cubiio PL-01B LM Guide

Never attempt to turn on or operate laser module
before reading, understanding and fully familiarizing
yourself with the contents of replacement instructions.
PL-01B LM
Laser Module Replacement Instructions
MADE IN TAIWAN

Before Replacing
Only person with specialized training and appropriate
laser safety knowledge can maintain the laser
module. The laser module operator must be aware of
laser radiation hazard.
Read all of section 1: Warning and Cautionary Messages
and section 2: Safety and Regulatory Information in the
PL-01B User’s manual and keep these sections for later
use.
The laser module must be properly mounted to
CubiioShield such that it cannot be moved unintention-
ally.
Keep laser module out of children’s and teenagers’
reach.
The module emits Class 4 laser radiation. EXPOSURE TO
THE LASER MATERIAL PROCESSING BEAM CAN RESULT
IN BURNS TO THE SKIN AND CAN CAUSE SEVERE EYE
DAMAGE. Proper use and care of laser module are essen-
tial to safe operation.

Step3.
Step1.
T10H
Step2.
Replacement Steps
Validation of Laser Module
1. Loosen the star screw by a "T10H" screwdriver or a
2.4mm flat-head screwdriver.
2. Loosen the UNC 1/4" screw by a coin or a flat-head
screwdriver.
3. Replace the laser module and fasten screws.
We will send you an email with a password-protected PDF
after your purchase has been shipped. Follow instructions
and steps to validate your laser module. If you have any
question, please email to [e-mail] for further
assistance.

1
2
3
4
5
6
7
1. Power key
2. Light indicator
3. Laser aperture
4. Laser label
5. Micro SD card slot
6. USB socket
7. 1/4″ screw mount
Laser Module Overview
Laser source Blue Laser, 450 nm
< 800 mW
100 × 100 mm
155 mm
50 × 50 × 50 mm
153 g
DC 5 V, 2 A via microUSB Type B
Micro SD card
BLE (Bluetooth Low Energy)
2402-2480 MHz
Hold your mobile device and
operate cubiio app at the distance
less than 1 m.
iOS 10+ / Android 4.4+
5 ℃- 40 ℃ (non-condensing)
5%- 80%
Stop 10 min after 1-hour
continuous operation.
Max. Laser Output
Working Area
Working Distance
Dimensions
Weight
Power Input
Data Storage
App Connection
Operating Temperature Range
App OS
Operating Humidity Range
Recommended Processing Time

在完全熟讀、理解本指引內容前
切勿嘗試開啟或操作雷射模組
PL-01B LM
雷射模組拆換指引
MADE IN TAIWAN

拆換之前
只有經過專業培訓且具有適當雷射安全知識的人才能操作
雷射模組。操作者必須注意雷射安全。
熟讀PL-01B用戶手冊中的1.警告與注意事項及2.法規遵循，
並妥善保存手冊以備日後使用。
雷射模組必須正確安裝在保護罩(CubiioShield)上，以免意
外移動。
請將雷射模組放置在小孩及未成年人無法接觸到的地方。
本模組使用第四級雷射源。暴露在雷射加工光束中，對皮膚
會發生燒傷之危險且會對眼睛產生嚴重的傷害。正確地使用
及維護本產品，對本產品的安全操作至關重要。

Step3.
Step1.
T10H
Step2.
拆換步驟
1. 用T10H的螺絲起子或2.4mm一字起鬆開側面的星型螺絲
2. 用一字起或硬幣退開後方的雲台螺絲
3. 替換雷射模組
*過程中請確保螺絲鬆開後再拿取雷射模組，勿蠻力拆下

1
2
3
4
5
6
7
雷射模組外觀
雷射源 450 nm 藍光雷射
< 800 mW
100 × 100 mm
155 mm
50 × 50 × 50 mm
153 g
DC 5 V, 2 A via microUSB Type B
Micro SD 記憶卡
BLE (Bluetooth Low Energy)
2402-2480 MHz
使用建議：手握行動裝置並距離1m
內進行產品連線操作
iOS 10+ / Android 4.4+
5 ℃ 至 40 ℃
5% 至 80%
連續加工1小時需休息10分鐘
最大輸出功率
工作範圍
工作距離
尺寸
重量
電源輸入
檔案傳輸
產品連線方式
工作溫度範圍
App OS
工作濕度範圍
建議加工時間
3. 雷射出光口
4. 雷射警語標示
1. 雷射電源開關
2. 指示燈
5. Micro SD卡插槽
6. USB插槽
7. 1/4″螺絲安裝孔