Custom Audio Electronics ALITM02 User manual

GENERAL INSTRUCTIONS
Custom Engineering s.r.l. declines all responsibility for accidents or
damage to persons or property occurring as a result of tampering,
structural or functional modifications, unsuitable or incorrect installations,
environments not in keeping with the equipment’s protection degree or with
the required temperature and humidity conditions, failure to carry out
maintenance and periodical inspections and poor repair work.
The PSM05printer is in conformity with the essential Electromagnetic
Compatibility and Safety requirements laid down in Directives:
•89/336/EEC dated 3 May 1989 and subsequent revisions (Directive
92/31/EEC of 28 April 1992 and Directive 93/68/EEC of 22 July 1993);
•73/23/EEC dated 19 February 1973 and subsequent revisions (Directive
93/68/EEC of 22 July 1993);
inasmuch as it was designed and constructed in conformity with the
provisions laid down in the following Harmonized Standards:
•EN 55022 (Limits and methods of measurements of radio interference
characteristics of Information Technology Equipment);
•EN 50082-1 (Electromagnetic Compatibility - General Immunity
Standard - Part 1; Residential, commercial and light industry);
•EN 60950 (Safety of information technology equipment, including
electrical business equipment).
VERSION 1.00 DOFE-ALITM02
ALITM02
Switching power supply
USER MANUAL
The aim of this manual is to provide instructions to enable the customer to
make the best possible use of the product. Any suggestion regarding errors
in its contents or possible improvements will be greatly appreciated
The products are continuously checked and improved. For this reason
Custom Engineering S.r.l. reserves the right to modify the information
contained in this manual without prior notice
FOR FURTHER DETAILS PLEASE CONTACT :
CUSTOM ENGINEERING S.r.l.
Strada Berettine 2, 43010 Fontevivo, Parma (Italy)
Tel. [phone] Fax [phone]
R
The format used for
this manual
improves use of
natural resources
reducing the
quantity of
necessary paper to
print this copy.

Electrical Characteristic
Model ALITM02 ALITM02H
V1 Output +24Vdc ±5% 0 - 3,5A +24Vdc ±5% 0 - 3,5A
V2 Output +5Vdc ±5% 0 - 1,5A +5Vdc ±5% 0 - 1,5A
V3 Output +12Vdc ±5% 0 - 0,2A +12Vdc ±5% 0 - 2,5A
V4 Output -12Vdc ±5% 0 - 0,2A -12Vdc ±5% 0 - 0,2A
Input (1) 110Vac ±15% 220-240Vac ±15% 50-60 Hz 1,1A
(1) Input voltage selection with internal jumper
Connections
A Input connector
B Output connector +5Vdc +5Vdc +12Vdc -12Vdc GND GND GND GND
C Output connector GND +24Vdc GND +5Vdc
D Output connector GND +24Vdc GND +5Vdc
Protections
Main input Delayeds fuses 3.15A
+24Vdc Output Short circuit Overload Overvoltage
+5Vdc Output Short circuit Overload Overvoltage
+12Vdc Output Short circuit Overload Overvoltage
-12Vdc Output Short circuit Overload Overvoltage
Environmental Condition
Temperature -10 °C +50 °C
Relative humidity 5 % 90 % without condensing
Connection to the mains supply
Before connecting the power supply to the mains supply, ensure that the
supply voltage and frequency are the same as those indicated on the
sticker listing the machine’s characteristic, that the supply system is
earthed and protected by differential switch.
Verify that the absorption current doesn’t over-ride the maximum current of
power supply;