D-Link DG-102S User manual

Comwave Home Phone Adapter
Quick Start Guide
Important: This guide describes the supported conguration for Comwave Home Phone Service. When
calling Comwave’s Technical Support Team, your network must be congured as described.
Home Phone Adapter
Package Contents
1
Connections
1 2
4
3
1 2 3 456
1 Power Adapter
2 Serial Cable
Used only if instructed by
Comwave to assist with
troubleshooting.
3 WAN
Used to connect to your High
Speed Internet modem using
the Ethernet Cable provided in
your package.
4 LAN
Used to connect to your computer using
an Ethernet Cable (if you are not using a
wireless router).
5 Phone 1
Used to connect to your telephone
handset, using your existing telephone
cord.
6 Life Line
NOTE: Dial“#”to activate this port.
Used to:
a) Connect to an existing phone
jack to access the building
intercom functions in apartment
buildings.
b) Connect to a back-up non-VoIP
land line in the event of Internet
loss, if a back-up line is available.
Output:12v 1

Start Here
Cable High Speed Internet
Go to page 3
If you have:
DSL High Speed Internet
with USERNAME and PASSWORD
DSL High Speed Internet
without USERNAME and PASSWORD
Go to page 3Go to page 5
2

Installation with a Cable Modem or DSL modem (without USERNAME and PASSWORD)
1
step
To begin installation, turn o your computer and disconnect the power adapter to
your High Speed Internet modem.
high speed
internet modem PC
telephone
power outlet
existing
cable or phone
line
2
steP
3
step
4
step
8
step
5
steP
6
steP
3
WAIT!!
2 min.

Connect an Ethernet cable from the High Speed Internet modem to the WAN
port of the Home Phone Adapter.
Connect a second Ethernet cable from the LAN port of the Home Phone Adapter
to your computer.
Connect your telephone handset to the PHONE 1 port of the Home Phone Adapter.
Connect the High Speed Internet modem to a power outlet.
Note: Please wait 2 minutes before continuing to the next step.
Connect the Home Phone Adapter to the power outlet . The Status light will blink
until it has successfully connected to the Comwave network. Once the Status
light stops ashing and becomes solid green, your phone is ready for use.
Your phone should now work.
Start your computer.
2
step
3
step
4
step
6
step
7
step
8
step
5
step
Remember to dial “1” before ALL calls, including local calls (example: 1-416-555-1234).
You will NOT be charged long distance for local calls.
Remember to dial “1” before ALL calls, including local calls (example: 1-416-555-1234).
4

1
step
To begin installation, turn o your computer and disconnect the power adapter to
your High Speed Internet modem.
Installation with a DSL modem (with USERNAME and PASSWORD)
high speed
internet modem PC
telephone
power outlet
existing
phone
line
2
steP
3
step
4
step
8
step
5
steP
6
steP
5
WAIT!!
2 min.

Connect an Ethernet cable from the High Speed Internet modem to the WAN port
of the Home Phone Adapter.
Connect a second Ethernet cable from the LAN port of the Home Phone Adapter
to your computer.
Connect your telephone handset to the PHONE 1 port of the Home Phone Adapter.
Connect the High Speed Internet modem to a power outlet.
Note: Please wait 2 minutes before continuing to the next step.
Connect the Home Phone Adapter to the power outlet.
Start your computer. Open a browser window, type “http://192.168.122.1:8089”
into the address eld and press the “Enter” key.
5
step
4
Continue to Step 8
7
step
step
3
step
2
step
6
step
6

Installation with a DSL modem (with USERNAME and PASSWORD)
Enter the following User Name
and Password, and click “OK”:
8
step
9
step
In the left menu, click on “Cong IP”
and then select “Cong Device IP Address”.
USER NAME: root
PASSWORD: admin

4
In the bottom right corner of the main
window, click the “Save” button . Then
on the left menu, select “Save Changes”
11
step
8
In the main window (under the section
called “PPPoE Settings”), ensure that the
dropdown menu is set to “enabled” .
Fill in the User Name and Password
provided by your Internet Service
Provider.
Note: It is important to be very accurate.
The user name and password are case
sensitive. Any mistakes will prevent your
Comwave Home Phone from working.
10
step
a
b
a
b
.

Installation with a DSL modem (with USERNAME and PASSWORD)
In the main window, click on the “Save Conguration” button. Your Comwave Home
Phone will reboot.
12
step