift rods down into the range
frame. 9

Cleaning the Oven Bottom
The bake element isdesigned to be gently tilted up using your hand from the front of
the bake element. This will allow easier access to the oven bottom for cleaning. Be
careful not to raise the element more than 4 or 5 inches from the resting position.
Care &Cleaning of Stainless Steel
Some models are equipped with stainless steel exterior parts. Special care and
cleaning are required for maintaining the appearance of stainless parts. Please
refer to the Cleaning Chart provided at the beginning of the General Care &
Cleaning section in this Use & Care Manual.
/
The baking
element
may be tilted
about 4 or 5
inches to
clean the
oven
bottom.
Changing the Interior Oven Light (some models)
On some models, the oven light automatically turns on when the door isopened. Some models
have a switch located on the control panel to turn on the light. The oven light is located at the
rearofthe oven.
To replace the oven light:
1. Turn electrical power off at the main source or unplug the range.
2. Replace bulb with a new 40 watt appliance bulb.
3. Turn power back on again at the main source (or plug the range back in).
4. The clock will then need to be reset. To reset, see Setting Oven Controls in this Use &
Care Manual.
Be sure the range is unplugged and all parts are COOL before replacing oven
light. Wear a leather-faced glove for protection against possible broken glass.
Oven
Light
Fig. 1
about 45 ,_
__degrees
OvenDoor
Hinge
Fig. 3
Removing & Replacing the Oven Door
The door is heavy. For safe, temporary storage, lay the door flat with the
inside of the door facing down.
To Remove Oven Door:
1. Open oven door completely (horizontal with floor- See Fig. 1).
2. Remove 2 screws located on the inside of the oven door liner (See A Fig. 2)
3. Insert the 2 screws into the door hinge holes located on the side of the hinge arm,
one into each hinge (See B Fig. 2).
4. Close oven door until the door stops, (Do not force the door to close any further). The
placement of these screws should keep door open in about a 45 degree position.
5. Grasp oven door firmly on both sides and slide door up and off hinges at the same
angle. (See Fig. 3)
6. To clean oven door, follow the instructionsprovided inthe Cleaning Chart at the
beginning of the Care & Cleaning section (See Door Liner).
To Replace Oven Door:
1. Be sure the hinge arms remain at the 45 degree angle position. Be sure the screws
are still locking the hinge arms from moving. If the screws fall out of the hinge holes,
the hinge(s) may snap back against the oven frame and could pinch fingers or chip
the porcelain finish on the oven front frame.
2. Hold door at the sides near the top while resting the lower front of door on your knee.
Insert the door channels at the bottom of door over the door hinges, (See Fig. 3).
3. Allow the door to slide down into the door hinges evenly at the same 45 degree
angle. The hinge arms should be inserted into the bottom corners as far as they can
go.
4. Open door completely (horizontal with floor) and remove both screws from holes in
door hinges.
5. Reinstall the 2 screws into the door liner (See C Fig. 2).
6. If the door is not in alignment with the oven frame, remove door & repeat the above
steps. 10