Dacor EDWH24S Technical manual

PLANNING
GUIDE
10.4
Specications subject to change without notice. Phone: [phone]www.dacor.com
EDWH24S, IDWH24
24” Wide Built-In Dishwasher
A
B
Front
Drain hose
C
D Handle depth
2” (50.0 cm)
5 1/4” (13.5 cm) to
7 1/4” (18.5 cm)
Depth with door closed
Depth dimensions allow
for hose on back of unit
49 3/4” (126.4 cm)
Depth with door open
Side
3 1/4" (8.3 cm) 2 3/4" (7.0 cm)
Back
Do not modify
loop in hose
54” (137.0 cm)
long
Drain hose
44” (112.0 cm)
long
Power cord
Water supply line
60” (152.0 cm)
long
Product Dimensions
Model EDWH24S Model IDWH24
Front Panel Type Stainless steel Integrated
front panel2
(A) Width 24” (61.0 cm) 23 1/2” (59.7 cm)
(B) Height 34 3/8” (87.4 cm) to
36 1/2” (92.7 cm)
34 1/8” (86.7 cm) to
36 1/8” (91.8 cm)4
(C) Depth 22 7/8” (58.1 cm) 22 7/8” (58.1 cm)5
(D) Handle Depth Epicure®: 2 1/2” (6.4 cm)1
Millennia®: 2” (5.1 cm)2NA
1Epicure handle kit PN: ADWE24H
2Millennia handle kit PN: ADWM24H
3Model IDWH24 requires installation of a customer provided, custom
overlay door panel. A custom overlay panel allows you to blend the exterior
of your dishwasher into the overall kitchen décor. See page 2/3 for more
information.
4Height with required trim kit installed.
5Without custom front panel installed.
Product tolerances: ±1/16” (±1.6 mm)
otherwise stated
Document # PG10-005 Revised 08/10/11 Page 1/3
WARNING
• Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
• This appliance must be installed in accordance with the
accompanying installation instructions.
UTILITY CONNECTION DIMENSIONS
EPICURE STYLE HANDLE DIMENSIONS (PN ADWE24H)
MILLENNIA STYLE HANDLE DIMENSIONS (PN ADWM24H)
Approximate
Shipping Weight
108 lbs. (49 kg.).
B
A
CA
B
C
A = 7/8" (2.2 cm) B = 18 1/2" (47.0 cm) C = 2 3/8" (6.0 cm)A = 1 3/8" (3.5 cm) B = 23" (58.40 cm) C = 2" (5.1 cm)

PLANNING
GUIDE
10.5
Specications subject to change without notice. Phone: [phone]www.dacor.com
Electrical Specifications
Dedicated Circuit Required Total
Connected Load
Grounded, 3-prong, electrical outlet
supplied by 120 Vac,
60 Hz, 15 Amp. (circuit breaker)
11 Amp. @ 120 Vac, 60 Hz.
■The above specifications are for reference only. For exact
specifications see the product data label, located inside the right door
■Do not modify the power cord or use an extension cord. The power
cord may be disconnected from the appliance and hard-wired to a
junction box connected to a circuit meeting the above specifications if
the power cord is not long enough.
Water Supply Specifications
■Water Pressure: 4.2 to 125 p.s.i. (30-862 kPa) with minimum water
flow of 3 gallons (12 liters) per minute.
■Water Supply Temperature: Cold or hot water supply (max. 140°F,
60°C) may be used. Dacor recommends a hot water supply of 120°F
(49°C) to 140°F (60°C). If a cold water supply is used, washing times
will be longer but performance will not be affected.
■Water Supply Valve Requirement: 3/8” water supply valve for
connection to dishwasher’s water supply line is required in a location
where it is easily accessible after the dishwasher is installed. The
dishwasher water supply line is equipped with a 3/8” (1.0 cm) NPT
female compression fitting on the end.
Location Specifications
■Install in a location with convenient access, close to the kitchen sink
for easy water supply and drain connection. All minimum product
dimensions must be met or exceeded. Dimensions shown on this
page provide the required clearances.
■The cabinet must enclose the dishwasher on top, back and sides.
■Plan the installation so that the appliance can be removed easily if
service is required. The electrical outlet/junction box, water supply
valve and drain connection must be installed to the right or left of the
cutout and accessible when dishwasher is installed.
■If dishwasher is installed in a corner, there must be a minimum
clearance of 2” (5.1 cm) from the side wall so the door can open. See
diagram.
EDWH24S, IDWH24
24” Wide Built-In Dishwasher
24” (61.0 cm)
23 5/8”
(60.0 cm)
Power cable/water
supply access hole(s)
1 ½” x 1 ½” max.
(3.8 cm x 3.8 cm)
Drain line access
hole 2” x 2”
(5.1 cm x 5.1 cm)
E
F
DISHWASHER CUTOUT - FRONT VIEW
Cutout tolerances: +1/16” (+1.6 mm), -0
Document # PG10-005 Revised 08/10/11 Page 2/3
2” (5.1 cm) min.
clearance
Model (F) Cutout Height
EDWH24S 34 1/2” (87.6 cm) to 36 1/2” (92.7 cm)**
IDWH24* 34 1/8” (86.7 cm) to 36 1/8” (91.8 cm)**
*Model IDWH24 requires installation of a trim kit (Dacor PN 106925) to fill
the space between the edge of the cutout and the dishwasher.
** If the height of the existing cutout is too low:
■Check to see if the cabinet face can be trimmed at the top. In many
cases, when a non-standard size dishwasher has been installed
previously, there is enough room inside the cabinet once the cabinet
face is modified.
■The dishwasher can be shortened 1/4” (6.0 mm) by not installing the
plastic feet provided with the unit. Extra care must be taken if the feet
are not installed. Dacor is not responsible for floor damage during
installation.
■The dishwasher can be shortened 1/4” (6.0 mm) by removing the trim
pieces that surround the wash compartment opening. NOTE: Doing
so will create a gap of 1/4” (6.0 mm) on the right and left side of the
door.
■Floor must be solid and level. All cutout surfaces must be at right
angles. Surrounding cabinet must have sufficient material for
attachment of the anti-tip brackets (see installation instructions).
■The opening (E) through the partition between the drain connection
and the dishwasher cutout must be higher than the disposer or
waste tee connection (see page 3/3) and lower than 30” (76 cm). If
the partition is wood, the edges of the opening shall be smooth and
rounded. If the partition is metal, the edges of the opening shall be
covered with an edge protector.

PLANNING
GUIDE
10.6
Specications subject to change without notice. Phone: [phone]www.dacor.com
EDWH24S, IDWH24
24” Wide Built-In Dishwasher
Document # PG10-005 Revised 08/10/11 Page 3/3
EXAMPLE OF DRAIN CONNECTION WITHOUT AIR GAP
EXAMPLE OF DRAIN CONNECTION WITH AIR GAP
Drain Specifications
■The drain connection must be a minimum of 20" (50.8 cm) above the
floor. No part of the drain hose can be higher than 37 1/2” (95.0 cm)
from the bottom of the dishwasher.
■Should a drain hose longer than the one provided be required, use a
hose extension approved for detergents and high temperature water.
■Total drain hose length (including any extensions) must not exceed
14 ft. 9 in. (450.0 cm) in length from the top of the drain loop on the
back of the unit. Joints and joint tubes must have a minimum inside
diameter of 5/8” (1.6 cm).
■The drain hose supplied with the dishwasher must be connected
to a minimum 1/2" inside diameter drain connection. A clamp is not
supplied. The drain hose is equipped with a connector that fits drain
connections with an internal diameter of 1/2" to 7/8" (1.3 to
2.2 cm).
■Install an air gap in the drain system if required by local codes.
Plan the air gap location on the countertop area adjacent to the
dishwasher. A section of drain hose (not provided) needs to be
installed from the air gap to the drain connection.
■If an air gap is not required, the drain hose must be installed to a
disposer inlet or waste tee above the drain trap in the household
plumbing.
20"
min.
20"
min.
G
H
J
Custom Panel/Handle for Model IDWH24
■The custom panel mounting screws are provided with the dishwasher.
Follow the panel dimensions below to ensure that the custom overlay
panel will fit properly.
■The handle and handle mounting hardware are not included with
model IDWH24. A handle designed for use with an appliance should
produce satisfactory results. Do not use a knob or handle attached
by a single fastener. Instead use a handle with a larger D-style
pull. The panel craftsman must determine and obtain the proper
handle fasteners for the application. Handle screw heads must be
countersunk into the panel before panel installation.
(G) Height (H) Width (J) Thickness
30 1/8” (76.5 cm) 23 3/4” (60.3 cm) 3/4” (1.9 cm) min.
IMPORTANT: If the door panel weighs more than 15 pounds, you must
order the optional heavy duty door springs (Dacor PN 701385). Maximum
panel weight with heavy duty springs: 23 pounds.
CUSTOM PANEL
DIMENSIONS