d & b audiotechnik Z5357 User manual

ZZ5357
Mounting instructions 1.1 en

S
y
m
b
o
l
s
o
n
t
h
e
p
r
o
d
u
c
t
P
l
e
a
s
e
r
e
f
e
r
t
o
t
h
e
i
n
f
o
r
m
a
t
i
o
n
i
n
t
h
e
m
a
n
u
a
l
.
W
A
R
N
I
N
G
!
D
a
n
g
e
r
o
u
s
v
o
l
t
a
g
e
!
General information
Z5357 Mounting instructions
Version: 1.1 en, 04/2018, D2968.EN .01
Copyright © 2018 by d&b audiotechnik GmbH; all rights
reserved.
Keep these mountings instructions with the product or
in a safe place so that they are available for future
reference.
When reselling this product, hand over these mounting instructions
to the new owner.
d&b audiotechnik GmbH
Eugen-Adolff-Str. 134, D-71522 Backnang, Germany
T [phone], F [phone]
[email protected], www.dbaudio.com

1. Z5357 Mounting instructions......................................... 4
1.1. Safety precautions..................................................................... 4
1.2. Intended use............................................................................... 4
1.3. Scope of supply......................................................................... 4
1.4. Assembly.................................................................................... 5
1.5. Z5038 Fixing plate M10 option.............................................. 5
2. Manufacturer's declaration............................................ 7
2.1. Conformity.................................................................................. 7
2.2. Disposal...................................................................................... 7
Contents
d&b Z5357 Mounting instructions 1.1 en 3

1.1. Safety precautions
General safety
Installation and setup should only be carried out by qualified and
authorized personnel observing the valid national Rules for the
Prevention of Accidents (RPA).
It is the responsibility of the person installing the assembly to ensure
that the suspension/fixing points are suitable for the intended use.
Always carry out a visual and functional inspection of the items
before use. In case you have any doubt as to the proper
functioning and safety of the items, these must be withdrawn from
use immediately.
Load safety information
The maximum permitted working load of the Z5357 E4/E5 Ball
joint adapter is 3 kg (6.6 lb) which implies the weight of one E4 or
E5 cabinet.
1.2. Intended use
The d&b Z5357 E4/E5 Ball joint adapter must only be used in
conjunction with the d&b E-Series loudspeakers E4 and E5 as
described in these mounting instructions.
The adapter allows E4 and E5 cabinets to be connected to
different d&b mounting accessories such as:
▪ E6532 Super Clamp with
E6533 M10 adapter for Super Clamp
▪ Z5029 TV spigot
▪ Z5034 Stand adapter
▪ Z5035 M10 to 3/8" adapter
▪ Z5038 Fixing plate M10
Note: Refer to the specific mounting instructions for assembly
and operation of these accessories.
1.3. Scope of supply
Please verify the shipment for completeness and proper condition
of the items.
Qty. d&b Code Description
1Z5357 d&b E4/E5 Ball joint adapter [1].
Consisting of:
1 Set screw [2].
1 Fixing screws [3].
1 Threaded insert M10 [4].
1 Locking device [5].
1 D2968.EN .01 Mounting instructions.
Weight 0.5 kg / 1.1 lb
1. Z5357 Mounting instructions
d&b Z5357 Mounting instructions 1.1 en4

1.4. Assembly
Tools required:
▪ Open-ended spanner/wrench (size #17)
▪ Allen hex key 3 mm
Ball joint adapter
The ball joint adapter is equipped with a set screw [2]. It is used to
preset the clamping of the ball joint.
If necessary, adjust the set screw using the 3 mm Allen hex key.
Attaching the ball joint adapter to the cabinet
1. Attach the ball joint adapter to the M10 threaded insert on the
rear panel of the cabinet.
2. Fix the adapter to the cabinet by tightening the locking device
[5] accordingly.
Alternatively an open-ended spanner (size #17) can be used
for this purpose.
1.5. Z5038 Fixing plate M10 option
The Z5038 Fixing plate M10 can be used to mount the E4 or E5
cabinets to walls, ceilings or other surfaces.
Note: Refer to the respective mounting instructions which are
supplied together with the fixing plate.
If the cabinets are mounted to a wall, both horizontal or vertical
mounting is possible. If the cabinets are mounted to a ceiling, the
horizontal setup is recommended.
The following mounting options and angle settings are applicable
no matter whether the cabinets are mounted to walls or ceilings or
other suitable surfaces.
E4 loudspeaker
For the E4 cabinet, angles can be set from 0° to –50° (vertical
setup) or from 0° to –80° (horizontal setup).
E5 loudspeaker
For the E5 cabinet, angles can be set from 0° to –35° (vertical
setup) or from 0° to –75° (horizontal setup).
d&b Z5357 Mounting instructions 1.1 en 5

Attaching the assembly to the fixing plate
To attach the assembly to the fixing plate, proceed as follows:
1. Slacken the set screw [2] and the fixing screw [3] to release
the M10 socket [4] of the ball joint.
2. Attach the assembly and bolt down the threaded insert to the
mounting plate.
3. Tighten the M10 socket using the spanner (#17).
4. Set the desired angle of the cabinet and tighten the set screw
[2] and fixing screw [3].
d&b Z5357 Mounting instructions 1.1 en6

2.1. Conformity
This declaration covers:
▪ d&b Z5357 E4/E5 Ball joint adapter.
National standards and technical specifications
applied:
DIN 18 800, DIN 1055, DGUV Vorschrift 17, BGI 810-3.
Backnang, 2018-04-27
Frank Bothe,
Head of R&D
d&b audiotechnik GmbH
2.2. Disposal
When out of use the rigging components must be disposed of in
accordance with the national environmental regulations.
Ensure that damaged rigging components are disposed of in a
way that they cannot be used again.
2. Manufacturer's declaration
d&b Z5357 Mounting instructions 1.1 en 7

D2968.EN .01, 04/2018 © d&b audiotechnik GmbH
www.dbaudio.com