Croydex PA670322 User manual

S&H 080 R01
1
PA670322
SLIM LINE WALL MOUNTED
SOAP DISPENSER 3 PUMPS
ALL PRODUCT DIMENSIONS DETAILED IN THIS INSTALLATION
AND MAINTENANCE MANUAL ARE APPROXIMATE
ALL ILLUSTRATIONS OF THE PRODUCT ARE FOR REFERENCE
ONLY. COMPONENTS SUPPLIED WITH INDIVIDUAL PRODUCTS
MAY DIFFER
CONTACT DETAILS
Croydex
Central Way
Andover
Hampshire
SP10 5AW
UK
Tel: [phone]
Email: [e-mail]
www.croydex.com

S&H 080 R01
2
SECTION CONTENTS PAGE
1 INTRODUCTION 3
2 PRE-INSTALLATION 3
3 INSTALLATION 4 - 5
4 PRODUCT DIMENSIONS 6`
TABLE OF CONTENTS

S&H 080 R01
3
WALL FIXING PACK
SECTION 2 - PRE-INSTALLATION
x4 wall screws x4 wall plugs
7
mm
TOOLS REQUIRED
PRODUCT FITTING
IMPORTANT!
Before attempting to install this product, ensure that it fits
and will function in the desired location. Refer to the product
dimensions found in SECTION 4.
SECTION 1 - INTRODUCTION
INTRODUCTION
Thank you for purchasing this Croydex product. Please follow
all assembly and product care instructions to ensure that your
product is assembled safely and retains it's high quality finish.
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE
x1
SAFETY & PRODUCT CARE
1. ALWAYS take care when using power tools, particularly if
there is any water in the working area.
2. ALWAYS wear eye protection when using power tools.
3. ALWAYS check for pipes and cables before drilling into
walls.
4. ALWAYS use a ceramic drill bit when drilling into tiled
surfaces.
5. ALWAYS use a drill bit that is suitable for the surface that is
being drilled.
6. The wall plugs supplied are for use on solid walls only. For
cavity walls or plasterboard ALWAYS use specialist fixings
that are suitable for the type of wall construction.
7. DO NOT use abrasive or chemical cleaners as these may
damage the product.
PRODUCT CAPACITY
This product has a total
capacity of 1.35 LITRE
MAX
1.35L

S&H 080 R01
4
SECTION 3 - INSTALLATION
INSTALLING THE WALL BRACKET
1. BEFORE INSTALLING the wall bracket, ensure that the safety
warnings in section 1 are followed.
2. Place the bracket against the wall in the desired position.
Place the spirit level along the top of the bracket, level and mark
the hole centres for drilling. (See Fig. 1)
fig. 1
3. Drill the holes to a depth of 34mm in the marked positions
using a 7mm masonry drill. If the product is being fitted onto a
ceramic tiled wall - a ceramic drill bit should be used.
(See Fig. 2)
fig. 2
fig. 4
5. Insert the wall screws into the wall plugs and tighten with a
cross head screwdriver until the screw heads are approximately
5mm from the wall surface.
(See Fig. 4)
4. Insert the wall plugs flush to the wall surface. If fitting to a
tiled surface the wall plugs should be inserted below the surface
of the tile to avoid cracking.
(See Fig. 3)
fig. 3

S&H 080 R01
5
SECTION 3 - INSTALLATION
6. Slide the wall bracket down onto the screws to lock into place.
(See Fig. 5)
fig. 5
7. Tighten the screws to lock the bracket in place. Do not
overtighten. (See Fig. 6)
fig. 6
8. Slide dispenser unit down onto the wall bracket. Check that
the product is securely fixed to the mounting surface before use
(See Fig. 7)
fig. 7
fig. 8
9. To unlock/lock the
dispenser for refilling. Use the
included key - turn clockwise
to lock and anti-clockwise to
unlock the dispenser.
(See Fig. 8)

S&H 080 R01
6
SECTION 4 - PRODUCT DIMENSIONS
180
33
190
80
SLIM LINE TRIPLE WALL MOUNTED SOAP DISPENSER
All dimensions listed in this fitting book regarding the product
and installation are approximate.