CTC Union GW-732FW User manual

GW-732FW
Gigabit Fiber IAD with IEEE 802.11ac WiFi

ii
LEGAL
The information in this publication has been carefully checked and is believed to be entirely accurate at the
time of publication. Our company assumes no responsibility, however, for possible errors or omissions, or
for any consequences resulting from the use of the information contained herein. Our company reserves
the right to make changes in its products or product specifications with the intent to improve function or
design at any time and without notice and is not required to update this documentation to reflect such
changes.
Our company makes no warranty, representation, or guarantee regarding the suitability of its products for
any particular purpose, nor do we assume any liability arising out of the application or use of any product
and specifically disclaims any and all liability, including without limitation any consequential or incidental
damages.
Our products are not designed, intended, or authorized for use in systems or applications intended to
support or sustain life, or for any other application in which the failure of the product could create a
situation where personal injury or death may occur. Should the Buyer purchase or use our product for any
such unintended or unauthorized application, the Buyer shall indemnify and hold our company and its
officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages,
expenses, and reasonable attorney fees arising out of, either directly or indirectly, any claim of personal
injury or death that may be associated with such unintended or unauthorized use, even if such claim
alleges that our company was negligent regarding the design or manufacture of said product.
Federal Communications Commission (FCC) NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
�Reorient of relocate the receiving antenna.
�Increase the separation between the equipment and receiver.
�Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
�Consult the dealer or an experienced radio / TV technician for help.
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with
the unit to insure compliance. This statement can be deleted if unit was not tested with shielded cables.
The manufacture is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user's authority to operate the
equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
Change or modifications that are not expressly approved by the manufacturer could void the user＇s
authority to operate the equipment.
CISPR PUB.22 Class B COMPLIANCE:
This device complies with EMC directive of the European Community and meets or exceeds the following
technical standard. EN 55022 - Limits and Methods of Measurement of Radio Interference Characteristics
of Information Technology Equipment. This device complies with CISPR Class B.
WARNING:
This is a Class B product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
CE NOTICE
Marking by the symbol CE indicates compliance of this equipment to the EMC directive of the European
Community. Such marking is indicative that this equipment meets or exceeds the following technical
standards: EN 55022:2006+A1:2007, Class A, EN55024:2010.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.

iii
Gigabit Ethernet Fiber IAD Gateway with IEEE 802.11ac WiFi
User Manual
Version 0.9 March 2015
2015 All Rights Reserved
The contents of this document are subject to change without any prior notice.

iv
Contents
1. Introduction ........................................................................................................................................................1
1-1 Product Overview .......................................................................................................................................1
1-2 Hardware Description.................................................................................................................................2
2. VoIP Wireless Gateway Web Configuration.....................................................................................................4
2-1 Status..........................................................................................................................................................5
2-1-1 Current Status ..................................................................................................................................5
2-1-2 RTP Packet Summary......................................................................................................................5
2-1-3 System Information..........................................................................................................................6
2-1-4 Routing Table ...................................................................................................................................7
2-1-5 LAN Client........................................................................................................................................8
2-2 General Settings.........................................................................................................................................9
2-2-1 Network operation mode..................................................................................................................9
2-2-2 Standard WAN..................................................................................................................................9
2-2-3 Standard LAN.................................................................................................................................13
2-2-4 Multiservice WAN...........................................................................................................................14
2-2-5 Multiservice LAN ............................................................................................................................14
2-2-6 SIP..................................................................................................................................................18
2-2-7 SIP Advanced.................................................................................................................................23
2-2-8 Caller ID .........................................................................................................................................27
2-2-9 Hot Line..........................................................................................................................................28
2-2-10 Line settings.................................................................................................................................29
2-2-11 FAX...............................................................................................................................................32
2-2-12 Calling Features...........................................................................................................................34
2-2-13 Phone Book..................................................................................................................................36
2-2-14 CDR Settings ...............................................................................................................................36
2-3 Wireless Settings......................................................................................................................................38
2-3-1 Basic Settings ................................................................................................................................38
2-3-2 Advanced Settings .........................................................................................................................40
2-3-3 Security Settings ............................................................................................................................41
2-3-4 Access Control ...............................................................................................................................44
2-3-5 WPS...............................................................................................................................................45
2-4 Advanced Settings....................................................................................................................................49
2-4-1 Codec setting .................................................................................................................................49
2-4-2 Digit Map........................................................................................................................................50
2-4-3 DTMF & PULSE.............................................................................................................................54
2-4-4 CPT / Cadence...............................................................................................................................55
2-4-5 TR069.............................................................................................................................................56
2-4-6 Caller Filter.....................................................................................................................................58
2-4-7 Static Route....................................................................................................................................59
2-4-8 DDNS.............................................................................................................................................60
2-4-9 NAT Traversal.................................................................................................................................61
2-4-10 DoS Protection Settings...............................................................................................................62
2-4-11 DMZ / ALG....................................................................................................................................62
2-4-12 IP Filtering....................................................................................................................................63
2-4-13 Port Filtering.................................................................................................................................64
2-4-14 MAC Filtering ...............................................................................................................................64
2-4-15 Virtual Server................................................................................................................................65
2-4-16 UPnP............................................................................................................................................65
2-5 Tools.........................................................................................................................................................66
2-5-1 Ping Test.........................................................................................................................................66
2-5-2 STUN Inquiry..................................................................................................................................67
2-6 System Settings........................................................................................................................................68
2-6-1 NTP................................................................................................................................................68
2-6-2 Language .......................................................................................................................................68
2-6-3 Login Account.................................................................................................................................69
2-6-4 Backup / Restore............................................................................................................................70
2-6-5 System Log ....................................................................................................................................71
2-6-6 Save / Restart.................................................................................................................................71
2-6-7 Software Upgrade ..........................................................................................................................72
2-6-8 Logout ............................................................................................................................................72

v
3. Configuring the VoIP Gateway through IVR..................................................................................................73
3-1 IVR (Interactive Voice Response) ............................................................................................................73
3-1-1 IVR Functions Table:......................................................................................................................74
3-2 IP Configuration Settings..........................................................................................................................75
3-2-1 Character Conversion Table:..........................................................................................................76
4. Dialing Principles.............................................................................................................................................77

Dual Band Wireless VoIP Gateway User’s Manual
1
1. Introduction
1-1 Product Overview
The VoIP Gateway is designed to carry both voice and facsimile over the IP network. It uses the industry standard
SIP call control protocol so as to be compatible with free registration services or VoIP service providers’ systems.
As a standard user agent, it is compatible with all common Soft Switch and SIP proxy servers. While running
optional server software, the VoIP Gateway can be configured to establish a private VoIP network over the
Internet without a third-party SIP Proxy Server.
The VoIP Gateway can be seamlessly integrated into an existing network by connecting to a phone set and fax
machine. With only a broadband connection such as an ADSL bridge/router, a Cable Modem or a leased-line
router, the VoIP Gateway allows you to use voice and fax services over IP in order to reduce the cost of all long
distance calls.
The VoIP Gateway can be configured a fixed IP address or it can have one dynamically assigned by DHCP or
PPPoE. It adopts either the G.711, G.726, G.729A or G.723.1 voice compression format to save network
bandwidth while providing real-time, toll quality voice transmission and reception.

Dual Band Wireless VoIP Gateway User’s Manual
2
1-2 Hardware Description
Front Pannel
Indicators
Power: Power LED. A steady light indicates a proper connection to a power source.
Prov./Alm.: A blinking light indicates the VoIP Gateway can not register with SIP Server or can not get the
IP address. A blinking light also indicates the VoIP Gateway is attempting to connect with the Provisioning
server. Once the service connects, the LED will turn off. The LED will light solid red if the self-test or boot-up
fails.
Reg.: The Register LED will turn on and continuously working when VoIP Gateway is connected to a VoIP
service provider. The LED will flash if not connected to a service provider.
Phone1~2: This LED displays the VoIP status and Hook/Ringing activity on the phone port that is used to
connect your normal telephone(s). If a phone connected to a phone port is off the hook or in use, this LED
will light solid. When a phone is ringing, the indicator will blink.
WAN: When a connection is established the LED will light up solid. The LED will blink to indicate activity. If
the LED does not light up when a cable is connected, verify the cable connections and make sure your
devices are powered on.
WLAN 2.4G/5G: A steady light indicates a wireless connection. A blinking light indicates that the VoIP
Gateway is receiving/transmitting from/to the wireless network.
LAN1~4 : When a connection is established the LED (bottom) will light up solid on the appropriate port. The
LEDs will blink to indicate activity. If the LED does not light up when a cable is connected, verify the cable
connections and make sure your devices are powered on.
USB1~2 : This indicates that VoIP Gateway detects a supported 3G modem dungle or a USB device.
WPS: Flashing in blue as wireless router processing WPS-PBC wireless connecting progress.

Dual Band Wireless VoIP Gateway User’s Manual
3
Rear Panel
1. WLAN Switch: Switch it to power on/off wireless feature.
2. USB 1~2: Connect to a 3G USB dongle or a printer.
3. LAN: 10/100/1000M Gigabit Ethernet. Connect to your Ethernet enabled computers using Ethernet cabling.
4. WAN: 10/100/1000M Gigabit Ethernet. Connect to your broadband modem using an Ethernet cable.
5. Optical WAN: Insert 155M/1.25G fiber optic SFP module and connect to a switch or router.
Note: VoIP Gateway allows alternative Copper or Optical WAN at the same time.
1. If you connect Copper WAN at first that Optical WAN will not take active unless remove
RJ45 cable from Copper WAN port.
2. If you connect Optical WAN at first that Copper WAN will not take active unless remove fiber
from Optical WAN port.
6. Phone Port (1-2): Connect to your phones using standard phone cabling (RJ-11).
7. Power Receptor: Receptor for the provided power adapter.
8. Power Switch: Press down to turn-on VoIP Wireless Router.
WARNING: DO NOT (1) connect the phone ports to each other (FXS to FXS) or (2) connect any
phone port directly to a PSTN line (FXS to PSTN) or to an internal PBX line (FXS to PBX extension).
(3) Stacking is forbidden. Doing so may damage your VoIP Gateway.
WPS: WPS button for wireless WPS-PBC setup method.
Antenna: Connect to a wireless network.
Reset button: Use to restore factory default settings.
Note: Use Reset Button to restore factory default settings:
1. Press and hold the reset button for 5 seconds.
2. As Alarm indicator is blinking, please release the reset button. Factory settings will be restored.
POWER Connects to
the power adapter
(comes with the
gateway)
FXS ports 1 ~ 6
(telephone connectors)
Connects to phone sets
FXO ports 7,8
(PSTN line connectors)
Connects to PSTN lines
LAN ports 1 ~ 4
(built-in Ethernet switch)
Connect LAN hosts here
to share WAN
connection.
IP sharing features
enabled
RESET
To reset the gateway
or to restore
factory settings
POWER
Connects to the power
adapter (comes with
the gateway)
WAN port
Connects to broadband
Networks such as
ADSL,
Cable Modem or Router
RESET
To reset the gateway
P2-P4

Dual Band Wireless VoIP Gateway User’s Manual
4
2. VoIP Wireless Gateway Web Configuration
The VoIP Gateway allows users to configure its settings using a web interface (Web UI). You can access the
Configuration Menu by opening a web-browser (e.g., Internet Explorer or Netscape Navigator) and entering the
factory default LAN IP address: 192.168.8.254.
Instructions
Open a Web-Browser (e.g., Explorer, Navigator, Opera, FireFox).
Enter the LAN port IP address in the address filed and press Enter. The default LAN port IP address is:
192.168.8.254.
The log-in screen below will appear after you connect. (The factory default settings for Username and
Password are left blank).
The VoIP Gateway does not allow multiple people to configure the VoIP Gateway simultaneously. Please
remember to logout or restart the system if you are not using the web configuration function.

Dual Band Wireless VoIP Gateway User’s Manual
5
2-1 Status
2-1-1 Current Status
Status →Current Status
For Port Status, it includes if each port registers to Proxy successfully, the last dialed number, how many
calls each port has made since the VoIP Gateway starts, etc.
For Server Registration Status, it shows the registration status of DDNS, STUN and FXS Represent
Number.
2-1-2 RTP Packet Summary
Status →RTP Packet Summary
Display the information of the last call made. Press Refresh button to get the latest RTP Packet Summary.

Dual Band Wireless VoIP Gateway User’s Manual
6
2-1-3 System Information
Status →System Information

Dual Band Wireless VoIP Gateway User’s Manual
7
For WAN Port Information, it shows IP address, subnet mask, default gateway and DNS server. If you use
PPPoE to obtain IP, you will know if the IP is obtained through this method. If IP address, subnet mask,
default gateway is blank, it means that the VoIP Gateway does not obtain IP.
For LAN Port Information, it shows LAN port IP, subnet mask, and the status of DHCP server.
For Hardware, it shows the hardware platform and driver version.
2-1-4 Routing Table
Status →Routing Table
It displays routing table of VoIP Gateway.

Dual Band Wireless VoIP Gateway User’s Manual
8
2-1-5 LAN Client
The DHCP Clients table displayed LAN device that has already been assigned an address from VoIP
Gateway. You can check if the DHCP client has obtain an IP address.
Status →LAN Client

Dual Band Wireless VoIP Gateway User’s Manual
9
2-2 General Settings
2-2-1 Network operation mode
IAD Gateway provides 2 network operation mode: Standard mode and Multiservice mode.
2-2-2 Standard WAN
WAN (Wide Area Network) Settings are used to connect to your ISP (Internet Service Provider). The WAN
settings are provided to you by your ISP and oftentimes referred to as "public settings". Please select the
appropriate option for your specific ISP.
IP Configuration (Setting WAN Port)
There are four methods of obtaining a WAN port IP address:
1. Static IP
2. DHCP
3. PPPoE
4. PPTP
5. USB 3G
Methods for using DHCP and PPPoE for obtaining an IP address may vary. If you are not familiar with
creating a network connection, please contact your local ISP.
After selecting the suitable option, click Accept at the bottom of the screen to save the settings.
You need to save the changes and restart the VoIP Gateway to make the changes active. Enter “System
Settings-> Save/ Restart”page then Save and Restart. Wait for about 50 seconds before the VoIP
Gateway obtaining an IP address by the method you selected.
Note: When the system has obtained a new IP address, and you are using a WAN port to enter the Web
Configuration Screen, the new IP address has to be used before you can get connected to the VoIP
Gateway. The same principle applies to the next two settings.

Dual Band Wireless VoIP Gateway User’s Manual
10
General Settings →WAN
DHCP:Select this option if your ISP (Internet Service Provider) provides you an IP address automatically.
Cable modem providers typically use dynamic assignment of IP Address. The Host Name field is optional
but may be required by some Internet Service Providers.
General Settings →WAN
Static IP: Select this option if your ISP (Internet Service Provider) provides you a Static IP address. Enter
the IP address, Subnet Mask and Default Gateway IP.

Dual Band Wireless VoIP Gateway User’s Manual
11
General Settings →WAN
PPPoE: Select this option if your ISP requires you to use a PPPoE (Point-to-Point Protocol over Ethernet)
connection. Enter the PPPoE Account, PPPoE Password and re-enter Password to confirm.
General Settings →WAN
PPTP: Point-to-Point Tunneling Protocol (PPTP) is a WAN connection. Enter the IP Address, Subnet
mask, PPTP Server, PPTP ID and Password.

Dual Band Wireless VoIP Gateway User’s Manual
12
General Settings →WAN
USB 3G: 3G/3.5G WISP. Enter Username, Password, Dial Number and APN to connect to Internet via
3G/3.5G WISP. Users could also select a configured WISP from the list and the gateway will fill necessary
parameter automatically.
General Settings →WAN
VoIP Connection Interface: Select a WAN interface for VoIP traffic bound with as WAN 2 is enabled.
General Settings →WAN
WAN Access: Check the box to enable access protocol of WAN .
General Settings →WAN
Bridge mode: check the box to set the Gateway serving as a Bridge between WAN port and LAN port
without NAT.

Dual Band Wireless VoIP Gateway User’s Manual
13
2-2-3 Standard LAN
General Settings →LAN
LAN IP / LAN default Gateway: Enter the LAN IP address of the VoIP Gateway. It is also the default
gateway for DHCP clients.
Subnet Make: Enter the subnet mask for DHCP clients.
Enable DHCP Server: This variable is to assign the IP address for the devices connected to LAN port of
the VoIP Gateway.
IP Pool Starting Address: Enter the starting IP address for the DHCP server's IP assignment.
IP Pool Ending Address: Enter the ending IP address for the DHCP server's IP assignment.
Lease Time: Enter the length of time for the IP lease.
General Settings →LAN
LAN Access: Check the box to enable access protocol of LAN.

Dual Band Wireless VoIP Gateway User’s Manual
14
2-2-4 Multiservice WAN
Multiservice WAN List shows the multi-WAN settings.
2-2-5 Multiservice LAN
Multiservice LAN List shows the multi-LAN settings.

Dual Band Wireless VoIP Gateway User’s Manual
15
Below provide example for how to configure for Multiservice WAN/LAN
Example 1:
4 VLANs for Internet Data, VoIP, IPTV and management VLAN. And IPTV STB connected at NAT-LAN port
WAN setting:
Step1: Select Network Operation Mode to “Multiservice Mode”
Step2: Enable Virtual WAN and Configure 4VLANs for Internet Data, VoIP, IPTV and Management
VLAN