Dacor ER30D User manual

Use these instructions to change the trim color on the ER30D, ER36D and ER48D series ranges.
WARNING: To avoid burns, do not disassemble the range until it has cooled.
WARNING: To avoid personal injury, wear safety glasses during installation.
CAUTION: To prevent damage to the range, use only the tools indicated in these instructions.
NOTE: It is not necessary to pull the range out from the wall to change the trim color.
DANGER: Electric shock hazard! Before installation, disconnect power
at the circuit breaker or fuse box.
Trim Replacement Kit
AERTK30, AERTK36, AERTK48
INSTALLATION
INSTRUCTIONS
RANGE MODELS: ER30D, ER36D AND ER48D
Part No. 101516 Rev. E
Kit Part Number Identication
Tools Required
Phillips Head Screwdriver (4-40)•
Torx Driver (T20)•
2 Clamps• Range Size Trim Color
CH = Chrome
CP = Copper
BR = Brass
BC = Black Chrome
AERTKXXYY
Parts included with this kit
Trim Rings
30-Inch Ranges (4)
36 and 48-Inch Ranges (6)
Door End Caps
30 and 36-Inch Ranges (2)
48-Inch Ranges (4)
Range End Caps (2)
Extra Screws
<COMPANY NAME>
SCALE:2:1
SIZE
DWG. NO.
A
REV.
MATERIAL
FINISH
--
--
DO NOT SCALE DRAWING
APPLICATION
USED ON
NEXT ASSY
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL ±
ANGULAR: MACH ±
BEND ±
TWO PLACE DECIMAL ±
THREE PLACE DECIMAL ±
NAME DATE
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
SHEET 1 OF 1
WEIGHT:
COMMENTS:
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Part #
101505
Part #
83669
Part #
83571
Screw Part # Use Quantity
ER30D ER36D ER48D
101505 End Caps 2 2 2
83571 Trim Rings 12 18 18
83669 Handle End Caps 2 2 4
100385 Handle Mounting 2
100026 Handle Mounting 2 4
Part #
100026
Part #
100385

Page 2
Trim Kit Installation Instructions
STEP 1: Disconnect power to the range at the junction or fuse
box.
Trim Ring Replacement
STEP 2: Remove the knobs. Pull straight out to
remove them. Put them in a safe place to
prevent damage.
IMPORTANT: To prevent the parts behind the control
panel from being misaligned, remove only one trim ring
at a time.
STEP 3: Remove the three (3) Phillips head screws
that hold the existing trim ring in place. Note
the position of the blue LED light located
behind the trim ring.
STEP 4: While making sure the LED remains in
place, put the new trim ring into position.
Tighten it in place with the three (3) Phillips
head screws.
STEP 5: Repeat steps 3 and 4 for the remaining trim rings.
STEP 6: After all the trim rings are replaced, check to make
sure they are all properly aligned, that the LEDs
are in the proper place, and that the screws are
tightened.
STEP 7: Attach the knobs. Align the “D-shaped” opening on
the back of the knob with the end of the valve shaft.
Carefully push the knob on until it stops.
For Models ER36D and ER48D, put the knobs with
the words “MAX GRIDDLE” on them on the inner
(center burner) valve shafts.
For ER30D, place the “MAX GRIDDLE” knobs in
the 2 right hand valve shafts. Put the remaining
knobs on the remaining valve shafts.
Screws
LED
Trim Ring
Knob
CAUTION: To prevent damage to the griddle included with the range or
the optional grill, do not install the griddle knobs in the wrong position!
ER36D and ER48DER30D

Trim Kit Installation Instructions
Page 3
Range End Cap Replacement
STEP 8: Locate the right end cap screw access
hole under the right side of the front
panel overhang. Remove the 4-40 X
1/2 phillips head screw.
STEP 9: Pull the end cap out of the side of the
range to remove it. Insert the new end
cap in its place.
STEP 10: Thread the end cap screw and tighten
by hand. Do not over-tighten.
STEP 11: Repeat sets 8 - 10 for the left end cap.
Door End Cap Replacement
STEP 12: Open the oven door to the horizontal
position.
STEP 13: On model ER30D and ER48D, to prevent damage to the
door glass and door: Firmly tape or clamp both sides of the
door three (3) inches from the top to prevent it from coming
apart when the handle screws are removed. CAUTION: Do not
overtighten. Damage may occur. If clamps are used, pad both
sides of the clamp to prevent damage to the door surfaces.
STEP 14: On model ER36D: Remove the two (2) door screw
covers.
STEP 15: Grasp the handle with one hand and remove the two (2) torx
screws that hold it in place.
Screw
End Cap
Access Hole
Handle Screw cover
2 places
Screw,
2 places
Clamp
Handle
Pads
Clamp
Pad
ER36D
ER30D and ER48D

Dacor●600AntonBlvd.Suite1000CostaMesa,CA92626●Phone:(800)793-0093●Fax:(626)403-3130●www.Dacor.com
STEP 16: Remove the two (2) torx screws from the bottom of the
handle.
STEP 17: Pull the end caps off the end of the handle and replace
them with the new ones.
STEP 18: Thread the two (2) torx head screws into the handle and
tighten them into place. CAUTION: Do not overtighten.
Tighten only by hand.
STEP 19: Line up the screw holes on the handle with the mounting
holes on the oven door. Make sure the screws that hold the
end caps in place face toward the bottom of the door.
STEP 20: Thread the two (2) screws through the door and into
the handle. Tighten them into place. Do not overtighten.
Damage to the door or the door glass may result.
STEP 21: On model ER36D: Replace the screw covers.
STEP 22: Remove the clamps or tape from the door.
Handle
Screw,
2 places
End Cap,
2 places