Philips Dynalite dmc2 User manual

DMC2

Dynalite Modular Controller (2Output Modules)

Installation Instructions

Warning…………………………………………….. 2 Final Checks……………………..……………….. 6

Features……………………………………………..2 Dimensions…………….……………………….….. 7

Important Safeguards…………………………….. 2 Specications………………………………………. 8

Internal View……………………………………….. 3

Mounting…………………………………….……… 4

Module mounting…………………..……………… 5

DMC2 Installation Instructions Rev B Specications subject to change without notice

Dynalite manufactured by WMGD Pty Ltd (ABN 33 097 246 921) Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia Tel: +61 2 8338 9899 Fax: +61 2 8338 9333

E-Mail: [email protected] Web: http://philips.com/dynalite

DMC2 Installation Instructions Rev 03

Features

• Two Control Module Locations

Wide range of interchangeable output modules

available to meet the capacity and control type

needs of any project.

Modules supplied separately.

The DMC2 is only compatible with Philips

Dynalite modules.

• Communication Module

Allows the controller to be used with a variety of

supported protocols.

• Convection Cooled

The DMC2 is ventilated, and requires no active

cooling system when installed in accordance with

these instructions.

• Multiple Control Options

The DMC2 is designed to operate as part of a

network system that can be structured to meet the

project’s needs.

• Simple Installation

The enclosure is suitable for both surface and

recess mount. Cabling knockouts for supply and

load cables are provided at the top, side and

back of the enclosure for supply and load cables.

Cabling knockouts for Control cables (Class 2 /

SELV) are located at the bottom of enclosure.

Important Safeguards

Read the Instructions – We recommend that you read

this document prior to commencement of installation. Do

not energize the DMC until all steps of the installation

procedure on page 6 are complete.

Installation of the home and building automation and

control system shall comply with HD60364-4-41 where

applicable.

Special Programming – Once assembled, powered

and terminated correctly, this device will operate in basic

mode. A new Philips Dynalite user interface on the same

network will turn all output lighting channels on from

button 1 and off from button 4 allowing testing of network

cables and terminations. Advanced functions and custom

presets can then be congured via the EnvisionProject

commissioning software.

If commissioning services are required, contact your local

distributor for details.

High Voltage Insulation Test – Do not Megger test any

circuitry connected to the dimming system, as damage to

the electronics may result.

Power Sources – This device should only be operated

from the type of supply specied on installed modules.

This device must be earthed.

Mounting Location – This device must be mounted

upright on a vertical surface (refer to page 4 for mounting

instructions), with a minimum clearance of 200mm on all

sides of the front cover.

Install in a dry, well-ventilated location.

Controllers may emit some audible noise such as

humming or relay chatter. Take this into account when

deciding the mounting location.

Data Cable – The recommended cable for connections

to the serial port is screened stranded RS485 compatible

CAT-5E data cable with three twisted pairs. Refer to the

installation instructions for the communication module for

more cabling information. This cable must be segregated

from mains and Class 1 cables as per local electrical

code. If anticipated cable runs are over 600 meters for

serial cables, consult your dealer for advice. Do not cut or

terminate live data cables.

Manual Override Keypad – The Manual Override Keypad

does not provide permanent isolation. Isolate at the supply

before performing work on load circuits.

DMC2 Installation Instructions Rev 03

Internal View

Supply

module

install

location

Control

module 1

install

location

Control

module 2

install

location

Comms module

install location

Communication

bus and power

connection

Communication

bus connection

Communication

bus connection

Surface mounting sleeve Wall mounting point Knockouts for unit supply Wall mounting point

Communication

bus cover

Knockouts for lighting

group channels

High voltage barrier

Data cable

entry points

Surface mounting sleeve

For spare parts, please call your nearest Philips Dynalite Customer Service Centre.

Communication

bus connection

DMC2 Installation Instructions Rev 03

Mounting

For surface mounting, four mounting points have been

provided. Refer to the location of the mounting points in the

dimension drawings on page 7 of this document.

For recess mounting, four holes suitable for M6 (1/4”)

fasteners have been provided on side walls as shown below.

Minimum spacing between studs is 380mm (15”), minimum

mounting depth 103mm (4.1”)

Allow for Cable Entry

Supply and load cables can enter the enclosure through

knockouts at the top, side or back. An alternative method

is to stand the enclosure off from the mounting surface by

mounting it on a cable tray or a Unistrut-style product.

The control cables enter at the bottom of the enclosure.

Control cables should never be run in the mains voltage

sections of the enclosure.

Energizing the Device

If it is necessary to energize load circuits for test purposes

before any control cables are connected, it is acceptable

to replace the top cover and energize the device, as the

default factory programming is to have all channels set

to 100% output. Use the manual override keypad on the

communication module to control individual channels.

This device should be de-energized before terminating the

control and data cables.

Select a suitable location

This device is designed for indoor use only. If

installing in an outdoor location, the DMC2 must

be housed in a suitable well-ventilated enclosure.

Choose a dry location that will be accessible after the

installation is complete. To ensure sufcient cooling,

the DMC2 must be mounted vertically, as shown

above. The DMC2 requires a minimum air gap of

200mm (8”) around the front, sides, top and bottom of

the front cover. This air gap is also required to ensure

serviceability of the DMC2 without complete removal

from the mounting surface.

The device may emit some audible noise during

operation. Take this into account when deciding the

mounting location.

Ensure no dust or other debris enters the device during

installation. Do not leave the front cover off for any length

of time. Excessive dust and dirt can impede the cooling of

internal components.

DMC2 Installation Instructions Rev 03

Module mounting

Before starting:

Remove the knockouts you intend to run the supply cables through – lighting group supply and

network supply rst – then mount the DMC2 (surface or recessed, as required). Once the unit is

secured to the intended mounting wall follow the steps below for the different module mounting.

Supply Cables:

The supply input terminals are located on the DSM Module toward the top of the enclosure and

consist of Neutral and Phase terminals, all of which will accept up to 16mm2 cables. The supply

cables should have a capacity of 32A per phase for three-phase supply or up to 63A for single

phase, to allow the device to be loaded to its maximum capacity. The earth bar is located in the

DMC unit near the top of the case.

To install the Communication, Supply and Control modules:

1. Connect the module ribbon cable to its respective plug.

2. On the left hand side of the module there are two locating tabs which will line up with the

DMC communication bus cover. Slide the tabs into these locations and secure the module by

tightening the xing screw to the enclosure.

3. Connect the modules to the internal wiring harness and eld wiring as applicable.

There are two control module bays within the DMC2. Any control module can be tted to any of

the two locations.

Check the supplied module installation instructions for additional advice.

DMC2 Installation Instructions Rev 03

1. After removing both front covers and the required knockouts for the power supply, networking cable and lighting group

channels, mount the unit in its desired location. Once secured, the DMC2 unit is ready for the internal modules to be

mounted.

2. Mount the communication module below the high-voltage barrier of the DMC2. Refer to the communications module

installation instructions for more details before proceeding.

3. Mount the power supply module in the top of the DMC2. Refer to the power supply module installation instructions for

more details before proceeding.

4. Mount the control modules in the remaining module spaces. Any control module can be mounted in any location and

any module location can be left empty. Refer to the control module installation instructions for more details.

5. Connect the supplied wiring loom to the DMC2 as shown. Use only the loom supplied with the unit, and do not break or

modify the loom in any way. Make sure the labels on the loom correspond to the wiring on each module. For modules

requiring termination, remove the black insulating caps from the loom before terminating to the load and supply

modules. For any module location that is not populated or does not require termination, the corresponding insulating

caps (or mains-rated isolating electrical terminators) must remain in place on the harness. Terminate the correctly rated

supply to each module but do not energize.

6. Check and retighten all terminals. Remove the knockout detail on the front cover as required. Replace the top and

bottom cover plates, and make sure all screws are tightened securely. Stick the labels provided with the modules on the

cover plate to indicate which module is installed in each location.

7. The unit is now ready to be energized. If required, the bottom cover can be removed when energized to access the

override key matrix.

DMC2 Installation Instructions Rev 03

Dimensions

380mm

15.0in

540mm

21.3in

103mm

4.1in

285mm

11.2in

440mm

17.3in

DMC2 Installation Instructions Rev 03

Specication

Control Modules: 2 x Control module locations

Cable Entry: Supply/Control

Top: 4 x 28.2mm (1.1”) 2 x 22.2mm (0.87”)

Side: 7 x 28.2 (1.1”) 7 x 22.2mm (0.87”)

Back: 4 x 28.2mm (1.1”) 3 x 22.2mm (0.87”)

Data

Side: 1 x 28.2mm (1.1”)

Bottom: 1 x 28.2mm (1.1”)

Note:

28.2mm (1.1”) opening is suitable for 3/4” conduit

22.2mm (0.87”) opening is suitable for 1/2” conduit

Compliance: DMC2-UL: UL, CSA, CE, RCM, FCC, ICES-003

Overvoltage category III, Pollution Degree II

DMC2-CE: CE, RCM, Overvoltage category III, Pollution Degree II

NOTE:

• The temperature limits and current-carrying capacities of the communication

wires specied in HD 384.5.523 shall not be exceeded.

• Installation of home and building automation control shall comply with HD 60364-

4-41.

• Network Topology for installation is Daisy Chain.

Input: Voltage rating: 120/230/277 VAC +10% / -15%

50/60 Hz 3-Phase, 4-Wire (Y), or Single Phase

Current rating: 32 A per phase for 3-phase supply, or single phase 63 A max

Operating Environment: 0°C to 40°C (32°F to 104°F) ambient temperature

0% to 90% RH non-condensing

Shipping and Storage: -25°C to 60°C (-13°F to 140°F) ambient temperature

0% to 90% RH non-condensing

Construction: Galvanized Steel case with powder coated front covers

Dimensions: H: 540mm (21.3”)

W: 380mm (15”)

D: 106mm (4.2”)

Weight: 7.71 kg (17 lbs) (excluding all modules)

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Any modications not approved by the manufacturer of this device could void the user’s authority to operate this device.

Compliance to Industry Canada ICES-003: CAN ICES-3(B)/NMB-3(B)

DMC2 Installation Instructions Rev 03 Specications subject to change without notice

Dynalite manufactured by WMGD Pty Ltd (ABN 33 097 246 921) Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia Tel: +61 2 8338 9899 Fax: +61 2 8338 9333

E-Mail: [email protected] Web: http://philips.com/dynalite

Table of contents

Other Philips Controllers manuals