Cub Cadet 490-900-C066 User manual

May 21, 2015 Bluetooth®Enabled Maintenance Meter Option
XT1, XT2 Enduro Series or RZT L/S Models Without Factory Installed Bluetooth®enabled
maintenance meter.
BLUETOOTH®ENABLED MAINTENANCE METER
PURPOSE:
To offer those customers who did not purchase a model that had the Bluetooth®enabled maintenance meter installed at
the factory, the option to install a Bluetooth®enabled maintenance meter that works with CUB CONNECT™.
Models Affected:
Subject:Date:
Model Years 2015 and After Production Only.
Serial Number
Range Affected:
490-900-C066 OPTIONAL KIT
NOTE: These materials are prepared for use by trained technicians who are experienced in the service and repair of
equipment of the kind described in this publication, and are not intended for use by untrained or inexperienced
individuals. Such individuals should seek the assistance of an authorized service technician or dealer.
NOTE: Always wear eye protection while servicing equipment. Wear hearing protection when appropriate. Always work
in a well ventilated area and follow all safety precautions when dealing with combustible materials.
NOTE: Left (LH) and Right (RH) sides are determined from the operator’s position and facing in the forward direction.
ITEM
NO. PART NUMBER QTY DESCRIPTION
1 725-06221 1 METER-SVC MNDR/HOUR BLUE TOOTH
2 777I25270 1 LBL-SVC MNDR/HR MTR BLUE TOOTH
3 777I25406 1 LBL-SVC MNDR/HR MTR BTE RZT-S/L
490-900-C066 Kit Contents
Instruction sheet included with kit.
FIGURE 1
Optional Kit 490-900-C066 1 of 9 Form No. 769-10822 /00
725-06221 777I25406
13
NOTE: For RZT installation follow instructions on Pages 2-3. Estimated installation time 15 - 20 minutes.
NOTE: For XT1 or XT2 installation follow instructions on Pages 4-8. Estimated installation time 15 - 20 minutes.
NOTE: Installation time does not include steps (page 9) to activate / set-up CUB CONNECT™Mobile App.
RZT Label
777I25270
2
Rider Label

Optional Kit 490-900-C066 2 of 9 Form No. 769-10822 /00
RZT Installation Instructions:
1. Park the rider on a flat level surface. Engage the park-
ing brake. Lower deck to lowest position.
2. Disconnect the negative battery cable from the nega-
tive battery terminal, then disconnect the positive battery
cable from the positive battery terminal.
3. Allow the unit to cool to ambient temperature before
proceeding.
4. Reach up inside of the right hand pod and disconnect
the main wire harness connector from the maintenance
meter by depressing the tab and pulling the connector
down. See Figure 2.
8. Make sure the top surface of the right hand pod is free
of the old label, dirt, etc. Clean as needed.
9. Install Item #1 (725-06221) Bluetooth®enabled Mainte-
nance meter in the square opening as shown In Figure 5.
NOTE: The terminal block must be at the bottom,
above the PTO switch as shown in Figure 5.
FIGURE 2
5. Carefully peel/remove the existing maintenance meter
label away from the pod and top of the maintenance
meter. See Figure 3.
FIGURE 3
6. Reach up inside of the right hand pod and squeeze the
two (2) tabs inward to release the maintenance meter
from the right hand pod.
7. Push the maintenance meter out the top of the right
hand pod. See Figure 4. Discard the maintenance meter.
Remove Label
FIGURE 4
FIGURE 5
Terminal Block Item #1
(725-06221)
Tab
Tab
Wire Harness
Connector
Depress Tab
Right Hand Pod
10. Push the Bluetooth®enabled maintenance meter all
the way into the right hand pod until the two (2) tabs snap
in place.
11. Remove the black rectangular section from the center
of Item #3 (777I25406) RZT Bluetooth®enabled mainte-
nance meter label as shown in Figure 6 and discard.
Maintenance Meter

13. Make sure all air bubbles are removed from under the
label.
14. Reach up inside the right hand pod and install the
wire harness connector to the Bluetooth®enabled main-
tenance meter. Confirm that the wire harness connector
snapped in place.
15. Connect the positive battery cable to the positive bat-
tery terminal, then connect the negative battery cable to
the negative battery terminal.
16. Turn the key to the on position, the new Bluetooth®
enabled maintenance meter display should show the
hours.
17. Start the rider and confirm the Bluetooth®enabled
maintenance meter is functioning correctly.
NOTE: Connect the Bluetooth®enabled maintenance
meter to your smartphone by downloading the Cub
Connect™App for your Bluetooth®capable Android
or iOS device. See Page 9 for instructions.
12. Install Item #3 (777I25406) RZT Bluetooth®enabled
maintenance meter label. Carefully align the label over
the maintenance meter so that the open rectangular sec-
tion is centered over the silver rectangular LCD display
and the left side of the label is aligned with the edge of
the throttle /choke control slot. See Figure 7.
Optional Kit 490-900-C066 3 of 9 Form No. 769-10822 /00
FIGURE 7
Item #3
(777I25406)
FIGURE 6
Remove Rectangular Section
Item #3
(777I25406)

XT1 or XT2 Installation Instructions:
18. Park the rider on a flat level surface. Engage the
parking brake.
19. Disconnect the negative battery cable from the nega-
tive battery terminal, then disconnect the positive battery
cable from the positive battery terminal.
20. Allow the unit to cool to ambient temperature before
proceeding.
21. Remove the steering wheel cap. See Figure 8.
26. Use a T-30 torx to remove the two (2) shoulder
screws that secure the steering shaft bearing to the
steering bearing mounting bracket. See Figure 11.
Optional Kit 490-900-C066 4 of 9 Form No. 769-10822 /00
FIGURE 10
Squeeze The Tabs
22. Remove the 5/16-24 x 0.850” screw that retains the
steering wheel to the steering wheel shaft. See Figure 9.
23. Remove the steering wheel.
24. Open the hood.
25. Remove the dash cap shown in Figure 10 by squeez-
ing the two (2) tabs together, then pushing the dash cap
towards the seat.
FIGURE 8
FIGURE 9
5/16-24 x 0.850” Screw
Steering Wheel Cap Dash Cap
Seat
FIGURE 11
27. Remove the steering shaft bearing by lifting up and
off the steering shaft.
Remove
Steering Shaft Bearing

Optional Kit 490-900-C066 5 of 9 Form No. 769-10822 /00
28. Carefully peel/remove the existing maintenance
meter label away from the upper dash and top of the
maintenance meter. See Figure 12.
FIGURE 12
Remove Label
29. Reach inside the opening in the top of the upper dash
and remove the wire harness connector from the mainte-
nance meter. Depress the tab then pull the connector
down See Figure 13.
FIGURE 13
30. Reach inside the opening again and squeeze the two
(2) tabs on the sides of the maintenance meter while
pushing up and out of the upper dash. See Figure 14. A
small flat blade screw driver may be used to assist in the
removal of the maintenance meter.
Upper Dash
31. Push the maintenance meter out of the upper dash.
Discard the maintenance meter.
32. Make sure the top surface of the upper dash is free of
the old label, dirt, etc. Clean as needed.
33. Install Item #1 (725-06221) Bluetooth®enabled main-
tenance meter in the square opening of the upper dash
as shown In Figure 15.
NOTE: The terminal block must be at the bottom of
the square opening as shown in Figure 15.
34. Push the Bluetooth®enabled maintenance meter all
the way into the upper dash until the two (2) tabs snap in
place.
35. Install the wire harness connector to the Bluetooth®
enabled maintenance meter. Confirm that the wire har-
ness connector snapped in place.
36. Remove the black rectangular section from the center
of Item #2 (777I25270) Rider Bluetooth®enabled mainte-
nance meter label as shown in Figure 16 and discard.
Wire Harness
Connector
Depress Tab
Tab
FIGURE 14
37. Install Item #2 (777I25270) Rider Bluetooth®enabled
maintenance meter label. Carefully align the label so that
the open rectangular section is centered over the silver
rectangular LCD display and parallel with the edge above
and below the Bluetooth®enabled maintenance meter
label. See Figure 17.
Upper Dash
Opening
Terminal Block
Item #1
(725-06221)
FIGURE 15
FIGURE 16
Item #2
(777I25270)
Remove Rectangular Section

Optional Kit 490-900-C066 6 of 9 Form No. 769-10822 /00
38. Make sure all air bubbles are removed from under the
label.
39. Install the steering shaft bearing over the steering
shaft. See Figure 18. Lower into position until the steer-
ing shaft bearing contacts the upper dash. See Figure 18.
40. Install the two (2) shoulder screws removed in Step
26 that secure the steering shaft bearing to the steering
bearing mounting bracket. Tighten the shoulder screws
to a torque of 68-85 in. lbs.
41. Install the dash cap. The dash cap has four (4) tabs
that lock into four holes in the top of the upper dash. See
Figure 19. NOTE: Only the two (2) right side tabs of
the dash cap and holes of the upper dash are visible
in Figure 19.
42. Set the dash cap on top of the upper dash so that it
just hangs over the back edge as shown circled in Figure
25. This positions the four (4) tabs of the dash cap into
the four (4) holes of the upper dash shown in Figure 20.
FIGURE 17
Item #2
(777I25270)
FIGURE 18
Steering Shaft Bearing
Upper Dash
FIGURE 19
Tabs On Dash Cap
Holes In Upper Dash
Upper Dash
Dash Cap
FIGURE 20
43. While holding light pressure downward, push the
dash cap towards the engine. This will allow the four (4)
tabs of the dash cap to lock into the four (4) holes of the
upper dash.
44. Figure 21 shows the rear locking tabs of the dash cap
in relation to the upper dash prior to Step 43 and after
Step 43.
Prior To
Step 43
After Step
43
Rear Locking Tabs Of Dash Cap
Upper Dash
Rear Locking Tabs Of Dash Cap
Locked Into Upper Dash
Upper Dash
FIGURE 21

Optional Kit 490-900-C066 7 of 9 Form No. 769-10822 /00
45. When properly installed the dash cap will align as
shown in Figure 22 by the red dotted lines.
46. Make sure the front wheels are facing straight for-
ward prior to installing the steering wheel.
47. Position the steering wheel as shown in Figure 23,
then install the steering wheel onto the steering shaft until
it contacts the top of the steering shaft.
FIGURE 22
Upper Dash
Dash Cap
FIGURE 23
48. Install the 5/16-24 x 0.850” screw removed in Step 22
to secure the steering wheel to the steering shaft. Torque
the screw to 18-22 ft. lbs. (216-264 in. lbs.).
49. Install the steering wheel cap into the center of the
steering wheel. The steering wheel cap has three (3)
locking tabs with one being larger. The larger locking tab
is to be at the 6 O’clock position when installing into the
steering wheel. See Figure 29.
Large Locking Tab
Steering Wheel Cap
6 O’clock Position
FIGURE 24
50. Close the hood.
51. Connect the positive battery cable to the positive bat-
tery terminal, then connect the negative battery cable to
the negative battery terminal.
52. Turn the key to the on position, the new Bluetooth®
enabled maintenance meter display should show the
hours.
53. Start the rider and confirm the Bluetooth®enabled
maintenance meter is functioning correctly.
NOTE: Connect the Bluetooth®enabled maintenance
meter to your smartphone by downloading the Cub
Connect™App for your Bluetooth®capable Android
or iOS device. See Page 9 for instructions

Optional Kit 490-900-C066 8 of 9 Form No. 769-10822 /00
THIS AREA LEFT INTENTIONALLY BLANK

Optional Kit 490-900-C066 9 of 9 Form No. 769-10822 /00
CubConnect™MobileAppBluetooth®Operation
DeviceCompatibility
CubConnect™iscompatiblewiththefollowingdevices:
∙iPhone4S/5/5S(iOS6orlater)
∙iPodTouch(iOS6orlaterandBluetooth®compatible)
∙Android4.3(orlaterandBluetooth®compatible)
SmartHourMeter
Thehourmeter“advertises”thehoursrunandthebatteryvoltageviaaBluetooth®antenna.Thereisonlyoneway
communication,meaningthehourmeterwilltalktotheBluetooth®apponly.
SetupConditions
WhensettinguptheCubConnect™App,itisimportanttomakesurethephonepowerisonandtheBluetooth®
settingison.Thekeyshouldbeinthe“on”positionandthephoneandequipmentshouldbewithin150ft.ofeach
other.ItisimportanttoremembertoturnofftheignitionwhendoneusingCubConnect™.
FinishingSetup
Tofinishthesetup,youmustenterthemodelandserialnumberofyourunit.Youwillneedtomanuallyenterthe11
digitfactorynumberfromtheIDtagandyoucanscanthebarcodefromtheIDtagfortheserialnumber.Oncethisis
donejustclickonthecontinuebutton.
NavigationMenu
Thereare6navigationoptionsthatyoucanchoosefrominthenavigationmenu:
∙Dashboard–Listsnumerousmaintenanceitemsyoucancheck
∙MaintenanceRecords–Listsallmaintenancethathasbeendonetotheunit.
∙Operator’sManual
∙ServiceCenters
∙ProductRegistration
∙CustomerService
Operator’sManual
WhenyoupulluptheOperator’sManual,youmustacceptthedisclaimerasyouwouldwhenyoupullituponlineand
youonlyhavetoacceptitonce.ThemanualdoesopenupinaPDFformat.
FindaServiceCenter
FindingaServiceCenteristhesameasusingtheDealerlocator.Enteryourzipcodeandthemileagerangeyouwant
andtheresultswillshowinamapvieworyoucanselectalistview.Youcanalsogetdirectionsandthephone
numberforthedealer.
ProductRegistration
YoucanregisteryourunitrightfromtheCubConnect™app.ProductregistrationislistedasanoptionintheNaviga‐
tionMenu.Youmustfillouttherequiredinformationandclickonthecompleteprocessbutton.Itwillreturntothe
dashboardandtheProductRegistrationshouldnolongerbevisible.