Crye Precision ASR User manual

ASR™LANYARD OPERATOR’S MANUAL
BLC-092

This manual must be carefully read by all persons who have or will have
the
responsibility for using or maintaining this product.
Any warranties made by Crye Precision LLC with respect to this product are voided if the
product is not used and maintained in accordance with the instructions in this
manual.
For any questions relative to the use or repair of this product, please write Crye Precision
LLC or call 1-718-246-3838 during regular business hours.
The following are safety warnings intended to call attention to fundamental performance
limitations and areas of the product where proper usage must be followed. Failure to use and maintain
the product according to the warnings contained herein may result in the product failing to
perform as designed, and/or the persons relying on this product sustaining serious personal injury
and/or death.
•
Refer to the product label and manual for
load rating anduse guidelines.
•The safety belt worn in conjunction with the
lanyard is intended only to prevent the userfrom
reaching a position where a fall can occur.
•The Crye Precision LRB must be worn in
conjunction with the Crye Precision LRB Leg
Loops for mountaineering, rappelling, and fall
arrest.
•The Crye Precision LRB LegLoops must be worn
in conjunction with the Crye Precision LRB.
•Avoid repeated exposure of fall-protection
devices to salt water, solvents, or chemicals. See
care instructions.
•Fall-protection devices that show no signs of
damage must be replaced 5 years from date of
purchase.
•This fall-protection device is notflame resistant.
•Perform periodic inspections of the hardware,
webbing, and stitching of the fall-protection
device. Discontinue use of damaged fall-
protection devices immediately.
•DO NOT machine wash or dry clean the
product. Exposure to detergents, bleach, or
solvents may result in degradation and reduce
the effectiveness of the product.
•Inspect the product for discoloration, cuts,
tears, abrasions or cracks before and after each
use.
•DO NOT alter the product in any way.
•DO NOT expose the product to open flame or
excessive heat.
•All replacement parts must be acquired from
Crye Precision LLC or alicensed distributor.
•The most current version of this manual may be
found at www.cryeprecision.com.
•DO NOT use this product except in itsintended
manner.

EQUIPMENT INFORMATION
INTRODUCTION............................................................... 1
INCLUDED COMPONENTS................................................ 2
CONFIGURING THE ASR™LANYARD
PROPER ATTACHMENTS................................................................. 5
ASR™ADJUSTMENT ...................................................................... 6
RELEASING FROM LRB™................................................. 7
STOWING SAFETY RELEASE PULL.................................... 8
CARE INSTRUCTIONS...................................................................... 11
CONTENTS

1ASR™LANYARD
INTRODUCTION
The Crye Precision ASR™ (ADJUSTABLE SAFETY RESTRAINT) Lanyard is designed to be
used in conjunction with the LRB™ as a travel restraint during helicopter operations.
The ASR™ LANYARD is designed to be quickly and easily adjusted from 18” to 30”.
There are numerous features incorporated into both the LRB™ and ASR™ LANYARD
that are based on user needs and feedback from various SOF groups. The main
features are:
FEATURES
�Ofcially approved for use by USSOCOM
�Carabiner with single-hand operation
�Emergency release from belt under tension
�Length adjustable from 18-30 inches
�Adjuster hardware will not slip under load
�Quickly and easily adjusted while being worn
�Sleeve covers critical stitching for durability
�Meets or exceeds USSOCOM safety lanyard specications
�Made in the US from US materials

2EQUIPMENT INFORMATION
INCLUDED COMPONENTS
ASR LANYARD

CONFIGURING THE ASR™LANYARD

5ASR™LANYARD
PROPER ATTACHMENTS
Ensure the quick release hardware is properly seated and secured
to the LRB™ attachment point.
Ensure the quick release hardware is properly seated and secured
to the LRB™ FLOATING LOOP attachment point.
To attach to LRB™, perform the following:
To attach to LRB™ FLOATING LOOP, perform the following:

6CONFIGURING THE ASR LANYARD
ASR™LANYARD ADJUSTMENT
1To shorten the ASR™LANYARD, pull the free running end away
from the body—excess webbing can be stowed under the elastic
retainers.
2To elongate the ASR™LANYARD, use thumb to pull back on the
adjustment buckle and pull carabiner away from the body.

7ASR™LANYARD
RELEASE FROM LRB™
2
1
Grasp the safety release pull tab and pull it out from the stowage
retainer. Pull safety release pull tab away from the hardware
attachment point to release the snap shackle from the LRB™.
Loop nger or thumb under the safety release pull tab.

8
STOWING SAFETY RELEASE PULL
2
1Fold the safety release tab so that the VELCRO®holds the fold
secure, then insert back into the retainer.
Stow the safety release pull tab into the retainer.
CONFIGURING THE ASR LANYARD

CARE INSTRUCTIONS

11 ASR™LANYARD
CARE INSTRUCTIONS
Care instructions must be read prior to each use.
�You can hand wash your ASR™LANYARD with mild soap and warm water. Never use bleach as that can degrade the materials.
Allow to air dry away from direct sunlight. Do not store damp.

12CARE INSTRUCTIONS
DO NOT
�Machine wash or dry clean.
�Apply iron or any heat to the ASR™LANYARD.
�Expose your ASR™LANYARD to open ame or excessive heat.
�Attempt to modify or repair the ASR™LANYARD in any way.

13 ASR™LANYARD
NOTES

14NOTES

ABOUT US
Crye Precision designs and manufactures
truly innovative equipment for America’s
ghting forces. We are proud and honored
to serve our customers' needs. We spend
as much time as we can with users,
continuously incorporating their experience
and feedback into the gear. We give them
our full support and are indebted to them
for their service and their sacrice. We make
uncompromising gear for uncompromising
individuals. We work hard to provide smart,
high-performance, long-wearing gear for
people who demand the best. We make
all of our gear in America from American
materials. Every item is designed to help
you perform better.
WARRANTY
If a defect in materials or workmanship is
found in any of our products, we will repair
or replace it, free of charge, for the lifetime
of the product. This excludes normal wear
and tear. Be aware that the customer is
responsible for any and all return shipping
charges. This applies to the original purchaser
and is nontransferable.
BODY ARMOR
It is against Federal Law for a person
convicted of a violent felony to purchase
or possess body armor. In addition, various
states also have laws restricting the purchase
or possession of body armor by persons
convicted of certain felonies, other crimes
of violence, or drug crimes. By purchasing
body armor, you acknowledge and certify
that (i) you have no felony convictions, (ii)
you have not been convicted of any other
crime that would restrict your ability to
purchase or possess body armor under any
Federal or State law, (iii) you do not intend
to use the body armor for any criminal
purpose and (iv) you are over 18 years old.
Crye Precision reserves the right, in its sole
discretion, to refuse to sell body armor to any
person. Additionally, the sale of body armor
to residents of Connecticut is restricted to
in-person sales, unless the sale is made to
certain law enforcement or military personnel.
We require that all orders of body armor be
accompanied by a government issued photo
identication.
CONTACT INFO
Crye Precision LLC
Brooklyn Navy Yard
63 Flushing Ave Unit 252
Building 128B
Brooklyn, NY 11205
Phone: [phone]
Fax: [phone]
[email protected]
www.cryeprecision.com
COPYRIGHT
© 2019 Crye Precision LLC. The ‘CP’ logo
are trademarks of Crye Precision LLC.
REV 092217