Ctronics CT-WDB02 User manual

........................................
....................................
......................................
............................................
01 ~ 11
12 ~ 23
24 ~ 35
36 ~ 47
English
Deutsche
Français
Italia

Quick Start Guide
English

Please consult below checklist for all the components.
1. what’s in the box
2. meet the doorbell
User GuideUSB Cable
Video Doorbell Adhesive Tape
3. Meet the chime
Speakers
Reset
2
1LED Indicator
USB Port (Type-A/M)
3
4
1
3
2
4
Indoor Chime Screw & Tools
- 1 -
2MP camera
Motion sensor
Speakers
Doorbell button
LED indicator
Charging indicator
Micro-USB port
Reset hole
Security screw hole
Microphone
Power contacts
Hardwire terminals
Micro-SD card slot
18650 Battery pack
Security screw
Mounting screw holes
3
2
1
4
6
5
8
7
10
9
12
11
13
15
16
14
12
11
13 14
2 1
4
5
10
6
7
8
9
3
1615

4. Battery installation
The batteries are pre-installed in the doorbell, with an isolating film inserted
in the positive poles. Please remove the film and insert the battery pack
back to compartment, with positive poles upwards!
NOTE:
Improper battery installation will cause damage to the internal components
and may result in serious injury.
The batteries inside the doorbell are not fully charged in accordance with
transportation safety regulations.
Please charge the batteries with a USB compatible wall charger (not included)
and the provided USB cable for about 8~10 hours prior to installation.
5. Battery charging
- 2 -
7. wi-fi set up
Before you start the Wi-Fi configuration, please note below:
1). The doorbell works with 2.4 GHz Wi-Fi, but not with 5 GHz Wi-Fi.
2). Avoid using special characters or symbols like )(@~!#$%^&*..., either in your Wi-Fi name or password.
3). Perform the configuration near your Wi-Fi router.
6. Download the app
Download and install the 'CloudEdge' App from Google Play
TM
or the
App Store
TM
. The App is also available by scanning the QR codes on
the right, using your QR code scanner on your smart phone.
NOTE:
Google Play
TM
is a trademark of Google Inc.
App Store
TM
is a service mark of Apple Inc.
Launch the ‘CloudEdge’ App and register an account with your mobile phone numer or email ID. Start the
Wi-Fi configuration, following the in-App instructions or refering to the following guiding steps.
Android
iOS
CloudEdge
isolating film

9:55
Devices Messages Me
Tap + to add a new device
Devices
 Using the supplied reset pin, reset the
device(please consult the user manual for more on
this)
 Wait for the LED indicator to flash RED
 Tap Next
Please reset the device
Install Doorbell
Next
9:55
Install Doorbell
Press the [Bell] button, and tap Next
Help
Next
9:55
Please follow the instruction manual to
power the device
Please stay near your router for the best signal
Install Doorbell
Next
9:55
Camera
Battery Camera Floodlight Camera
Network Video
Recorder
Doorbell
1. Tap “+” to add device 2. Select Doorbell 3. check power status 4. Activate the doorbell 5. Reset device
9:55
Devices Messages Me
Devices
056853326
Select your Wi-Fi network
Change WiFi
Hide Password
Home
Password123
(Please select a 2.4G network, this device will not
work with 5G Wi-Fi networks)
Wi-Fi Setup
Next
9:55
Scan QR Code
Scan the QR code below with the
device at a distance of 5-8 inches.
A tone will be heard when
successfully scanned.
Help Next
9:55
Please stay near your router for the
best signal
Device Found!
Connecting device to network...
Registering device...
12%
connecting...
Connect Network
Operation
Next
9:55
Please remove all film from the lens. Tap
Next to show a QR code, and let your
device scan the code. Keep your phone 5-8
inches from the lens.
15~25cm
5~8 in
6. Input Wi-Fi password 7. Prepare Code Scanning 8.Generate QR Code 9. Wait for connection 10. Adding device complete
Guiding steps:
- 3 -
8. run a test
After setup, tap on the live view window in the App for a test. Then take your doorbell outside to the installation
spot and run a test there. Make sure the installation spot is covered by strong 2.4 GHz Wi-Fi signal.
Note:
If the video quality from the doorbell outside is not as good as it was indoors, you may need to move your
router closer to your installation spot, or invest in an Wi-Fi extender.

- 4 -
9. Live viewing
3
6
4
1
7
2
5
Quit live viewing
Setting menu
Battery status
Volume on/off
HD/SD switch
Full screen display
Stream bit rate
9
10
13
8
11
14
12
Wi-Fi signal status
Screenshot button
Speak to the scene
Record on the phone
Body detection on/off
Notification history
Cloud storage service
Note:
Live viewing will not trigger device recording.
10. Playback
If the Micro-SD card is properly installed, you can playback the video clips taken after detected motions or
visitor calls. (Live viewing will not trigger device recording). You can also back up video clips to the cloud,
only if you have activated the cloud storage service (Charge after a 7-Days-Free trial).
HD
Live view interface
Playback interface Cloud storage interface
10:58:06
10:57 10:57:30 10:58 10:58:30 10:59 10:59:
Calendar
Alarm
10:58:06
10:57 10:57:30 10:58 10:58:30 10:59 10:59:
Calendar
Alarm
Nov 2019
SUN MON TUE WED THU FRI SAT
27 28 29 30 31 1 2
10 11 12 13 14 15 16
17 18 19 23 21 23
24 25 26 27 28 29 30
3 4 5 6 7 8 9
3 4 5 6 71 2
22
10:58:06
10:57 10:57:30 10:58 10:58:30 10:59 10:59:
Visitor Message 09:29:30
Visitor Message 10:10:02
Visitor Message 10:56:56
Moton Detection 10:58:45
Motion Detection10:59:21
Visitor Message 13:09:30
Motion Detection 14:39:51
10:57 10:57:30 10:58 10:58:30 10:59 10:59:
Cloud storage is not active
Activate
Search video clips by date Search video clips by events
10:58:06
10:57 10:57:30 10:58 10:58:30 10:59 10:59:
Visitor Message 09:29:30
Visitor Message 10:10:02
Visitor Message 10:56:56
Moton Detection 10:58:45
Motion Detection10:59:21
Visitor Message 13:09:30
Motion Detection 14:39:51
Timeline
zoom in/
zoom out

- 5 -
11. leave Voice messages
Maximum 3 voice messages (Max. 10 seconds each) can be pre-recorded into the doorbell, which enables
you to quickly respond to your visitors when you are not convenient to answer the doorbell call.
Steps: Setting --> Basic function --> Host Leaves Message --> Press and hold this icon to record
voice messages --> Push doorbell button--> Play the selected voice message in reply to doorbell call
Steps: Settings>>Device Share>>Tap on “Add ”>>Tap on “Account”>>Type in account ID>>Confirm Sharing.
12. share Your device
Device Share
9:55
1372896****
Lil
Shared
Requesting
mophie2019**@gmail.com
Mophie
Add
Delete Device
Device Share
Receive Notifications
Device Information
Basic Function
Alarm Setting
Device Version
SD Card
Cloud Server
Settings
1
Device Share
9:55
Add
2
Device Share
Recent contacts
Scan QR Code Account
3
Device Share
9:55
Search
Please enter your family’s account
mophie2019**@gmail.com|
4
5
sharing by account searching
057394082
You have a visitor
Delete Device
Device Share
Receive Notifications
Device Information
Basic Function
Alarm Setting
Device Version
SD Card
Cloud Server
Settings
1
Night Vision
Wireless Chime
Power Management
Automatic
BasicFunction
Host Leaves Message
2
Voice Mail
My voice mail
voice msg 1
voice msg 2
Hold the button to record voice mail
0:04
3
Tap Here
057394082
You have a visitor
Send voice mail
Voice Msg 1
Voice Msg 2
Voice Msg 3
Cancel
My voice mail
How to share devices?

- 6 -
(not included)
(not included)
1. Powered by DC5V phone charger. 2. Powered by PC USB Port.
13. connect the chime
The chime can be powered by an USB compatible phone charger (DC5V 1A). You can also plug the chime
to the USB port on your PC/notebook to supply power.
Sharing by QR code scanning
The new users can show their QR codes to the administrator, and share device by QR Code scanning.
Find your QR code: Run CloudEdge App >> Tap on “ ” >> “User Name” >> “My QR Code”
>> Let the administrator scan your QR Code
NOTE:
1. Guide your family members to download and
install the CloudEdge App, and register an account
prior to device-sharing.
2. There is no limitation on the number of users
sharing one device.
3. Only the adminstrator got access to the setting
menu. Other users can only live view & playback.
4. All users will receive doorbell calls and alarm
notifications.
5. Many users can access to the doorbell simul
-tanously, to live view or playback.
My QR Code
User Name
1882020****
Scan the QRCode to share camera with me
9:55
Devices
User Name
1882020****
In-App Alert Sound
Pictures & Videos
Device Share
FAQ
Feedback
Online Help
More
1
2
My information
Account
Edit Nickname
Profile Photo
Reset Password
My QR Code
Your Region
Log Out
User Name
1882020* * * *
Region
3
1 ). supply power to the chime

- 7 -
4). chime settings
2). Click reset button
3). Press the doorbell button
Reset Button LED Indicator
Click the RESET button on the wireless chime only
once, and you will see the LED indicator flashing
blue, indicating the chime is in pairing mode.
You can enter into the chime setting page following below setting steps, so as to mute the Chime
Reminder, select ringtones, adjust chime volume or unbind the connection with doorbell.
Press the doorbell button,
and the Chime will sound to react. Pairing
succeeds, and the indicator on the chime will
be in solid blue.
Night Vision
Wireless Chime
Power Management
Automatic
BasicFunction
Host Leaves Message
Step.2 Step.3Step.1 Step.4
Wireless Chime
Middle
Chime Pairing
One-button untie
Chime Reminder
Delete Device
Device Share
Device Information
Basic Function
Alarm Setting
Device Version
SD Card
Cloud Storage Service
Settings
Receive Notifications
NOTE:
1. Your doorbell communicates with the chime via Radio Frequency, but not WiFi. You can even do the
pairing prior to doorbell configuration.
2. You can add many chimes to one doorbell, and vice versa.
3. Press and hold RESET button on the chime for 5 seconds till the indicator flashes blue 3 times, and
you can also release the connection between the chime and its connected doorbell.
View operation video?
Ring Volume

(Example)
The Smiths
Your doorbell has 166-degree view angle and 120-degree
human detection range.
It is suggested to mount your doorbell at least 5 feet (160 cm)
above the ground for the best angle of view and motion
detection performance.
The doorbell works with both 12V ~ 24V AC and 12V DC hardwire power source. Either wire can be connected
to either terminal. The cable order doesn't matter.
14. Installation
Select location
Hardwire your doorbell (Optional)
- 8 -
5 feet
160cm
166°
1. (Optional) Shut off power at the breaker,
remove the old doorbell from the wall and
disconnect the wires.
2. Connect the wires to the screw terminals
on your mounting bracket. Either wire can be
connected to either terminal.
6. Mount the doorbell to the bracket, and
secure it with the provided star-shape
security screw and screw driver. All set!
3. (Optional) The nameplate holder can be
mounted on the top rear/ bottom rear of the
bracket, prior to bracket installation.
4. Drive the screws into the anchors, or
directly into your wall untill the bracket
is tightly fastened on your wall.
5. (Optional) You can also use the provided
double-sided tape instead of screws to fix
the wall mount on flat surface.
Double-sided
adhesive tape

(Example)
The Smiths
Go wireless installation
- 9 -
Note:
1. When hardwire your doorbell, please operate under the guide of the professionals.
2. The doorbell works with 12V - 24V AC and 12V DC power source. And either cable can connect to either
terminal. The connecting order doesn’t matter.
3. If your doorbell is powered solely on batteries, you may need to charge your doorbell once in a while.
Lab-tested battery life: 12 month standby, 6 month regular using(activate 20 time per day. (The actual
battery life may be different due to different activation freqency).
3. (Optional) The nameplate holder can be
mounted on the top rear/ bottom rear of the
bracket, prior to bracket installation.
1. Dismount the bracket by pushing from
the back of your doorbell. Please remove
the insulation film in the battery cell.
4. Mount your doorbell to the fixed bracket.
Make sure it reaches the bottom where you
can hear a click.
5. Secure your doorbell with the provided
star-shape security screw and screw driver.
6. All set, congratulations!
Now you can press the doorbell button
to try it out.
2. Bracket installation: mount the bracket on
the wall with screws & anchors or the double
-sided adhesive tape.
The Smiths

15. Specification
Video doorbell
Power source
Power port
Consumption
Ringtones
Volume
Volume control
Connection type
Frequency
Place of use
DC 5V 1A
USB (Type-A)
0.2W
4 ringtongs optional
Max 100dB
Low(mute), middle, high
Radio frequency
indoor
Bleu clignotant: mode d'appairage
Bleu fixe: mise sous tension /
association réussie
Flash bleu deux fois: réinitialisation aux
paramètres d'usine
433MHz-868MHz
LED
Working Temp.
Humidity
Dimension(mm)
Weight (g)
-30℃ ~ 70℃
< 90%, no condensation
33
Ø60 × 24
General
Indoor Chime
Storage Type
Cloud storage
Recording
Storage
Video & Audio
Image Sensor
OS
Resolution
Stream
Infrared LED
Lense
Angle of view
Min. illumin.
WDR
Audio
1/2.7” CMOS (2.0MP)
Lite-OS
1920 × 1080 px
HD/SD dual stream
High power IR LED with ICR
1.7mm/F2.0
166°
Digital WDR
2-way audio with noise cancellation
Color: 0.01 Lux; B&W: 0.001Lux
Network
Wifi Frequency
Standards
Live View Speed
Micro SD Card (Max 128G)
Support
Triggered by PIR motion sensor
2.4 GHz ~ 2.4835 GHz
IEEE 802.11 b/g/n
Within 3 ~ 4 Sec
Software
App Name
OS
Remote View
Notification
CloudEdge
iOS, Android
Within 2~4 sec
Push notification within 2~4 sec
General
Lithium 18650 Battery (3.5V, 3350mAh ) × 2/
AC 12V - 24V hardwire power/
DC 12V hardwire power
300μA
250mA
4 ~ 6 Months
2 ~ 3 Months (20 times wake up per day)
DC5V 1A ~ 2A (Micro USB Port)
61× 41 × 144
145 + 90 (Battery weight)
OTA (Over-The-Air)
-20℃ ~ 50℃; <90% (No condensation)
Power Source
Standby Current
Working Current
Standby Time
Working Time
Battery Charging
Firmware Upgrade
Dimension (mm)
Weight (g)
Working Temp.
& Humidity
- 10 -

16. Trouble shooting
Q1: Why I failed to set up Wi-Fi for the doorbell?
A1: .Device works with 2.4GHz Wi-Fi only, but not support 5GHz Wi-Fi. .Wi-Fi network is not good, try to keep the
camera near the Wi-Fi router when setting up. .The Wi-Fi password is wrong. Please check if there are special
characters in the password, or the network is specially encrypted.
Q2: How do I know if I have 2.4G or 5G wifi?
A2: Please check the user manual of your Router or call the network operator for help.
Q3: It has to be on same WiFi to see the camera, or is it over internet from anywhere?
A3: You can view the camera from anywhere, if your camera is well connected to the internet.
Q4: Do any of the recordings get saved to the cloud? Or is it mainly saved in the built-in SD card?
A4: It supports SD card recording as well as cloud storage. You can activate the cloud storage service in App.
Q5: What happens when the SD is full?
A5: When the memory card is full, the camera automatically erase the oldest footage.
Q6: Does it work with Google Home or Alexa?
A6: Sorry, this model does not support Google Home or Alexa.
Q7: Why does it lose connection to wifi?
A7: Please check the network connection of your phone and the Wi-Fi router. If the network signal is not strong, you
may need to move your router closer to the device, or invest in an extender.
Q8: Can the motion detection be disabled?
A8: Yes, sure. Recording is triggered by detected motions. You can set up the sensitivity or disable motion detection in
the setting menu.
Q9: Do we get charger for the batteries?
A9: Battery charger is not included. Please charge the batteries with a USB compatible charger(DC5V 1A~2A) for about
8-10 hours.
Q10: Can we have 2 or more doorbells at the same residence?
A10: Yes, you can add more than one device at the same residence.
- 11 -

Schnellstartanleitung
Deutsche
* Vielen Dank für den Kauf und die Nutzung unseres Produkts.itung vor der Verwendung und bewahren Sie sie zum
späteren Nachschlagen auf.
* Der Inhalt des Handbuchs kann in Übereinstimmung mit unserer Politik der kontinuierlichen Produktverbesserung
ohne Vorankündigung geändert we Bitte lesen Sie diese Schnellstartanlerden.

Bitte konsultieren Sie die untenstehende Checkliste für alle Komponenten.
1. Paktinhalt
2. Die Türklingel kennenlernen
Benutzerhandbuch
USB-KabelVideo Türklingel
Klebeband
3. Die Klingel kennenlernen
Lautsprecher
Zurücksetzen
2
1LED-Anzeige
USB-Anschluss (Type-A/M)
3
4
1
3
2
4
Indoor Glockenspiel Schrauben und
Werkzeuge
- 13 -
2MP Kamera
Bewegungsmelder
Lautsprecher
Türklingel-Taste
LED-Anzeige
Ladeanzeige
Mikro-USB-Anschluss
Zurücksetzen-Loch
Sicherheitsschraubloch
Mikrofon
Stromkontakte
Hardware-Anschlüsse
Micro-SD-Kartenschlitz
18650 Akku-Pack
Sicherheitsschraube
Montage Schraublöcher
3
2
1
4
6
5
8
7
10
9
12
11
13
15
16
14
12
11
13
14
2 1
4
5
10
6
7
8
9
3
1615

4. 4.Installation der Batterie
Die Batterien sind in der Türklingel vorinstalliert, wobei in die positiven Pole
ein Isolierfilm eingelegt ist. Bitteentfernen Sie die Folie und legen Sie das
Akkupack zurück ins Fach, mit den positiven Polen nach oben!
HINWEIS:
IEine unsachgemäße Installation der Batterie führt zu Schäden an den
internen Komponenten und kann zu schweren Verletzungen führen.
Die Batterien im Innern der Türklingel sind nicht vollständig geladen, was den
Sicherheitsvorschriften für den Transport entspricht.
Bitte laden Sie die Akkus mit einem USB-kompatiblen Wandladegerät
(nicht im Lieferumfang enthalten) und dem mitgelieferten USB-Kabel
für ca. 8~10 Stunden vor der Installation auf.
5. Akkus aufladen
- 14 -
7. WLAN Setup
Bevor Sie mit der WLAN-Konfiguration beginnen, beachten Sie bitte die folgenden Hinweise:
1).Die Türklingel funktioniert mit 2,4-GHz WLAN, aber nicht mit 5-GHz WLAN.
2).Vermeiden Sie die Verwendung von Sonderzeichen oder Symbolen wie
)(@~!#$%^&*... , weder in Ihrem
WLAN-Namen noch in Ihrem Passwort.
3). Führen Sie die Konfiguration in der Nähe Ihres WLAN-Routers durch.
6. Laden Sie die App herunter
Laden Sie die'CloudEdge' App vom GooglePlayTM oder dem AppStoreTM herunter und installieren Sie
sie. Die App ist auch verfügbar, indem Sie die QR-Codes auf der rechten Seite mit Ihrem QR-Code-Scanner
auf Ihrem Smartphone einscannen.
HINWEIS:
Google PlayTM ist ist ein Warenzeichen der Google Inc
App StoreTMist eine Dienstleistungsmarke von Apple Inc.
Starten Sie die 'CloudEdge'-Anwendung und registrieren Sie ein Konto mit Ihrer Mobiltelefonnummer oder
E-Mail-ID. Starten Sie die WLAN-Konfiguration, indem Sie den In-App-Anweisungen folgen oder sich auf
die folgenden Anleitungsschritte beziehen.
Android
iOS
CloudEdge
isolating film

Mitteilungen
056853326
9:55
12%
9:55
9:55
9:55
Mitteilungen
Anleitung Schritte:
9:55
2. Wählen Sie Türklingel. 3. Überprüfen Sie den
Stromstatus. 4. Aktivieren Sie die
Türklingel. 5. Setzen Sie das Gerät zurück.
- 15 -
8. Einen Test durchführen
Tippen Sie nach dem Setup auf das Live-Ansichtsfenster in der App für einen Test. Bringen Sie dann Ihre
Türklingel nach draußen zum Installationsort und führen Sie dort einen Test durch. Stellen Sie sicher, dass
der Montageort von einem starken 2,4-GHz WLAN-Signal abgedeckt ist.
HINWEIS: Wenn die Videoqualität von der Türklingel draußen nicht so gut ist wie drinnen, müssen Sie den
Router möglicherweise näher an den Montageort bringen oder in einen WLAN-Extender investieren.
9:55
15~25cm
5~8 in
6. WLAN kennwort eingeben
1.Tippen Sie auf "+", um
das Gerät hinzufügen.
7. QR-Code generieren 8. QR Code Scannen 9. Warten Sie auf WLAN-
verbindung 10. Hinzufügen des Geräts
abgeschlossen

HD
Bitrate: 41.99KB/s
Live-Modus Geschichte
Gegensprechanlag
e
Bewegungserkenn
ung
Aufnahme
Cloud
- 16 -
9. Live Ansicht
3
6
4
1
7
2
5
Liveansicht beenden
Einstellungsmenü
Akku-Status
Lautstärke ein/aus
HD/SD Schalter
Vollbildschirm-Anzeige
Stream bitrate
9
10
13
8
11
14
12
WLAN signal status
Screenshot-Taste
Mit der Szene reden
Am Handy aufnehmen
Körpererkennung ein/aus
Benachrichtigungs-Verlauf
Cloud-Speicherdienst
Hinweis:
Live-Ansicht löst keine Geräteaufzeichnung aus.
10. Wiedergabe
Wenn die Micro-SD-Karte richtig installiert ist, können Sie die Videoclips abspielen, die nach erkannten
Bewegungen oder Besuchen aufgenommen wurden. (Die Live-Anzeige löst keine Geräteaufzeichnung aus).
Sie können auch Videoclips in der Wolke sichern, jedoch nur, wenn Sie den Cloud-Storage-Service aktiviert
haben (Gebühr nach einem 7-Tage-Gratis-Test).
Live-Modus-Oberfläche
Verlauf Wiedergabe-
schnittstelle Cloud-Speicherschnittstelle
10:58:06
10:57 10:57:30 10:58 10:58:30 10:59 10:59:
Kalender Aufnahme
Alarm
10:58:06
10:57 10:57:30 10:58 10:58:30 10:59 10:59:
Calendar
Alarm
Nov 2019
Tag Eins Zwei Drei Vier Fünf sechs
27 28 29 30 31 1 2
10 11 12 13 14 15 16
17 18 19 23 21 23
24 25 26 27 28 29 30
3 4 5 6 7 8 9
3 4 5 6 71 2
22
10:58:06
10:57 10:57:30 10:58 10:58:30 10:59 10:59:
Besuchsnachricht 09:29:30
Besuchsnachricht 10:10:02
Besuchsnachricht 10:56:56
Bewegunserkennung 10:58:45
Bewegunserkennung 10:59:21
Besuchsnachricht 13:09:30
Bewegunserkennung 14:39:51
10:57 10:57:30 10:58 10:58:30 10:59 10:59:
Cloud storage ist nicht aktiv
aktiviereb Sie
Suche nach videoclips
nach Datum Suche nach videoclips
nach Ereignissen
10:58:06
10:57 10:57:30 10:58 10:58:30 10:59 10:59:
Visitor Message 09:29:30
Visitor Message 10:10:02
Visitor Message 10:56:56
Moton Detection 10:58:45
Motion Detection10:59:21
Visitor Message 13:09:30
Motion Detection 14:39:51
Zeitleiste
hineinzoomen/
Rauszoomen
Live-Modus Geschichte Cloud Live-Modus Geschichte Cloud

Es können maximal 3 Sprachnachrichten (jeweils max. 10 Sekunden) in die Türklingel eingespielt werden,
die es Ihnen ermöglicht, schnell auf Ihre Besucher zu reagieren, wenn Sie nicht in der Lage sind, den
Türklingelruf zu beantworten.
Hinweis: Einstellung  Grundfunktion  Gastgeber verlässt Nachricht  Symbol drücken und halten
to Zum Aufnehmen von Sprachnachrichten --> Drücken Sie die Türklingeltaste --> Spielen Sie die
ausgewählte Sprachnachricht als Antwort auf einen Türklingelruf ab.
- 17 -
11. Sprachnachrichten hinterlassen
Schritte: die Einstellungen >> Gerätefreigabe >> Auf “Hinzufügen” tippen >> Auf “Konto” tippen >>
Konto eintippenID>> Freigabe bestätigen
12. Ihr Gerät teilen
Gemeinsame Nutzung durch Kontensuche
Voicemail
Meine voicemail
Voicemail 1
Voicemail 2
Halten Sie die Taste gedrückt, um die
Voicemail aufzunehmen
0:04
3
057394082
Besucher besuchen
Klick hier
057394082
Voicemail senden
9:55
1372896****
Lil
Geteilt
Anfordern
mophie2019**@gmail.com
Mophie
Hinzufügen
Gerätefreigabe
9:55
Hinzufügen
2
Letzte Kontakte
QR-Code Scannen Konto
3
9:55
Suche
Bitter geben Sie das Konto Ihrer Familie ein
mophie2019**@gmail.com|
4
5
2
1
Cloud-Speicherdienst
1
Cloud-Speicherdienst
Besucher besuchen
Voice Msg 1
Voice Msg 2
Voice Msg 3
Stornieren
Gerätefreigabe Gerätefreigabe Gerätefreigabe
Wie Geräte zu teilen?