CTS iCPE User manual

1
iCPE
Gateway Controller
Network Management User’s Manual
Version 0.90

2
Trademarks
Contents are subject to revision without prior notice.
All other trademarks remain the properties of their owners.
Copyright Statement
This publication may not be reproduced as a whole or in part, in any way whatsoever unless prior consent has
been obtained from the owner.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limitations are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult your local distributors or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission limits.
Changes or modifications to the equipment, which are not approved by the party responsible for compliance,
could affect the user’s authority to operate the equipment.
Copyright © 2016All Rights Reserved.
Company has an on-going policy of upgrading its products and it may be possible that information in this
document is not up-to-date. Please check with your local distributors for the latest information. No part of this
document can be copied or reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.

3
Manual Version
Firmware Version
Modification
Date
0.90
1.00.00
First Release
20160119

4
Table of Content
1. OVERVIEW.......................................................................................................................8
1.1 Management Preparations............................................................................................................ 8
1.1.1 Connecting the gateway controller ..............................................................................8
1.1.2 Assigning IP Addresses .............................................................................................8
2. Command Line Interface (CLI).........................................................................................10
2.1 Remote Console Management-Telnet ........................................................................................ 10
2.2 Navigating CLI............................................................................................................................11
2.2.1 General Commands................................................................................................. 11
2.2.2 Quick Keys.............................................................................................................12
2.2.3 Command Format ...................................................................................................12
2.2.4 Login Username & Password ...................................................................................14
2.3 User Mode.................................................................................................................................. 14
2.4 Privileged Mode......................................................................................................................... 15
2.4.1 Copy-cfg Command ................................................................................................15
2.4.2 Firmware Command................................................................................................16
2.4.3 Reload Command....................................................................................................16
2.4.4 Write Command......................................................................................................17
2.4.5 Configure Command ...............................................................................................17
2.5 Configuration Mode................................................................................................................... 17
2.5.1 Entering Interface Numbers......................................................................................18
2.5.2 No Command .........................................................................................................18
2.5.3 Show Command......................................................................................................18
2.5.4 IP Command...........................................................................................................21
2.5.5 MAC Command......................................................................................................23
2.5.6 Management Command...........................................................................................23
2.5.7 Mirror Command ....................................................................................................24
2.5.8 MQTT Command....................................................................................................24
2.5.9 NTP Command.......................................................................................................26
2.5.10 QoS Command......................................................................................................27
2.5.11 Security Command ................................................................................................33
2.5.12 SNMP-Server Command........................................................................................33
2.5.13 Switch Command..................................................................................................36

5
2.5.14 Switch-info Command...........................................................................................36
2.5.15 Syslog Command ..................................................................................................38
2.5.16 USB Command.....................................................................................................39
2.5.17 User Command .....................................................................................................39
2.5.18 VLAN Command ..................................................................................................41
2.5.19 Z-Wave Command.................................................................................................47
2.5.20 Interface Command ...............................................................................................48
2.5.21 Show interface statistics Command .........................................................................51
2.5.22 Show log Command ..............................................................................................52
2.5.23 Show default-config, running-config and start-up-config Command ...........................52
2.5.24 Show battery status Command................................................................................52
3. WEB MANAGEMENT.....................................................................................................53
3.1 System Information.................................................................................................................... 55
3.2 User Authentication.................................................................................................................... 56
3.3 Network Management................................................................................................................ 59
3.3.1 Network Configuration............................................................................................60
3.3.2 System Service Configuration...................................................................................62
3.3.3 Telnet Configuration ...............................................................................................62
3.3.4 Time Server Configuration.......................................................................................63
3.3.5 Device Community .................................................................................................64
3.3.6 Trap Destination .....................................................................................................65
3.3.7 Trap Configuration..................................................................................................66
3.3.8 Mal-attempt Log Configuration ................................................................................66
3.4 Switch Management................................................................................................................... 67
3.4.1 Switch Configuration...............................................................................................68
3.4.2 Broadcast Storm Control..........................................................................................69
3.4.3 Port Configuration...................................................................................................70
3.4.4 Rate Limit Configuration .........................................................................................71
3.4.5 QoS Priority Configuration ......................................................................................71
3.4.6 VLAN Configuration...............................................................................................75
3.4.6.1 Port Based VLAN.............................................................................................77
3.4.6.1.1 Configure Port Based VLAN .......................................................................77
3.4.6.2 IEEE 802.1q Tag VLAN...................................................................................79

6
3.4.6.2.1 Trunk VLAN Table.....................................................................................79
3.4.6.2.2 VLAN Interface..........................................................................................80
3.4.6.2.3 Management VLAN....................................................................................81
3.4.7 Mirroring Configuration...........................................................................................82
3.4.8 Filter Configuration.................................................................................................83
3.5 Switch Monitor........................................................................................................................... 83
3.5.1 Switch Port Status...................................................................................................84
3.5.2 Port Counters Rates.................................................................................................85
3.5.2.1 Port Traffic Statistics (Rates)..............................................................................85
3.5.2.2 Port Packet Error Statistics (Rates)......................................................................86
3.5.2.3 Port Packet Analysis Statistics (Rates).................................................................87
3.5.3 Port Counters Events ...............................................................................................87
3.5.3.1 Port Traffic Statistics (Events)............................................................................88
3.5.3.2 Port Packet Error Statistics (Events)....................................................................88
3.5.3.3 Port Packet Analysis Statistics (Events)...............................................................89
3.5.4 IEEE 802.1q Tag VLAN Table..................................................................................90
3.5.5 MAC Address Table ................................................................................................90
3.5.6 Battery ROM Status ................................................................................................91
3.6 USB Config & Status ................................................................................................................. 91
3.7 MQTT Configuration ................................................................................................................. 92
3.8 Z-Wave....................................................................................................................................... 94
3.8.1 Z-Wave Network Manager .......................................................................................94
3.8.1.1 Adding and Removing The Controller in An Existing Network..............................96
3.8.1.2 How to Initiate A Replication of Network Information from The Controller to Another
Controller ...................................................................................................................96
3.8.1.3 Assigning The Controller as an SIS.....................................................................97
3.8.2 Z-Wave Node Controller..........................................................................................97
3.8.2.1 Notification Settings..........................................................................................99
3.8.2.2 Power Level Settings.......................................................................................108
3.8.2.3 Association Settings........................................................................................109
3.8.2.4 Battery Status .................................................................................................111
3.8.2.5 Door Lock Settings .........................................................................................111
3.8.2.6 User Code Settings..........................................................................................113

7
3.8.2.7 Wake Up Settings ...........................................................................................113
3.8.2.8 Sensor Multilevel Settings ...............................................................................114
3.8.2.9 Basic Settings.................................................................................................117
3.8.2.10 Binary Settings .............................................................................................117
3.8.2.11 Switch Multilevel Settings .............................................................................118
3.8.2.12 Meter Settings...............................................................................................119
3.8.2.13 Thermostat Setpoint Settings..........................................................................121
3.8.2.14 Thermostat Mode Settings..............................................................................122
3.8.2.15 Configuration Settings...................................................................................123
3.9 Z-Wave Utility.......................................................................................................................... 124
3.9.1 Z-Wave HTTP Upgrade .........................................................................................124
3.9.2 Z-Wave Upgrade...................................................................................................125
3.9.3 Z-Wave Save Configuration ...................................................................................126
3.10 System Utility......................................................................................................................... 126
3.10.1 Ping ...................................................................................................................127
3.10.2 Event Log...........................................................................................................128
3.10.3 HTTP Upgrade....................................................................................................128
3.10.4 FTP/TFTP Upgrade .............................................................................................129
3.10.5 Load Factory Settings ..........................................................................................131
3.10.6 Load Factory Settings Except Network Configuration .............................................132
3.11 Save Configuration................................................................................................................. 132
3.12 Reset System .......................................................................................................................... 133
3.13 Logout .................................................................................................................................... 133
APPENDIXA: DHCPAuto-Provisioning Setup...................................................................134
APPENDIX B: Free RADIUS readme...............................................................................143
APPENDIX C: Z-Wave Terminology................................................................................144
APPENDIX D: Control Command Class Table...............................................................145

8
1. OVERVIEW
This controller is a Z-Wave static controller.
This product can be included and operated in any Z-Wave network with other Z-Wave certified
devices from other manufacturers and/or other applications. All non-battery operated nodes within the
network will act as repeaters regardless of vendor to increase reliability of the network.
This device is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus
message to Enabled Z-Wave Plus devices.
Replication refers to the protocol replication between Controllers that is used to exchange protocol data
between different Controllers of the same network.
The controller ignores any Basic Command class if receiving Basic Set from a sensor.
The controller supports Association Command Class. It has one association group, which is Lifeline
group with grouping identifier equal to 1. Maximum number of devices that can be added to the group
is 1. When the device is reset, this group returns Device Reset Locally notification.
The controller supports the listed browsers: IE, Firefox and Google Chrome.
1.1 Management Preparations
The gateway controller can be accessed through both Telnet connection and a web browser such as
Internet Explorer, Google Chrome or Firefox, etc…Before you can access the gateway controller and
configure it, you need to connect cables properly.
1.1.1 Connecting the gateway controller
It is extremely important that proper cables are used with correct pin arrangements when connecting
the gateway controller to other devices such as switches, hubs, workstations, etc..
10/100/1000Base-T RJ-45 Ports
Depending on the model that you purchased, 2 10/100/1000Base-T RJ-45 ports are located on
the front panel of the Gateway controller. These RJ-45 ports allow users to connect their
traditional copper-based Ethernet devices to network. All these ports support auto-negotiation
and MDI/MDIX auto-crossover, i.e. the crossover or straight through CAT-5 cable may be used.
1.1.2 Assigning IP Addresses
IP addresses have the format n.n.n.n, for example 168.168.8.100.
IP addresses are made up of two parts:

9
The first part (168.168.XXX.XXX in the example) indicates network address identifying the
network where the device resides. Network addresses are assigned by three allocation
organizations. Depending on your location, each allocation organization assigns a globally
unique network number to each network that wishes to connect to the Internet.
The second part (XXX.XXX.8.100 in the example) identifies the device within the network.
Assigning unique device numbers is your responsibility. If you are unsure of the IP addresses
allocated to you, consult the allocation organization from which your IP addresses were
obtained.
Remember that an address can be assigned to only one device on a network. If you connect to the
outside, you must change all the arbitrary IP addresses to comply with those you have been allocated
by the allocation organization. If you do not do this, your outside communications will not be
connected.
A subnet mask is a filtering system for IP addresses. It allows you to further subdivide your network.
You must use the proper subnet mask for a proper operation of a network with subnets defined.

10
2. Command Line Interface (CLI)
This chapter guides you to use Command Line Interface (CLI) via Telnet connection, specifically in:
Configuring the system
Resetting the system
Upgrading newly released firmware
2.1 Remote Console Management-Telnet
You can use Command Line Interface to manage the Gateway controller via Telnet session. For first-
time users, you must first assign a unique IP address to the Gateway Controller before you can manage
it remotely. Use any one of the RJ-45 ports on the front panel as the temporary management console
port to login to the device with the default username & password and then assign the IP address using
IP command in Global Configuration mode.
Follow steps described below to access the Gateway Controller through Telnet session:
Step 1. Use any one of the RJ-45 ports on the front panel as a temporary management console
port to login to the Gateway Controller.
Step 2. Ask the DHCP server for IP address and run Telnet client and connect to the given IP
address. For first-time users, make sure the IP address of your PC or workstation is
assigned to an IP address between 192.168.0.2 and 192.168.0.254 with subnet mask
255.255.255.0.
Step 3. When asked for a username, enter “admin”. When asked for a password, leave the
password field blank and press Enter (by default, no password is required.)
Step 4. If you enter CLI successfully, the prompt display Switch> (the model name of your
device together with a greater than sign) will appear on the screen.
Step 5. Once you enter CLI successfully, you can set up the Switch’s IP address, subnet mask
and the default gateway using “IP” command in Global Configuration mode. The telnet
session will be terminated immediately once the IP address of the Switch has been
changed.
Step 6. Use new IP address to login to the Gateway Controller via Telnet session again.
Limitation: Only one active Telnet session can access the Gateway Controller at a time.