Endress+Hauser Proline Promass 83 User manual

BA066D/06/en/12.06
71035083
Valid as of version:
V 2.00.XX (Device software)
Description of Device Functions
Proline Promass 83
FOUNDATION Fieldbus
Coriolis Mass Flow Measuring System
9
0000 0001 0002 0003 0004 0005000
AAAA
1000 1001 1002 1003 1004 1005100
BAAB
2000 2001 2002 2003 2004 2005200
CAAC
3000 3001 3002 3003 3004 3005300
DAAD
4000 4001 4002 4003 4004 4005400
EAAE
5000 5001 5002 5003 5004500
FAAF
4200
5200
4201
5201
4202
5202
4203
5203
4204 4205420
520
2400 2401 2402 2403 2404 2405240
CCA
2200 2201 2202 2203 2204 2205220
CBA
0200 0201 0202 0203 0204 0205020
0000 0001 0002 0003 0004 0005000
AAAA
1000 1001 1002 1003 1004 1005100
BAAB
2000 2001 2002 2003 2004 2005200
CAAC
3000 3001 3002 3003 3004 3005300
DAAD
4000 4001 4002 4003 4004 4005400
EAAE
5000 5001 5002 5003 5004500
FAAF
4200
5200
4201
5201
4202
5202
4203
5203
4204 4205420
520
2400 2401 2402 2403 2404 2405240
CCA
2200 2201 2202 2203 2204 2205220
CBA
0200 0201 0202 0203 0204 0205020
1000 1001 10100
BAAB
2000 2001 20200
CAAC
3000 3001 30300
DAAD
4000 4001 40400
EAAE
5000 5001 50500
FAAF
4200
5200
4201
5201
4
5
420
520
2400 2401 24240
CCA
2200 2201 2220
CBA
0200 0201 0020

Device Functions Proline Promass 83 FOUNDATION Fieldbus
2Endress+Hauser
Registered trademarks
FOUNDATION™ Fieldbus
Registered trademark of Fieldbus FOUNDATION, Austin, USA
S-DAT®, T-DAT™, F-CHIP®, ToF Tool - Fieldtool®Package, Fieldcheck®, Applicator®
Pending or registered trademarks of Endress+Hauser Flowtec AG, Reinach, CH
Operation Proline Promass 83 FOUNDATION Fieldbus
- with local operation: see page 3
- with FOUNDATION Fieldbus: see page 103

Device Functions Proline Promass 83 FOUNDATION Fieldbus Table of contents for local operation
Endress+Hauser 3
Table of contents for local operation
1 Notes on using this manual . . . . . . . . . . . . 5
1.1 Using the table of contents to locate
a function description . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Using the graphic of the function matrix to locate
a function description . . . . . . . . . . . . . . . . . . . . . . . 5
1.3 Using the index of the function matrix to locate
a function description . . . . . . . . . . . . . . . . . . . . . . . 5
2 Function matrix . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 General layout of the function matrix . . . . . . . . . . . 6
2.1.1 Blocks (A, B, C, etc.) . . . . . . . . . . . . . . . . . . 6
2.1.2 Groups (AAA, AEA, CAA, etc.) . . . . . . . . . . 6
2.1.3 Function groups (000, 020, 060, etc.) . . . . . 6
2.1.4 Functions (0000, 0001, 0002, etc.) . . . . . . . 6
2.1.5 Codes identifying cells . . . . . . . . . . . . . . . . . 7
2.2 Function matrix Proline Promass 83 . . . . . . . . . . . . 8
3 Block MEASURED VARIABLES . . . . . . . . . 9
3.1 Group MEASURING VALUES . . . . . . . . . . . . . . . . 10
3.1.1 Function group MAIN VALUES . . . . . . . . . 10
3.1.2 Function group ADDITIONAL VALUES . . 11
3.2 Group SYSTEM UNITS . . . . . . . . . . . . . . . . . . . . . 14
3.2.1 Function group CONFIGURATION . . . . . . 14
3.2.2 Function group
ADDITIONAL CONFIGURATION . . . . . . . 17
4 Block QUICK SETUP . . . . . . . . . . . . . . . . . . 19
4.1 Quick Setup "Commissioning" . . . . . . . . . . . . . . . . 20
4.2 Quick Setup "Gas Measurement" . . . . . . . . . . . . . . 21
5 Block USER INTERFACE . . . . . . . . . . . . . . 22
5.1 Group CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.1.1 Function group BASIC CONFIGURATION 23
5.1.2 Function group UNLOCKING/LOCKING . 24
5.1.3 Function group OPERATION . . . . . . . . . . . 26
5.2 Group MAIN LINE . . . . . . . . . . . . . . . . . . . . . . . . 27
5.2.1 Function group CONFIGURATION . . . . . . 27
5.2.2 Function group MULTIPLEX . . . . . . . . . . . 29
5.3 Group ADDITION LINE . . . . . . . . . . . . . . . . . . . . 31
5.3.1 Function group CONFIGURATION . . . . . . 31
5.3.2 Function group MULTIPLEX . . . . . . . . . . . 34
5.4 Group INFORMATION LINE . . . . . . . . . . . . . . . . 37
5.4.1 Function group CONFIGURATION . . . . . . 37
5.4.2 Function group MULTIPLEX . . . . . . . . . . . 40
6 Block TOTALIZER . . . . . . . . . . . . . . . . . . . . . 43
6.1 Group TOTALIZERS (1 to 3) . . . . . . . . . . . . . . . . . 44
6.1.1 Function group CONFIGURATION . . . . . . 44
6.1.2 Function group OPERATION . . . . . . . . . . . 46
6.2 Group HANDLING TOTALIZER . . . . . . . . . . . . . . 47
7 Block BASIC FUNCTION . . . . . . . . . . . . . 48
7.1 Group FOUNDATION FIELDBUS . . . . . . . . . . . . . 49
7.1.1 Function group CONFIGURATION . . . . . . 49
7.1.2 Function group FUNCTION BLOCKS . . . . 50
7.1.3 Function group INFORMATION . . . . . . . . 51
7.2 Group PROCESS PARAMETER . . . . . . . . . . . . . . . 52
7.2.1 Function group CONFIGURATION . . . . . . 52
7.2.2 Function group EPD PARAMETER . . . . . . . 54
7.2.3 Function group REFERENCE PARAMETER 55
7.2.4 Function group ADJUSTMENT . . . . . . . . . 57
7.2.5 Function group PRESSURE CORRECTION 59
7.3 Group SYSTEM PARAMETER . . . . . . . . . . . . . . . . 60
7.3.1 Function group CONFIGURATION . . . . . . 60
7.4 Group SENSOR DATA . . . . . . . . . . . . . . . . . . . . . . 61
7.4.1 Function group CONFIGURATION . . . . . . 61
7.4.2 Function group FLOW COEFFICIENT . . . . 62
7.4.3 Function group DENSITY COEFFICIENT . . 63
7.4.4 Function group
ADDITIONAL COEFFICIENT . . . . . . . . . . 64
8 Block SPECIAL FUNCTION . . . . . . . . . . 65
8.1 Group DENSITY FUNCTIONS . . . . . . . . . . . . . . . . 66
8.1.1 Function group CONFIGURATION . . . . . . 66
8.2 Group ADVANCED DIAGNOSTICS . . . . . . . . . . . 72
8.2.1 Function group CONFIGURATION . . . . . . 72
8.2.2 Function group ACQUISITION . . . . . . . . . 73
8.2.3 Function group MASS FLOW . . . . . . . . . . . 74
8.2.4 Function group DENSITY . . . . . . . . . . . . . . 75
8.2.5 Function group REFERENCE DENSITY . . . 76
8.2.6 Function group TEMPERATURE . . . . . . . . 77
8.2.7 Function group TUBE DAMPING . . . . . . . 78
8.2.8 Function group
ELECTRODYNAMIC SENSORS . . . . . . . . . 79
8.2.9 Function group OPERATING
FREQUENCY FLUCTUATION . . . . . . . . . . 80
8.2.10 Function group TUBE
DAMPING FLUCTUATION . . . . . . . . . . . . 81
9 Block SUPERVISION . . . . . . . . . . . . . . . . . 83
9.1 Group SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
9.1.1 Function group CONFIGURATION . . . . . . 84
9.1.2 Function group OPERATION . . . . . . . . . . . 85
9.2 Group VERSION INFO . . . . . . . . . . . . . . . . . . . . . 87
9.2.1 Function group DEVICE . . . . . . . . . . . . . . 87
9.2.2 Function group SENSOR . . . . . . . . . . . . . . 87
9.2.3 Function group AMPLIFIER . . . . . . . . . . . . 88
9.2.4 Function group F-CHIP . . . . . . . . . . . . . . . 88
9.2.5 Function group I/O MODULE . . . . . . . . . . 89

Table of contents for local operation Device Functions Proline Promass 83 FOUNDATION Fieldbus
4Endress+Hauser
10 Factory settings . . . . . . . . . . . . . . . . . . . . . . . 90
10.1 SI units (not for USA and Canada) . . . . . . . . . . . . . 90
10.1.1 Low flow cut off, full scale value,
pulse value . . . . . . . . . . . . . . . . . . . . . . . . 90
10.1.2 Language . . . . . . . . . . . . . . . . . . . . . . . . 90
10.1.3 Density, length, temperature . . . . . . . . . . 91
10.2 US units (only for USA and Canada) . . . . . . . . . . . 91
10.2.1 Low flow cut off, full scale value,
pulse value . . . . . . . . . . . . . . . . . . . . . . . . 91
10.2.2 Language, density, length, temperature . . . 91
11 Index Function matrix . . . . . . . . . . . . . . . . 93
12 Index local operation . . . . . . . . . . . . . . . . . 97
Operation with FOUNDATION Fieldbus . 103

Device Functions Proline Promass 83 FOUNDATION Fieldbus 1 Notes on using this manual
Endress+Hauser 5
1 Notes on using this manual
There are various ways of locating the description of a function of your choice in the manual:
1.1 Using the table of contents to locate a function
description
The designations of all the cells in the function matrix are listed in the table of contents. You can
use these unambiguous designations (such as MEASURED VARIABLES, USER INTERFACE,
TOTALIZER, etc.) to choose whichever functions are applicable to a particular set of conditions.
The page references show you exactly where to find the detailed descriptions of the functions in
question. The table of contents is on page 3.
1.2 Using the graphic of the function matrix to locate a
function description
This step-by-step, top-down approach starts with the blocks, the highest level, and factory down
through the matrix to the description of the function you need:
1. All available blocks and their corresponding subgroups are shown on page 8. Select the block
(or the group within the block) which you need for your application and use the page reference
to locate the information corresponding to the next level.
2. The page in question contains a graphic showing of the block with all its subordinate groups,
function groups and functions. Select the function which you need for your application and use
the page reference to locate the detailed function description.
1.3 Using the index of the function matrix to locate a
function description
Each "cell" in the function matrix (blocks, groups, function groups, functions) has a unique identifier
in the form of a code consisting of one or three letters or a three- or four-digit number. The code
identifying a selected "cell" appears at the top right on the local display.
Example:
A0004750
The function matrix index lists the codes for all the available "cells" in alphabetic and consecutive
order, complete with the page references for the corresponding functions. The index to the function
matrix is on page 93.

2 Function matrix Device Functions Proline Promass 83 FOUNDATION Fieldbus
6Endress+Hauser
2 Function matrix
2.1 General layout of the function matrix
The function matrix consists of four levels:
Blocks →Groups →Function groups →Functions
A0000961
2.1.1 Blocks (A, B, C, etc.)
The blocks are the highest-level grouping of the operation options for the device. The blocks include,
for example: MEASURED VARIABLES, QUICK SETUP, USER INTERFACE, TOTALIZER, etc.
2.1.2 Groups (AAA, AEA, CAA, etc.)
A block consists of one or more groups. Each group represents a more detailed selection of the
operation options in the higher-order block. The groups in the "USER INTERFACE" block, for
example, include: CONTROL, MAIN LINE, ADDITION LINE, etc.
2.1.3 Function groups (000, 020, 060, etc.)
A group consists of one or more function groups. Each function group represents a more detailed
selection of the operation options in the higher-order group. The function groups in the CONTROL
group, for example, include: BASIC CONFIGURATION, UN-/LOCKING, OPERATION, etc.
2.1.4 Functions (0000, 0001, 0002, etc.)
Each function group consists of one or more functions. The functions are used to operate and
parameterize the device. Numerical values can be entered or parameters selected and saved.
The functions in the BASIC CONFIGURATION function group include LANGUAGE, DISPLAY
DAMPING, CONTRAST LCD, etc.
The procedure for changing the language of the user interface, for example, is as follows:
1. Select the USER INTERFACE block
2. Select the CONTROL group
3. Select the BASIC CONFIGURATION function group
4. Select the LANGUAGE function (this is where the language can be selected).
…
…
…
…
…
…
…
…
0001
2001
0401
2021
2201
0002
2002
0402
2022
2202
0003
2003
0403
2023
2203
0009
2009
0409
2029
2209
0429
2049
2069
0421
2041
0422
2042
0423
2043
20632061 2062
0000
2000
0400
2020
2200
0420
2040
2060
000
200
040
202
220
042
204
206
AAA
BAA
ACA
CAA
CBA
D, E, …
A
B
C

Device Functions Proline Promass 83 FOUNDATION Fieldbus 2 Function matrix
Endress+Hauser 7
2.1.5 Codes identifying cells
Each cell (block, group, function group and function) in the function matrix has an individual,
unique code.
Blocks:
The code is a letter (A, B, C, etc.)
Groups:
The code consists of three letters (AAA, ABA, BAA, etc.).
The first letter matches the block code (i.e. each group in block A has a code starting with an "A",
in other words A _ _; the codes of the groups in block B start with a "B", in other words B_ _ , and
so on). The other two letters are for identifying the group within the respective block.
Function groups:
The code consists of three digits (000, 001, 100, etc.)
Functions:
The code consists of four digits (0000, 0001, 0201, etc.).
The first three digits are the same as the code for the function group. The last digit in the code is a
counter for the functions in the function group, incrementing from 0 to 9 (e.g. function 0005 is the
sixth function in group 000).
A0001251
Block Group Function group Functions
200020012002200
CAAC

2 Function matrix Device Functions Proline Promass 83 FOUNDATION Fieldbus
8Endress+Hauser
2.2 Function matrix Proline Promass 83
BLOCKS GROUPS FUNCTION
GROUPS
MEASURED VARIABLES A→MEASURING VALUES AAA →page 10
( → Page 9) SYSTEM UNITS ACA →page 14
↓SPECIAL UNITS AEA →page 14
QUICK SETUP B→Commissioning and application setups →page 83
( → Page 9)
↓
USER INTERFACE C→CONTROL CAA →page 23
( → Page 22) MAIN LINE CCA →page 27
↓ADDITION LINE CEA →page 31
INFORMATION LINE CGA →page 37
TOTALIZER D→TOTALIZERS (1 to 3) DAA,
-B, -C →page 44
( → Page 43) HANDLING TOTALIZER DJA →page 47
↓
BASIC FUNCTION G→FOUNDATION FIELDBUS GGA →page 49
( → Page 48) PROCESS PARAMETER GIA →page 52
↓SYSTEM PARAMETER GLA →page 60
SENSOR DATA GNA →page 61
SPECIAL FUNCTION H→DENSITY FUNCTIONS HAA →page 66
( → Page 65) ADVANCED DIAGNOSTICS HEA →page 72
↓
SUPERVISION J→SYSTEM JAA →page 84
( → Page 83) VERSION INFO JCA →page 87

Device Functions Proline Promass 83 FOUNDATION Fieldbus 3 Block MEASURED VARIABLES
Endress+Hauser 9
3 Block MEASURED VARIABLES
Functions
COR.
CARR.V.FL
(0029) P. 13
% CARR.
VOL. FL.
(0028) P. 12
CARR.
VOL.FLOW
(0027) P. 12
% CARR.
MASS FL
(0026) P. 12
TEMPERATURE
(0008) P. 10
CARR.
MASS FLOW
(0025) P. 12
° BRIX
(0036) P. 13
UNIT
COR. VOLUME
(0405) P. 16
REFERENCE
DENSITY
(0006) P. 10
COR.
TARG.V.FL.
(0024) P. 12
° BALLING
(0035) P. 13
UNIT
COR.VOL.FL.
(0404) P. 16
UNIT
PRESSURE (0426)
P. 18
DENSITY
(0005) P. 10
% TARG.
VOL. FL.
(0023) P. 11
° PLATO
(0034) P. 13
UNIT VOLUME
(0403) P. 15
UNIT
LENGTH
(0424) P. 18
COR.
VOLUME FLOW
(0004) P. 10
TARG.
VOL.FLOW
(0022) P. 11
° API
(0033) P. 13
UNIT
VOL. FLOW
(0402) P. 15
UNIT
TEMPERATURE
(0422) P. 17
VOLUME FLOW
(0001) P. 10
% TARG.
MASS FL.
(0021) P. 11
° BAUME
(0031) P. 13
UNIT
MASS (0401)
P. 14
UNIT
REF. DENSITY
(0421) P. 17
⇒ ⇒ ⇒ ⇒ ⇒
MASS FLOW
(0000) P. 10
TARG.
MASS FLOW
(0020) P. 11
%-BLACK
LIQUOR
(0030) P. 13
UNIT
MASS FLOW
(0400) P. 14
UNIT DENSITY
(0420) P. 17
⇒ ⇒ ⇒ ⇒
Function
groups
MAIN VALUES
(000) P. 10
ADDITIONAL
VALUES
(002) P. 11
CONFIGURATION
(040) P. 14
⇓ ⇑
ADD.
CONFIGURATION
(042) P. 17
⇒ ⇒
Groups
MEASURING
VALUES
(AAA) P. 10
⇓ ⇑
SYSTEM
UNITS
(ACA) P. 14
⇒
Block
MEASURED
VARIABLES
(A)

3 Block MEASURED VARIABLES Device Functions Proline Promass 83 FOUNDATION Fieldbus
10 Endress+Hauser
3.1 Group MEASURING VALUES
3.1.1 Function group MAIN VALUES
MEASURED
VARIABLES A⇒MEASURING VALUES AAA ⇒MAIN VALUES 000
Function description
MEASURED VARIABLES →MEASURING VALUES →MAIN VALUES
!Note!
• The engineering units of all the measured variables shown here can be set in the SYSTEM UNITS group.
• If the fluid in the pipe flows backwards, a negative sign prefixes the flow reading on the display.
MASS FLOW
(0000)
The currently measured mass flow appears on the display.
Display:
5-digit floating-point number, including unit and sign
(e.g. 462.87 kg/h; –731.63 lb/min; etc.)
VOLUME FLOW
(0001)
The calculated volume flow appears on the display. The volume flow is derived from
the measured mass flow and the measured density of the fluid.
Display:
5-digit floating-point number, including unit and sign
(e.g. . 5.5445 dm3/min; 1.4359 m3/h; –731.63 gal/d; etc.)
CORRECTED VOLUME
FLOW (0004)
The calculated corrected volume flow appears on the display. The calculated
corrected volume flow is derived from the measured mass flow and the reference
density of the fluid (density at reference temperature, measured or fixed entry).
Display:
5-digit floating-point number, including unit and sign
(e.g. 1.3549 Nm3/h; 7.9846 scm/day; etc.)
DENSITY
(0005)
The currently measured density or its specific gravity appears on the display.
Display:
5-digit floating point number, including unit
(e.g. 1.2345 kg/dm3; 993.5 kg/m3; 1.0015 SG_20 °C; etc.)
REFERENCE DENSITY
(0006)
The density of the fluid, at reference temperature, appears on the display. The
reference density can be calculated with the measured density or specified by means
of the FIXED REF. DENSITY function (6461).
Display:
5-digit floating point number, including unit
(e.g. 1.2345 kg/dm3; 993.5 kg/m3; 1.0015 SG_20 °C; etc.)
TEMPERATURE
(0008)
The currently measured temperature appears on the display.
Display:
Max. 4-digit fixed-point number, including unit and sign
(e.g. –23.4 °C; 160.0 °F; 295.4 K; etc.)

Device Functions Proline Promass 83 FOUNDATION Fieldbus 3 Block MEASURED VARIABLES
Endress+Hauser 11
3.1.2 Function group ADDITIONAL VALUES
MEASURED
VARIABLES A⇒MEASURING VALUES AAA ⇒MAIN VALUES 000
⇓
ADDITIONAL VALUES 002
Function description
MEASURED VARIABLES →MEASURING VALUES →ADDITIONAL VALUES
TARGET
MASS FLOW
(0020)
!Note!
This function is not available unless one of the following was selected:
• In the DENSITY FUNCTION function (7000):
– % MASS / % VOLUME
– FLEXIBLE and in the MODE function (7021) the option % MASS 2D or % MASS 3D.
Use this function to display the currently measured mass flow of the target fluid.
Target fluid = carried material (e.g. lime powder).
Display:
5-digit floating-point number, including unit and sign
% TARGET
MASS FLOW
(0021)
!Note!
This function is not available unless one of the following was selected:
• In the DENSITY FUNCTION function (7000):
– % MASS / % VOLUME
– FLEXIBLE and in the MODE function (7021) the option % MASS 2D or % MASS 3D.
In this function, the currently measured mass flow of the target fluid is displayed as a %
(of the overall mass flow). Target fluid = carried material (e.g. lime powder).
Display:
5-digit floating-point number, including unit and sign
TARGET
VOLUME FLOW
(0022)
!Note!
This function is not available unless one of the following was selected:
• In the DENSITY FUNCTION function (7000):
– % MASS / % VOLUME
– FLEXIBLE and in the MODE function (7010) the option % VOLUME 2D or
% VOLUME 3D.
In this function, the currently measured volume flow of the target fluid is displayed.
Target fluid = carried material (e.g. lime powder).
Display:
5-digit floating-point number, including unit and sign
% TARGET
VOLUME FLOW
(0023)
!Note!
This function is not available unless one of the following was selected:
• In the DENSITY FUNCTION function (7000):
– % MASS / % VOLUME
– FLEXIBLE and in the MODE function (7010) the option % VOLUME 2D or
% VOLUME 3D.
Use this function to display the currently measured volume flow of the target fluid as a %
(of the overall volume flow). Target fluid = carried material (e.g. lime powder).
Display:
5-digit floating-point number, including unit and sign

3 Block MEASURED VARIABLES Device Functions Proline Promass 83 FOUNDATION Fieldbus
12 Endress+Hauser
CORRECTED
TARGET VOLUME FLOW
(0024)
!Note!
This function is not available unless % MASS / % VOLUME was selected in the
DENSITY FUNCTION function (7000).
Use this function to display the currently measured corrected volume flow of the target
fluid. Target fluid = carried material (e.g. lime powder).
Display:
5-digit floating-point number, including unit and sign
CARRIER
MASS FLOW
(0025)
!Note!
This function is not available unless one of the following was selected:
• In the DENSITY FUNCTION function (7000):
– % MASS / % VOLUME
– FLEXIBLE and in the MODE function (7021) the option % MASS 2D or % MASS 3D.
Use this function to display the currently measured mass flow of the carrier fluid.
Carrier fluid = transporting liquid (e.g. water).
Display:
5-digit floating-point number, including unit and sign
% CARRIER
MASS FLOW
(0026)
!Note!
This function is not available unless one of the following was selected:
• In the DENSITY FUNCTION function (7000):
– % MASS / % VOLUME
– FLEXIBLE and in the MODE function (7021) the option % MASS 2D or % MASS 3D.
Use this function to display the currently measured mass flow of the carrier fluid as a %
(of the overall mass flow). Carrier fluid = transporting liquid (e.g. water).
Display:
5-digit floating-point number, including unit and sign
CARRIER
VOLUME FLOW
(0027)
!Note!
This function is not available unless one of the following was selected:
• In the DENSITY FUNCTION function (7000):
– % MASS / % VOLUME
– FLEXIBLE and in the MODE function (7021) the option % VOLUME 2D or
% VOLUME 3D.
Use this function to display the currently measured volume flow of the carrier fluid.
Carrier fluid = transporting liquid (e.g. water).
Display:
5-digit floating-point number, including unit and sign
% CARRIER
VOLUME FLOW
(0028)
!Note!
This function is not available unless one of the following was selected:
• In the DENSITY FUNCTION function (7000):
– % MASS / % VOLUME
– FLEXIBLE and in the MODE function (7021) the option % VOLUME 2D or
% VOLUME 3D.
Use this function to display the currently measured volume flow of the carrier fluid as a %
(of the overall mass flow). Carrier fluid = transporting liquid (e.g. water).
Display:
5-digit floating-point number, including unit and sign
Function description
MEASURED VARIABLES →MEASURING VALUES →ADDITIONAL VALUES

Device Functions Proline Promass 83 FOUNDATION Fieldbus 3 Block MEASURED VARIABLES
Endress+Hauser 13
CORRECTED CARRIER
VOLUME FLOW
(0029)
!Note!
This function is not available unless % MASS / % VOLUME was selected in the
DENSITY FUNCTION function (7000).
Use this function to display the currently measured corrected volume flow of the carrier
fluid. Carrier fluid = transporting liquid (e.g. water).
Display:
5-digit floating-point number, including unit and sign
%-BLACK LIQUOR
(0030) !Note!
This function is not available unless %-BLACK LIQUOR was selected in the
DENSITY FUNCTION function (7000).
The concentration in %-BLACK LIQUOR is displayed.
Display:
5-digit floating-point number, incl. units
° BAUME
(0031) !Note!
This function is not available unless °BAUME was selected in the DENSITY FUNCTION
function (7000).
The concentration in °BAUME is displayed.
Display:
5-digit floating-point number, incl. units
° API
(0033) !Note!
This function is not available unless °API was selected in the DENSITY FUNCTION
function (7000).
The concentration in °API is displayed.
Display:
5-digit floating-point number, incl. units
° PLATO
(0034) !Note!
This function is not available unless °PLATO was selected in the DENSITY FUNCTION
function (7000).
The concentration in °PLATO is displayed.
Display:
5-digit floating-point number, incl. units
° BALLING
(0035) !Note!
This function is not available unless °BALLING was selected in the DENSITY FUNCTION
function (7000).
The concentration in °BALLING is displayed.
Display:
5-digit floating-point number, incl. units
° BRIX
(0036) !Note!
This function is not available unless °BRIX was selected in the DENSITY FUNCTION
function (7000).
The concentration in °BRIX is displayed.
Display:
5-digit floating-point number, incl. units
Function description
MEASURED VARIABLES →MEASURING VALUES →ADDITIONAL VALUES

3 Block MEASURED VARIABLES Device Functions Proline Promass 83 FOUNDATION Fieldbus
14 Endress+Hauser
3.2 Group SYSTEM UNITS
3.2.1 Function group CONFIGURATION
MEASURED
VARIABLES A⇒MEASURING VALUES AAA
⇓
SYSTEM UNITS ACA ⇒CONFIGURATION 040
Function description
MEASURED VARIABLES →SYSTEM UNITS →CONFIGURATION
You can select the units for measured variables in this function group.
!Note!
The units selected here have no effect on the fieldbus. They are only used for the local display and for assigned
instrument functions.
UNIT MASS FLOW
(0400)
Use this function to select the unit for displaying the mass flow (mass/time).
The unit you select here is also valid for:
• Switching points (limit value for mass flow, flow direction)
• Low flow cut off
Options:
Metric:
Gram →g/s; g/min; g/h; g/day
Kilogram →kg/s; kg/min; kg/h; kg/day
Ton →t/s; t/min; t/h; t/day
US:
Ounce →oz/s; oz/min; oz/h; oz/day
Pound →lb/s; lb/min; lb/h; lb/day
Ton →ton/s; ton/min; ton/h; ton/day
Factory setting:
Depends on country (kg/h or US-lb/min)
UNIT MASS
(0401)
Use this function to select the unit for displaying the mass.
The unit you select here is also valid for:
• Pulse weighting (e.g. kg/p)
Options:
Metric →g; kg; t
US →oz; lb; ton
Factory setting:
Depends on country (kg or US-lb)
!Note!
The unit of the totalizers is independent of your choice here. The unit for each totalizer
is selected separately for the totalizer in question.

Device Functions Proline Promass 83 FOUNDATION Fieldbus 3 Block MEASURED VARIABLES
Endress+Hauser 15
UNIT VOLUME FLOW
(0402)
Use this function to select the unit for displaying the volume flow (volume/time).
The unit you select here is also valid for:
• Switching points (limit value for volume flow, flow direction)
• Low flow cut off
Options:
Metric:
Cubic centimeter →cm3/s; cm3/min; cm3/h; cm3/day
Cubic decimeter →dm3/s; dm3/min; dm3/h; dm3/day
Cubic meter →m3/s; m3/min; m3/h; m3/day
Milliliter →ml/s; ml/min; ml/h; ml/day
Liter →l/s; l/min; l/h; l/day
Hectoliter →hl/s; hl/min; hl/h; hl/day
Megaliter →Ml/s; Ml/min; Ml/h; Ml/day
US:
Cubic centimeter →cc/s; cc/min; cc/h; cc/day
Acre foot →af/s; af/min; af/h; af/day
Cubic foot →ft3/s; ft3/min; ft3/h; ft3/day
Fluid ounce →oz f/s; oz f/min; oz f/h; oz f/day
Gallon →gal/s; gal/min; gal/h; gal/day
Kilo gallon →Kgal/s; Kgal/min; Kgal/h; Kgal/day
Million gallon →Mgal/s; Mgal/min; Mgal/h; Mgal/day
Barrel (normal fluids: 31.5 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
Barrel (beer: 31.0 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
Barrel (petrochemicals: 42.0 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
Barrel (filling tanks: 55.0 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
Imperial:
Gallon →gal/s; gal/min; gal/h; gal/day
Mega gallon →Mgal/s; Mgal/min; Mgal/h; Mgal/day
Barrel (beer: 36.0 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
Barrel (petrochemicals: 34.97 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
Factory setting:
Depends on country (m3/h or US-Mgal/day)
UNIT VOLUME
(0403)
Use this function to select the unit for displaying the volume.
The unit you select here is also valid for:
• Pulse weighting (e.g. m3/p)
Options:
Metric →cm3; dm3; m3; ml; l; hl; Ml Mega
US →cc; af; ft3; oz f; gal; Kgal; Mgal; bbl (normal fluids); bbl (beer);
bbl (petrochemicals); bbl (filling tanks)
Imperial →gal; Mgal; bbl (beer); bbl (petrochemicals)
Factory setting:
m3
!Note!
The unit of the totalizers is independent of your choice here. The unit for each totalizer
is selected separately for the totalizer in question.
Function description
MEASURED VARIABLES →SYSTEM UNITS →CONFIGURATION

3 Block MEASURED VARIABLES Device Functions Proline Promass 83 FOUNDATION Fieldbus
16 Endress+Hauser
UNIT CORRECTED
VOLUME FLOW
(0404)
Use this function to select the unit for displaying the corrected volume flow
(corrected volume/time).
The unit you select here is also valid for:
• Switching points (limit value for corrected volume flow, flow direction)
• Low flow cut off
Options:
Metric → Nl/s; Nl/min; Nl/h; Nl/day; Nm3/s; Nm3/min; Nm3/h; Nm3/day
US →Sm3/s; Sm3/min; Sm3/h; Sm3/day; Scf/s; Scf/min; Scf/h; Scf/day
Factory setting:
Nm3/h
UNIT CORRECTED
VOLUME
(0405)
Use this function to select the unit for displaying the corrected volume.
The unit you select here is also valid for:
• Pulse weighting (e.g. Nm3/p)
Options:
Metric →Nm3; Nl
US →Sm3; Scf
Factory setting:
Nm3
!Note!
The unit of the totalizers is independent of your choice here. The unit for each totalizer
is selected separately for the totalizer in question.
Function description
MEASURED VARIABLES →SYSTEM UNITS →CONFIGURATION

Device Functions Proline Promass 83 FOUNDATION Fieldbus 3 Block MEASURED VARIABLES
Endress+Hauser 17
3.2.2 Function group ADDITIONAL CONFIGURATION
MEASURED
VARIABLES A⇒MEASURING VALUES AAA
⇓
SYSTEM UNITS ACA ⇒CONFIGURATION 040
⇓
ADD. CONFIGURATION 042
Function description
MEASURED VARIABLES →SYSTEM UNITS →ADDITIONAL CONFIGURATION
!Note!
The units selected here have no effect on the fieldbus. They are only used for the local display and for assigned
instrument functions.
UNIT DENSITY
(0420)
Use this function to select the unit for displaying the fluid density.
The unit you select here is also valid for:
• Switching points (limit value for density)
• Density response value for EPD
• Density adjustment value
Options:
Metric →g/cm3; g/cc; kg/dm3; kg/l; kg/m3; SD 4 °C, SD 15 °C, SD 20 °C;
SG 4 °C, SG 15 °C, SG 20 °C
US →lb/ft3; lb/gal; lb/bbl (normal fluids); lb/bbl (beer);
lb/bbl (petrochemicals); lb/bbl (filling tanks)
Imperial →lb/gal; lb/bbl (beer); lb/bbl (petrochemicals)
Factory setting:
kg/l
SD = Specific Density, SG = Specific Gravity
The specific density is the ratio of fluid density to water density (at water temperature =
4, 15, 20 °C).
UNIT REFERENCE
DENSITY
(0421)
Use this function to select the unit for displaying the reference density.
The unit you select here is also valid for:
• Switching points (limit value for density)
• Fixed reference density (for calculation of corrected volume flow)
Options:
Metric →kg/Nm3; kg/Nl
US → g/Scc; kg/Sm3; lb/Scf
Factory setting:
kg/Nl
UNIT TEMPERATURE
(0422)
Use this function to select the unit for displaying the temperature.
The unit you select here is also valid for:
• Switching points (limit value for temperature)
• Reference temperature (for corrected volume measurement with
measured reference density)
Options:
°C (Celsius)
K (Kelvin)
°F (Fahrenheit)
R (Rankine)
Factory setting:
°C

3 Block MEASURED VARIABLES Device Functions Proline Promass 83 FOUNDATION Fieldbus
18 Endress+Hauser
UNIT LENGTH
(0424)
Use this function to select the unit for displaying the length of the nominal diameter.
The unit you select here is valid for:
• Nominal diameter of the sensor (→NOMINAL DIAMETER function (6804))
Options:
MILLIMETER
INCH
Factory setting:
MILLIMETER
UNIT PRESSURE
(0426)
Use this function to select the unit for pressure.
The unit you select here is valid for:
• Specified pressure (→PRESSURE function (6501))
Options:
bar a
bar g
psi a
psi g
Factory setting:
bar g
Function description
MEASURED VARIABLES →SYSTEM UNITS →ADDITIONAL CONFIGURATION

Device Functions Proline Promass 83 FOUNDATION Fieldbus 4 Block QUICK SETUP
Endress+Hauser 19
4 Block QUICK SETUP
Block Group Function
groups Functions
QUICK SETUP
(B)
⇒⇒
QS COMMISS.
(1002) P. 19 ⇒
QS-GAS
MEASURE
(1004) P. 19
T-DAT
SAVE/LOAD
(1009) P. 19
Function description
QUICK SETUP
QUICK SETUP
COMMISSIONING
(1002)
Use this function to start the Setup menu for commissioning.
Options:
YES
NO
Factory setting:
NO
!Note!
You will find a flowchart of the COMMISSIONING setup menu on page 20.
For more information on Setup menus, please refer to the Operating Instructions for
Proline Promass 83, BA065D/06/en.
QUICK SETUP GAS
MEASUREMENT
(1004)
Use this function to start the application-specific Setup menu for the gas measurement.
Options:
YES
NO
Factory setting:
NO
!Note!
You will find a flowchart of the GAS MEASUREMENT setup menu on page 21. For more
information on Setup menus, please refer to the Operating Instructions Proline Promass 83,
BA065D/06/en.
T-DAT SAVE/LOAD
(1009)
Use this function to save the parameter settings / configuration of the transmitter in a
transmitter DAT (T-DAT), or to load the parameter settings from the T-DAT into the
EEPROM (manual safety function).
Application examples:
• After commissioning, the current measuring point parameters can be saved to the
T–DAT as a backup.
• If the transmitter is replaced for some reason, the data from the T-DAT can be loaded
into the new transmitter (EEPROM).
Options:
CANCEL
SAVE (from EEPROM to T-DAT)
LOAD (from the T-DAT into EEPROM)
Factory setting:
CANCEL
!Note!
• If the target device has an older software version, the message "TRANSM.SW–DAT"
is displayed during startup. Then only the SAVE function is available.
•LOAD
This option is only possible if the target device has the same software version as,
or a more recent software version than, the source device.
•SAVE
This option is always available.

4 Block QUICK SETUP Device Functions Proline Promass 83 FOUNDATION Fieldbus
20 Endress+Hauser
4.1 Quick Setup "Commissioning"
A0004740-en
!Note!
• The display returns to the cell QUICK SETUP COMMISSIONING (1002) if you press the Xkey
combination during parameter interrogation. The stored parameters remain valid.
• The system units selected via the Quick Setup are only valid for displaying on the local display
and for parameters in the Transducer Blocks. They have no effect on the process variables which
are transmitted via the FOUNDATION Fieldbus.
mSelecting DELIVERY SETTINGS returns each selected unit to the factory setting.
Selecting ACTUAL SETTING applies the units you have set previously.
nOnly units not yet configured in the current Setup are offered for selection in each cycle. The unit for mass,
volume and corrected volume is derived from the corresponding flow unit.
oThe YES option remains visible until all the units have been configured.
NO is the only option displayed when no further units are available.
pThe "automatic parameterization of the display" option contains the following basic settings/
factory settings:
YES Main line = Mass flow
Additional line = Totalizer 1
Information line = Operating/system condition
NO The existing (selected) settings remain.
6461
0421 6462
6463
6464
2000
1002
B
+
++
EE
Esc
E
+
-
XXX.XXX.XX
HOME-POSITION
0402 04040400 0420 0422
3001 6460
3001
1004
m
n
o
p
Yes
Yes
No
No
No
Reference Calculated
Fix. Density
Density
Unit
Ref. Density Exp. Coeff. Lin
Exp. Coeff. SQR
Reference temp.
Volume flow Corr. Vol. flow Mass flow Density Temperature Quit
Unit
Volume flow Unit
Corr. Vol. flow
Unit
Mass flow Unit
Density Unit
Temperature
Unit
Totalizer Corr. Vol.
calculation
Unit
Totalizer
Language
Pre-setting
Quick Setup QS
Commission
Gas
measurement
Selection pre-settings Actual SettingsDeliver Settingsy
Selection
System units
Automatic parameterization
of the display
Carrying out the selected
Quick Setup Quick Setup
complete
Autom. Configuration
of Display?
Another
Quick Setup?