D-Link DVG-2101S User manual

1
1. If you purchased this VoIP Telephone Adapter to share your high-speed
Internet connection with other computers, you must have an established
Internet account from an Internet Service Provider (ISP).
2. It’s best to use the same computer that is connected to your router for
configuring the DVG-2101S VoIP Telephone Adapter. The DVG-2101S acts
as a DHCP Client and will be assigned all the necessary IP address
information from your network. See the Quick Installation Guide or the Manual
on the CD-ROM for setting each network adapter to automatically obtain an
IP address.
Check Your Package Contents
If any of the above items are missing, please contact your reseller.
©2007 D-Link Corporation, Inc. All rights reserved. Trademarks or registered trademarks are the property of their
respective holders. Software and specifications subject to change without notice.
D
V
G-2101S
VoIP Telephone Adapter
Before You Begin
This product can be set up
using any current web browser,
i.e., Internet Explorer 6 or
Netscape Navigator 6.2.3.
D-Link D
V
G-2101S
V
oIP Telephone Adapter
CD-ROM (containing Manual and Q.I.G.)
Ethernet Cable
Phone Cable
12V, 1.5A Power Adapter
Quick Installation Guide
Using a power supply
with a different voltage rating
will damage and void the
warranty for this product.

2
Hardware Overview
Front Panel
Register LED
This LED will light solid if the phone
account registers successfully. This LED
will flash during registering and light off if
registering fails.
Power LED
This LED will light solid when the
device finishes a self-test and booting
up. This LED will flash during device
self-test and bootin
g
and li
g
ht off if
WAN LED
This LED will light solid when a
connection is established and
blink to indicate activity. If this
LED does not light up when a
cable is connected, verify the
cable connections and make
sure your devices are powered
on.
Phone LED
This LED will light solid
when the telephone is
off-hook. A fast blinking
LED indicates an
incoming call and a slow
blinking LED indicates a
message is waiting. This
LED will light off if the
phone connected to the
phone port is on-hook.
Provision LED
This LED will light solid if the
device provisions successfully.
This LED will flash during
provisioning and light off if
provisioning fails.

3
Rear Panel
Reset Button
Use a paper clip to:
1. Press 1-2 seconds to enable IVR.
2. Press 4-6 seconds to reset this unit.
3. Press 8-10 seconds to restore this
unit’s factory default settings.
Power Receptor
Connects to the provided
power adapter.
Phone Port
Connects to your
phone using a
standard phone cable
(
RJ-11
)
.
WAN Port
Connects to your
broadband modem
using an Ethernet
cable.

4
Configure IP Settings
To connect to the network, make sure the network adapter in your computer
is configured properly. Here’s how to assign a static IP address to your PC.
Select Properties.
Click on the
Network
Connections
icon.
Right-click the Local
Area Connection icon,
and then select
Properties.
Go to Start >
click Control
Panel > click on
the Network
Connections
icon.

5
Click Internet Protocol
(TCP/IP).
The dialog box displays a list
of currently installed network
items.
Make the choice to get the IP
address assigned manually.
Select Use the
following IP address
to get the IP settings
assigned manually.
Click OK.
Select Properties.

6
Initial Web Configuration
If your computer connects directly to a DSL or Cable modem and
does not connect to a router, follow the steps below to install your DVG-2101S.
For any other configuration, please refer to the user manual located on the CD-
ROM. After the steps are completed, your setup should look similar to the
diagram below.
1. Turn off your Computer.
2. Attach one end of the provided Ethernet
cable (blue) to the WAN port on the rear of
the DVG-2101S.
3. Attach the other end of this Ethernet cable
to the PC for initial configuration described
on the next chapter in this Quick
Installation Guide.

7
4. Attach one end of the provided phone
cable (gray) to a standard analog
telephone.
5. Attach the other end of the phone cable to
the phone port labeled PHONE on the
rear panel of the DVG-2101S.
6. Unpack the 12V DC Power Adapter that
came with the DVG-2101S. Connect the
power adapter to the power connecter on
the DVG-2101S.
7. Connect the other end of the power
adapter to an available electrical outlet
(wall socket or surge protector).
Note: Make sure all the cables are
connected tightly and properly.
8. Restart your PC. The corresponding LEDs would light on to indicate that the
DVG-2101S is ready for initial web configuration.
9. After finishing your initial configuration as described on the next chapter,
you need to unplug the Ethernet cable from the PC. And attach this end to
the LAN port of your router or Cable/DSL Modem.
The hardware configuration is now complete.

8
Initial Web Configuration
Open a Web browser and
type http://192.168.1.150 into
the URL address box. Press
the Enter or Return key.
When you first log
in, enter the User
name admin and
leave the Password
blank. These may
be changed later.
Click Setup Wizard.
Click Login button.
Setup Wizard will
guide you through the
quick setup steps.

9
Step 1
You can change the
login password during
this step or just leave
them the same as the
default values.
Step 2
Select your time zone
from the drop-down list.
Then select a NTP time
server or configure your
preferred time server.
Click Next.
Click Next.
Click Next.

10
Step 3-1
If you selected Static
IP, enter the IP
address, subnet mask
and gateway supplied
by your ISP.
Step 3-1-1
Static IP users have to
set the DNS address.
Step 3-1
If you selected Dynamic
IP, you may enter the
host name in the field.
Click Next.
Click Next.
Click Next.