CyberPower RMCARD205 User manual

Quick Start Guide
REMOTE MANAGEMENT CARD
RMCARD205
RMCARD305
The Remote Management Card allows a UPS
system and environmental sensor to be managed,
monitored, and configured.
K01-0000449-00

1
INSTALLATION GUIDE
Step 1. Hardware Installation
1. Remove the two retaining screws
of the expansion port cover, and
then remove the cover.
2. Install the CyberPower Remote
Management Card into the
expansion port.
3. Re-install and tighten the retaining
screws.
4. Connect the Ethernet cable to the
Ethernet connector of the
CyberPower Remote Management
Card.
5. (Optional) To connect with the
environmental sensor, use a
RJ45 Ethernet cable. Connect
one end to the Universal port on
the RMCARD and the other end
into the sensor. For further
information, please refer to the
ENVIROSENOR user’s manual.
NOTE: The CyberPower Remote Management Card is a hot-swap device, so you do
not need to turn off the UPS to install it.
RMCARD205
RMCARD305

2
Definitions for LED Indicators
Link LED color
Condition
Off
The Remote Management Card is not connected to
the Network/ or the Remote Management Card
power is off
On(Yellow)
The Remote Management Card is connected to the
Network
TX/RX LED color
Off
The Remote Management Card power is off
On(Green)
The Remote Management Card power is on
Flash
- Receiving/transmitting data packet
- Reset finished
Step 2. Configure the IP address for the CyberPower
Remote Management Card.
Method 1: Using the Power Device Network Utility Tool
1. Install the Power Device Network Utility tool available for download on the
Network Power Management product web page at www.CyberPower.com.

3
2. After installation completes, run the “Power Device Network Utility”.
3. The main dialog of the Power Device Network Utility Tool program is
shown in Figure 1. The configuration tool will display all CyberPower
Remote Management devices present on the same network subnet. The
"Refresh" button is used to search the local network subnet again.
Figure 1. The main window of the “Power Device Network Utility” program.
4. Select the Remote Management Card you are setting up. Click on the
Tools menu and select “Device Setup” or double click the Remote
Management Card you want to configure.
5. You can modify the IP Address,
Subnet Mask, and Gateway address
for the Device MAC Address listed in
the Device Network Settings window,
as shown in Figure 2. The default IP
Address is 192.168.20.177 and the
default Subnet Mask is
255.255.255.0.
6. Modify the IP, subnet mask or
gateway address. Enter the new
addresses into the corresponding
fields.
Figure 2. The Device Network setting window.
Step 1. Hardware Installation
LINK Indicator
Ethernet connector
RX/TX Indicator
RMCARD203
Universal Link RX/TX
Universal connector

4
7. You will need to enter a User Name
and Password for the Remote
Management Card in the
authentication window, as shown in
Figure 3.
*Default user name: cyber
Default password: cyber
8. If the IP address change is
successful, you will see a message
confirming the IP set up is OK, as
shown in Figure 4.
Method 2: Using a command prompt
1. Obtain the MAC address from the label on the Remote Management Card.
Each Management Card has a unique MAC address.
2. Use the ARP command to set the IP address.
Example:
To assign the IP Address 192.168.10.134 for the Remote Management
Card, which has a MAC address of 00-0C-15-00-FF-99 you will type in the
following in the command prompt from a PC connected to the same
network as the Remote Management Card.
(1) Type in “arp -s 192.168.10.134 00-0C-15-00-FF-99” then press Enter.
3. Use the Ping command to assign a size of 123 bytes to the IP.
(1) Type in “ping 192.168.10.134 -l123” then press Enter.
(2) If the replies are received, your computer can communicate with the IP
address.
Note: These instructions are for Windows OS. For other OS please refer to RMCARD
User’s Manual available for download at CyberPower Systems official website:
www.CyberPower.com.
Figure 4. Setup IP Address successfully message.
Figure 3. Authentication window.

5
WEB INTERFACE Login User Account
You can select a preferred language, and will need to enter a User Name
and Password to login to the interface. There are two user account types.
1. Administrator
*Default username: cyber
Default password: cyber
2. View only
*Default username: device
Default password: cyber
The administrator can access all functions, including enable/disable the view
only account. The viewer can access read only features but cannot change
any settings.
Trouble Shooting
Problem
Solution
Unable to configure
the Remote
Management Card
by method 1 or
method 2
1. Check the LED status, the condition is normal
when the yellow and green LEDs are both on.
If green LED is off :
►Check if the Remote Management Card is
properly seated in the UPS and the UPS
power is connected to working electrical
outlet.
If yellow LED is off :
►Ensure the network connection is good.
2. Ensure the PC being used is on the same
network subnet as Remote Management Card.
Unable to ping the
Remote
Management Card
1. Use method 1 and method 2 to get/set a correct
IP address for the Remote Management Card.
2. If the PC being used is on a different network
subnet from the Remote Management Card,
verify the setting of subnet mask and the IP
address of gateway.
Lost the user name
and password
Please refer to the “Reset to Default Setting /
Recover from a Lost Password” section in the
RMCARD User’s Manual.

6
SOFTWARE SUPPORT
PowerPanel®Business Edition Client can support a UPS with a remote
management card via the network. PowerPanel® Business Edition software
is available on CyberPower Systems official website. Please visit
www.CyberPower.com and go to the software section for free download.
CONFORMANCE APPROVALS
FCC Warning
This equipment has been tested and found to comply with the limits for a
Class A Digital Device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
Any special accessories needed for compliance must be specified in the
instruction.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulation.
Cet appareil numerique de la class A respecte toutes les exigencies du
Reglement sur le materiel brouilleur du Canada.

7
CyberPower North America
CyberPower Systems (USA), Inc.
Phone: [phone] Toll-free: [phone]
4241 12th Avenue E. Suite 400, Shakopee, MN 55379
E-mail: [e-mail]
Website: www.CPSww.com
CyberPower International
CyberPower Systems, Inc.
Website: www.CyberPower.com