Kuntze Krypton Neon DIS Assembly instructions

Krypton Neon DIS Installation and Set Up Guide
Kuntze Instruments
3316 Leechburg Road | Lower Burrell | Pennsylvania | 15068
724-339-8510 | [e-mail] | kuntzeinsturments.com
General Steps
1. Mount the system upright on the wall
2. Insert clean sensor
Insert Disinfection sensor into the Flow Cell Chamber for the
Disinfection Sensor (5) and screw on the Disinfection Cable
3. Power on system
4. Check flow
5. Calibrate sensor
6. If needed, set user specific settings –see operations manual
a. ASR
b. 4 –20 mA
c. Relay Alarms
Key
1–Neon DIS Instrument
2–Argon Stabiflow
3–FTG Temperature Cable
4- Disinfection Cable
5–Flow Cell Chamber for Disinfection Sensor
6–Water Inflow Valve
7–Water Outflow Valve
8–Water Sampling Reference Valve
9–Mounting Board
Check Your Flow
Make sure the Water Sampling Reference Valve is in the closed position.
System needs proper flow to operate. “Digital input 1 – no water” will show on display screen if
flow is not strong enough.
Flow minimum: 5 psi Flow maximum: 87 psi
Power Requirements
System comes with US power cord
Line Voltage:
85-265 V AC, 50-60 Hz
Power Consumption:
10 VA
Cleaning Sensor
IMPORTANT: Sensor must be cleaned by
hand before being inserted into the chamber!
How to clean DIS sensor:
- Remove sensor from assembly and cable
- Wipe off any pollution with paper tissue, rinse
with water
- Clean metal bands with powder detergent (ex.
Comet), wipe gently
- Rinse with water and reinstall
Calibrating Sensor
DIS Sensor
1. IMPORTANT: Clean sensor before
proceeding with calibration!
2. Using water sample taken from Sampling
Reference Valve, perform DPD test
3. Menu > Cal > Cal DIS > enter DPD
reference value > Ok > Save

Krypton Neon DIS Installation and Set Up Guide
Kuntze Instruments
3316 Leechburg Road | Lower Burrell | Pennsylvania | 15068
724-339-8510 | [e-mail] | kuntzeinsturments.com
Spare Parts List
Sensors
Part Number
Name
Description
24135140K
Zirkon® DIS
Sensor: 2 gold rings, ceramic junction, Tepox gel, M12 plug (swivel PG 13.5), for Free Chlorine,
Chlorine dioxide, and Ozone
24137001K
Zirkon® FTG
Flow monitor, temperature sensor and ground for Argon Stabiflow
Cables
Part Number
Name
Description
44136406K
5SCR-M12-AE-1.0
Connection cable for disinfection sensor; Type of cable: 5-core, 5 x 0.25 Somme, screen; Cable
length: 0.8m; Type of plug: M12 (female, other end with wire sleeves; Temperature range: -
20…+70C
Rebuild Kits
To see exploded view of Argon Stabiflow, open manual to section 20.3.3 Operations and Maintenance
Part Number
Name
Description
39500005K
Argon® Connection pkg
Inlet, outlet and sample cock
3x ball valve 1/4"
2x hose attachment 1/4" 6/8 1x hose barb 1/4"
3x O-ring 6x3 FKM 3x O-ring 11x3 FKM
39500006K
Argon® spare parts pkg 1
Membrane springs and valve pin, 1 membrane, 1 spring pressure side, 1 spring chamber side, 1
valve pin
39500007K
Argon® spare parts pkg 2
Filter 5x stainless Steel 500um filter 5x o-ring FKM 26x1.5
39500008K
Argon® spare parts pkg 3
1x o-ring FKM 12x2; 1x o-ring FKM 73x2
1x o-ring FKM 26x2; 1x o-ring FKM 26x1,5
1x o-ring FKM 5x1,8; 3x o-ring FKM 6x3
1x o-ring FKM 19x2,5; 1x o-ring FKM 7,6x2,4
1x o-ring FKM 108x3; 3x o-ring FKM 11x3
39500011K
Argon® spare parts pkg 4
Spare parts inflow; 1x hex spud; 2x O-ring 26x2; 1x O-ring 5x1.8; 1x filter support; 1x ball