Cusam Cs-200zw-1 User manual

www.cusamintercom.com

0

VIDEO

INTERCOM

SYSTEM

FOR

APARTMENT

(NETWORK)

USER

’

S

MAUAL

QUZHOU

ZHUOCHENG

ELECTRONIC

CO.,LTD

www.cusamintercom.com

1

Contents

(Install

and

Using

Instruction)

1.Function Introduction------------------------------------------------ - ------------- -------- --- 3

2.Using Method------------------------------------------------------------ -- ------------- ------- - 3

3.System Schematic and Wiring Diagram---------------------------- - ---------- -------4-5

( 1 ) System structure schematic drawing ------------------------------------------------4

( 2 ) system wiring diagram ------------------------------------------------------------------5

4.Code Setting-------------------------------------------------------------------- - --- ------- -- 6-7

5.Table3.1 comparative table of initializ at ing the first building door station

number and Network switcher address----------------------------------- ----------- - 8-9

6.Table3.2 comparative table of initializating room number and extension phone

address(the 1

st

kind) ----- ------------------------------------ -- -------- ------- ---- -----------9

7.Table 3.3 comparative table of initializating room number and extension phone

address(the 2

nd

kind) ----- -- --------------------------------------------- ------------------ - 10

8.Table3.4 comparative table of initializating room number and extension phone

address(the 3

rd

kind) ----- --------------------------------------- -- ------ ------------------ - 10

9.Setting of door station and extension phone number--------- ----- ------- --- -- 11-12

10.Door station setting order------------------------- - -------------------- - ------ -------- ---1 2

11.User ’ s operational order--------------------------------- -- -------------- - ---- -- -- -- -- 13-14

12.Wrong code form------------------------------------------- --- ------------ - ---- -- --- ------ -1 4

13.Setting the number of door station calling managing center--- ------ - -------- --1 5

14.Address setting instruction------------------------------------------------ --- ---- ------ --1 5

15.Managing center setting order---------------------------------------- ------ ---- ------ --1 5

16.System cable requirement---------------------------------------- --- --- -- -------- ------ -1 6

17.Wiring attentions--------------------------------------------------- ---- -- - - - --- - --- --- -1 7-19

1 8 .Wiring requirment and attentions ------------------------------------------- - --- ---19-21

www.cusamintercom.com

2

www.cusamintercom.com

3

1.Function

Introduction

◇Function

Function

of

managing

center

：

Call any indoor phone and be called by any indoor phone ;

Be called by door station and overlook photo of door station ;

Time show in digital screen

◇Function

Function

of

indoor

phone

：

Be called by door station and managing center ；

Call managing center and overlook door station automatically

◇Function

Function

of

door

station

：

Call indoor phone s and managing center,unlock the gate by password

2.Using

Method

◇Managing

Managing

center

call

indoor

phones

：input door station and

indoor phone number ，the corresponding indoor phone ring and user can talk

with managing center ；

◇Door

Door

station

call

managing

center

：

input specific number(999 o r

9999

）

then it can call and talk with managing center

；

and managing center ca n

unlock the gate ；If it is the video door station,meanwhile the photo will show on

managing center ；

◇Door

Door

station

call

indoor

phone

：input indoor phone number,call

and talk with corresponding indoor phone ，open the gate by press unlock

button ；If it is the video door station,meanwhile the photo will show on indoor

phone ；

◇Indoor

Indoor

phone

call

managing

center

：user can call and talk with

managing center by press the call button on indoor phone

；

If you dial the wron g

number,press “ # ” to cancel and repress.

www.cusamintercom.com

4

3.System

schematic

and

W

iring

diagram

(

1

)

System

structure

schematic

drawing

www.cusamintercom.com

5

(

2

)

system

wiring

diagram

Wiring

Instruction

Managing center to Audio and Video Switcher （Vi → GV 、VG → GGV 、

Audio +

+

→ GT 、Audio -→ GG ）

Audio and Video Swithcher

to

Door station （MT → T 、G→ G）

Network module

to

Video indoor phone （JP → L1 、F → L2 ）

www.cusamintercom.com

6

4

.

Code

setting

Managing

center---Door

station

number

(Building

number)

setting

There is a comparative table of door station number and Network switcher.

Input ” **15 ”

to

enter into this table,as follow steps ：

（1）**00 XXXX （the original manager password is 2098

）；

（2）**15 show A-01.00 （

A

stands address ，01.00 tells the first address i s

01 ，the second adress is 00 ）input three figures

to

change current adress ，

press “ * ” if you don ’ t want

to

change ；

（3）After finishing step （2）,the screen will show n-000

or

other three

figure s ，i n put three figures (that is door station number)if you want

to

change ，

press “ # ” if you don ’ t(say only check it) ，then it will show the next address that ’ s

need

to

be set 。If the three figures you in put have existed in the table(that ’ s say

repe titon ) ，then it will show the address of the repeat ing number 。If you input

000 means you don ’ t use this address.

If the code method of door station corresponds with rule of table 3.1 ，the

the managing center provides a quick order “ **31 ” 。Do as follows ：**00 、XXXX

（Manager password,the original one is 2098 ）**31 ，it will come

to

the

programming rule as table 3.1 does.Press* *30

to

cancel it.

Network

door

station

setting(Building

number)

：it is combined by the

two sides contact pin of Network Swithcher(that ’ s the first address)

and Audio and Video Switcher(that ’ s the second address) 。The

first address range from 1

to

15 ，and the second address range from 00

to

31

。

www.cusamintercom.com

7

△(e.g.)Setting

(e.g.)Setting

the

19

th

door

station

19-32*(N-1)=M+1 M=18 （N is the first address ，M is the second

address ）

The short-circuit block should be inserted in1 place of the Network

Switcher and 2,16 place of the Audio and Video Switcher

△(e.g.)Setting

(e.g.)Setting

the

52

nd

door

station

52-32*(N-1)=M+1 M=19 （N is the first address ，M is the sencond

address ）

The short-circuit block should be inserted in 2 place of the Network

Switcher and 1,2,16 place of the Audio and Video Switcher.

Comparative

table

of

Network

Door

Station

number

and

the

first

address

Door

Station

No.

001

…

032

033

…

064

065

…

096

097

…

128

129

…

160

The

first

address

1

2

3

4

5

Door

Station

No.

161

…

192

193

…

224

225

…

256

257

…

288

289

…

320

The

first

address

6

7

8

9

10

Door

Station

No.

321

…

352

353

…

384

385

…

416

417

…

448

449

…

480

The

first

address

11

12

13

14

15

www.cusamintercom.com

8

5.Table3.1

comparative

table

of

initializ

at

ing

the

first

building

door

station

number

and

Network

switcher

address

Managing

center---Indoor

phone

（room

room

number

）setting

setting

Managing center provides a comparative table of Network Modul e and

room number.

input “ **16 ”

to

enter into setting of this table ，the step s are the same with

door station number setting.

The address of Network Module can be 127.04 at most.If you want

to

code 100.01

or

above address,please enter from 99.04 and add by press* and

code when it comes

to

100.01

or

above.

Network

Switcher

address

(the first,the

second )

Door

station

NO.

Network

Switcher

address

(the first,the

second )

Door

station

NO.

Network

Switcher

address

(the first,the

second )

Door

station

NO.

Network

Switcher

address

(the first,the

second )

Door

station

NO.

1.00

001

3.00

065

5.00

109

7.00

193

1.01

002

3.01

066

5.01

110

7.01

194

┄

1.30

031

3.30

095

5.30

159

7.30

223

1.31

032

3.31

096

5.31

160

7.31

224

2.00

033

4.00

097

6.00

161

┄

2.01

034

4.01

098

6.01

162

┄

2.30

063

4.30

127

6.30

191

15.30

479

2.31

064

4.31

128

6.31

192

15.31

480

www.cusamintercom.com

9

Quick

setting

If code of room number corresponds with the rule of table 3.2 ，the

managing center provides a quick setting order “ **41 ” .Do as follows:**00 XXXX

（Manager password,the original one is 2098 ）**41 ，It will come

to

the

programming rule of table3.2.

If code of room number corresponds with the rule of table 3.3.Then

managing center provides a quick setting order “ **42 ” 。

If code of room number corresponds with the rule of table 3.4.Then

managing center provides a quick setting order “ **43 ” 。

Press “ **40 ”

to

cancel it.

6

、Table3.2

Table3.2

comparative

table

of

initializating

room

number

and

extension

phone

address(the

1

st

kind)

Module

address,coding

site

Roo m No .

Module

address,codin

g site

Roo m

No.

Module

address,codin

g site

Roo m

No.

Module

address,codin

g site

Roo m

No.

Y01.1

0101

Y05.1

0501

Y09.1

0901

Y13.1

1301

Y01.2

0102

Y05.2

0502

Y09.2

0902

Y13.2

1302

Y01.3

0103

Y05.3

0503

Y09.3

0903

Y13.3

1303

Y01.4

0104

Y05.4

0504

Y09.4

0904

Y13.4

1304

Y02.1

0201

Y06.1

0601

Y10.1

1001

Y14.1

1401

Y02.2

0202

Y06.2

0602

Y10.2

1002

Y14.2

1402

Y02.3

0203

Y06.3

0603

Y10.3

1003

Y14.3

1403

Y02.4

0204

Y06.4

0604

Y10.4

1004

Y14.4

1404

Y03.1

0301

Y07.1

0701

Y11.1

1101

Y15.1

1501

Y03.2

0302

Y07.2

0702

Y11.2

1102

Y15.2

1502

Y03.3

0303

Y07.3

0703

Y11.3

1103

Y15.3

1503

Y03.4

0304

Y07.4

0704

Y11.4

1104

Y15.4

1504

Y04.1

0401

Y08.1

0801

Y12.1

1201

…

Y04.2

0402

Y08.2

0802

Y12.2

1202

Y99.2

9902

Y04.3

0403

Y08.3

0803

Y12.3

1203

Y99.3

9903

Y04.4

0404

Y08.4

0804

Y12.4

1204

Y99.4

9904

Cusam CS-200ZW-1 User manual

Popular Intercom System manuals by other brands