Cygnett V-PRO TRAVEL User manual

VPRO TRAVEL
USER MANUAL
Cygnett and the Cygnett logo are trademarks of Cygnett
Pty Ltd. Other brands and product names are trademarks
or registered trademarks of their respective holders.
© 2020 Cygnett PTY LTD.
Cygnett Head Oice
858 Lorimer Street, Port Melbourne
Victoria, 3207, Australia
Australian Consumer Law
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
Cygnett warrants this product against defects in
workmanship and material for a period of two (2) years
from its original purchase date. You must present
your receipt as proof of date of purchase for warranty
validation. Please read the following information carefully
and retain this for any warranty claim.
Terms & Conditions
• This product is for household use only. If the product
is used in a commercial environment, the warranty
period will be automatically reduced to three
(3) months.
• Cygnett warrants that, with normal use or service, the
product will be free from faulty parts, manufacture
or workmanship.
• The warranty does not apply where damage is caused
by other factors, e.g. mishandling, abuse, accident or
failure to follow operating instructions.
Caution
Please read all warnings for your safety and optimal user
experience. Please read and follow these instructions
carefully and retain for your records.
1. Do not disassemble or throw into ire or water.
2. Do not expose to extreme weather conditions.
3. This is not a toy and should be kept away from children.
4. In the case of the device overheating, please disconnect
immediately.
Please note that changes or modiications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment. Cygnett
takes no responsibility for damages caused by incorrect use
of its products. Made in China.
This symbol on the product indicates that this product
shall not be treated as household waste. Instead it shall
be sent to the applicable collection point for the recycling
of electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health. For more information about the recycling of this
product, please contact your local city oice.
WARNING: KEEP BATTERIES OUT OF REACH OF CHILDREN.
Swallowing may lead to serious injury in as little as 2 hours
or death, due to chemical burns and potential perforation
of the oesophagus. If you suspect your child has swallowed
or inserted a button battery immediately call the 24-hour
Poisons Information Centre on 13 11 26 for fast, expert advice.
Examine devices and make sure the battery compartment
is correctly secured, e.g. that the screw or other mechanical
fastener is tightened. Do not use if compartment is not
secure. Dispose of used button batteries immediately
and safely. Flat batteries can still be dangerous

Product Specifications
Name V-Pro Travel
Item Number CY3443VCSLR
Input Power 5V⎓2.7A (13.5W)
Light Mode Warm White
Neutral White
Cool White
Power Supply USB 5V
Device Width (mm) 60 – 85
FCC ID 2AEDZCYG2
A LED ring light
B Device holder
C Pan/tilt ball joint
D Tightening screw
E Metal tripod stand
F LED ring light controller
G Increase brightness
H Colour mode switch
I Power button
J Decrease brightness
AG
M
I
C
D
B
H
F
J
E
Installation
1. Loosen the tightening screw (D) and open up the metal tripod stand (E).
2. Tighten the screw (D) at the desired position.
3. Install the pan/tilt ball joint (C) onto the stand.
4. Install the LED ring light (A) onto the pan/tilt ball joint (C).
5. Install the device holder (B) onto the LED ring light (A).
6. Connect the LED ring light controller’s (F) USBA end into a compatible
USBA wall charger. For optimal user experience, use a wall charger that
supports up to 13.5W on a 5V supply.
7. Press the power button (I) to turn on the LED ring light.
A 1/4” thread adapter has been included. Swap this out with the device
holder (B) should you wish to install a camera within the LED ring light.
Bluetooth Instructions
Turn on the Bluetooth remote by switching the button on the side of the
remote to ‘ON’. Go into your device’s Bluetooth settings and connect to
‘Cygnett BT’. Use the corresponding shutter button on the remote to take an
image whilst in your camera app. Compatible with Android 4.2.2 OS or
newer, and iOS 6.0 or newer.
Colour Modes
The LED ring light has three dierent colour temperatures: warm white,
neutral white and cool white. Change between these modes by pressing the
colour mode switch (H).
Brightness Levels
To increase the brightness of the LED ring light, press the increase brightness
button (G) on the remote. To decrease the brightness of the LED ring light,
press the decrease brightness button (J) on the remote.
Adjusting the Height
Adjust the height of your stand by loosening and tightening any of the
three tightening screws found along the metal pole.
press the decrease brightness button (J) on the remote.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generations, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to connect
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help