CST 9448 User manual

MADE IN ITALY

TECHNICAL SPECIFICATIONS
Installation on the wall
Coverage 15 mt, angle 90°
Frequency microwave
10.525 GHz
Alarm technology
DSP(Digital Signal Processing)
Detecting distance
From 3 to 15 mt
Detection areas
8 aeras for each sensor
Installation height
0,8-1,4 m (reccomended 1mt)
Detecting mode
Selectable: AND-OR
Power supply
From 10,5 to 14 VDC
Power consumption
Standby < di 1.5 mA
Max power consumption
12 mA X 4 SEC
Relay contact
NC 100mA
MW range adjustment
By trimmer
Alarm time
1,2 sec
Light indicators
Red IR upper, Red IR lower,
yellow microwave
Detecting speed
from 0.2 to 3.5 m/s
RFI/EMI immunity
3 V/m between 0.1MHz-500MHz
Light immunity
>10000 Lux
Programming
by dip Switch
Operating temperature
From -10°C to +55° C
Protection rating
IP54
DESCRIPTION
Triple Technology Outdoor Detector.
TWIN-X
PIR sensitivity automatic adjustment with
temperature, light and speed changes.
Lower sensor adjustable height in order to
adjust the range and to reduce the false
alarm, with three inclination angles A-B-C

COVERTURE DIAGRAM
Configuration AND position A,B,C
Configuration OR1
Configuration OR 2 position A
Configuration OR 2 position B
Configuration OR 2 position C
Detection plan view.
The microwave detection
covering area is in red.

DETECTION
Configuration AND position A
Configuration AND position B
Cconfiguration AND position C

INSTALLATION METHOD
For a correct working of the Triple Technology Detector you
have to know that:
The microwave is sensitive to any movement, do not point the
sensor towards hedges or tree branches. Adjust the range
rightly.
Metal surfaces reflect the microwave modifying the range
The two passive infrared sensors are sensitive to rapid
temperature changes. Avoid to direct the sensor towards the
sun (point the sensor directly to the sun). In presence of animals
adjust the detection angle righly.
The detector has a regulation time of around 1 minute at the first
functioning.
Terminal block
.
DETECTING OPTIONS
From the factory the
programming DIP are set like in
the figure.
DIP1
LED
With this DIP are activates or de-activates the LED indicators
with DIP1=ON alarm conditions are activates,
with DIP1=OFF alarm conditions are de-activates.

DIP 2
ANTI MASK
Setting the DIP 2 Off we exclude anti-masking.
Set dip 2 in ON you turn on the front masking infrared active
If the dark field detection sensor and the dip 2 is ON, in a maximum
time of 10 seconds generates a tamper alarm (the output-mask open)
and remains in alarm as long as it remains the cause .
DIP3
AND
This function is activated setting DIP 3 in Off position. In this
configuration, when the two infrared sensors and the microwave
sensor detect a movement, the detector, will produce an alarm. This
mode is recommended in external environments with unstable
elements that could be produce false alarms.
OR
This mode is activated setting DIP 3 in Off position. In this
configuration, when one of the two infrared sensors and the
microwave sensor detect a movement, the detector will produce an
alarm. It is recommended in completely external environments and in
presence of small animals.
With this mode every small movement is detected.
DIP 4
MICROWAVE DE-ACTIVATION
DIP 4 in OFF. Microwave active.
DIP 4 in ON . Microwave de-activate.
This mode refers to the microwave alarm detection.
In particularly narrow environments ( such as garage passages,
gardens pedestrian areas) it is reccommended setting DIP 4 in On
position in order to have the infrared sensors detection only. If you
use this mode, you will always set DIP 3 in Off position (AND mode).
Let DIP 5 in ON position.

WORKING/OPERATING TEST
Setting Dip 1 in ON position
Check and adjust the covering area (see the previuos diagramm)
Move into the protecting area and check the specific indicators (LED)
switching on.
Considering that the two infrared sensors are sensitive to the across and
not to the approach.
If the detection do not meet the own needs you will adjust the microwave
range by the trimmer ( to put up turning in an anticlockwise direction and
to put down turning in an clockwise direction) or you will adjust the sensor
inclination angle. N.B. When the microwave detect a movement too, the
detector will produce an alarm, the microwave is always turn off, it is
activated with AND mode if both the two infrared sensors detect an alarm.
With OR mode if one of the two infrared sensors detects an alarm.
INSTALLATION TIPS

Caution /Take note
In precence of hedges or bushes, cover the beams infrared lens corresponding to the plants
like in the figure.