Cura1 2549 User manual

2549 Cordless Multiport Expander
with Bracket Mount
UM-044b
Optional 2406M
Plug Pack 6 Vdc
Optional 2638
Nurse Call Pendant
Do not immerse or wash pads or
mats under running water. Use a
damp cloth (1/1000 bleach solution)
& wipe clean. Dry all spills on mats
immediately.
All our products are supplied with a
full warranty and are guaranteed to
be free from defects in material and
workmanship
Do NOT fold pads or
mats when in transit
or storage.
Keep pads & mats
flat at all times
Call Cord
ON / OFF
Cord Removal
Alarm
Antenna
Program Button
If using optional
Nurse Call Pendant
set switch to ON
position else leave OFF.
Always leave switch in
ON position.
Reset Button
1. Will clear any fault conditions e.g.
Signal Lost or Low Battery
2. If no fault condition, then it will
activate a 3 minute delay.
Status LED will flash during the delay
and no alarms will be generated.
Pressing again before the 3 minutes
have elapsed will return the unit to
normal operation.
To Nurse
Call System.
Antenna
wire
Clip slides into
3504 Mounting
Bracket. 3504 Mounting
Bracket
Optional Accessories (Sold Seperately)
2406M Plug Pack 6V Power Adaptor
2558 Wireless Waterproof Call Button
2588 Personal Emergency Transmitter (PET)
2599 Wireless SOS Call Button
2638 Nurse Call Pendant
2719, 2720 Cordless & Universal Pad Transmitters
(& all Pads & Mats that use them).
2721 iBeam
3502 Wireless Handset
3503 Wireless Door Contact
3504 Mounting Bracket
Curly Cords 300mm R/A 6.35 Plug:
4160 (T & S), 4161 (T & R), 4162 (R & S)
Curly Cords 300mm R/A 3.5 Plug:
4163 (T & S), 4164 (T & R), 4165 (R & S)
Bottom View
Back View
Program
Nurse Call
DC 6V
0.5A
Side View
Top View
Reset
Error Status
Front
View
Error LED: Yellow Red
Flashes Expander Cordless Pad
1 Low Bat. Pad Low Bat.
2 Pad Signal Lost
Disconnect
3 AC Lost
Status LED: Green
Blinking Pad Active
ON Alarm Trigger
Error
Indicator
LED
Status
Indicator
LED
Error & Status Indicator
LED explanation.

QUICK START GUIDE
2549 Cordless Multiport Expander Bracket Mount
3
Step
Plug Multiport Expander into nurse call
system & test operation of all devices in
their final location.
Error Status
Test Multiport Expander prior to every use.
Cordless Floor
Mat is placed in
doorway or
beside the bed.
2588 Personal
Emergency
Transmitter
(PET)
Bed or Chair Pad
with Pad / Mat
Transmitter Insert.
ON OFF
Cordless Pad
or Mat
15 Seconds
A 2719/20 Pad / Mat transmitter which has been switched OFF
will be in Storage Mode when it is switched ON again. To
prevent a transmitter entering Storage Mode, activate it by
applying pressure to the Pad / Mat for 15 seconds after being
switched ON.
Plug into nurse
call system
Plug RJ12 end
of Curly Cord
into Multiport
Expander
2549 Cordless
Multiport
Expander with
Bracket Mount
1
Error Status
Insert 3 X AAA
alkaline batteries into
battery compartment.
Release screw
to open battery
compartment.
Error Status
Step
Insert 3 x AAA alkaline batteries into
battery compartment.
2
Step
Pair Multiport Expander with transmitter/s.
Transmitters can be a Cordless Bed / Chair Pad, Cordless Floor Mat,
Personal Emergency Transmitter (PET), iBeam, SOS Call Button,
Magnetic Door Switch, Waterproof Call Button or Wireless Handset.
1. Place transmitters to be paired within easy reach.
2549 Multiport Expanders are designed to work in a facility on
alkaline batteries equivalent to those originally supplied with the
device.
Operable alkaline batteries must be installed in the device at all
times during operation. Batteries must be removed from the
device while it’s in storage.
Use of an optional 2406M Plug Pack will extend the usable
battery life. Essentially a Plug Pack may not be required in
most instances.
2. Clear the program memory: Press & hold the Program
button until the Error & Status LEDs illuminate. Keep holding
down the Program button until the LEDs flash quickly, then
release.
3. Enter Program Mode: Press & hold the Program button on
the Multiport Expander until the Error & Status LEDs
illuminate. Now release the Program button.
4. Pair the first transmitter:
- For 2719 / 2720 Pad / Mat Transmitters: turn the transmitter
from OFF to ON. The Error LED will flash once to
acknowledge succesful pairing
- For all other transmitters: Activate the transmitter (trigger an
alarm). The Status LED will flash once to acknowledge
successful pairing.
After each successful pairing the Multiport Expander will exit
Program Mode and the Status and Error LEDs will go out.
5. Pair remaining transmitters: Repeat step 3 & 4 for each
transmitter to be paired. Up to 2 Cordless Pad / Mat
Transmitters and up to 3 other devices can be paired with
each Multiport Expander.
6. If 2719 / 2720 Transmitters are used then connect them to
a Cordless Pad or Mat & ensure that it is switched ON.
RJ12
Special Note When Testing Pad / Mats: