Daewoo Cyclone Digi-Flex User manual

1
Cyclone Digi Flex Cordless Vacuum
FLR00041
User Manual
IMPORTANT –RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE

2
Cyclone Digi Flex Cordless Vacuum
FLR00041
User Manual
IMPORTANT –RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should
always be followed. These instructions should be saved for future
reference:
•Read and familiarise yourself with all operating instructions before
using this Vacuum Cleaner.
•Before plugging your unit into the mains, visually check that the unit is
intact and has not suffered any transit damage.
•Check that the voltage indicated on the data plate corresponds with
that of the local network before connecting the appliance to the mains
power supply.
•This appliance can be used by persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved.
•Children shall not play with the appliance.
•Keep the appliance and its cord out of reach of children less than 8
years when it is energised or cooling down.
•Do not immerse the appliance or its cord in water or any other liquids.
•Do not leave the appliance unattended during use.
•Do not leave the appliance unattended whilst connected to the mains
supply.
•Do not use this appliance outdoors.
•It is imperative to unplug the power cord after the appliance has been
used, before it is cleaned and whilst being repaired.
•Repairs to electrical appliances should only be performed by a qualified
electrician. Improper repairs may place user at serious risk.
•Do not operate this appliance with a damaged plug or cord, after a
malfunction or after being dropped or damaged in any way.
•Regular, periodic checks should be carried out on the mains cable to
•ensure no damage is evident. Should there be any signs of damage the
appliance should not be used.
•If the power cable is damaged, it should only be replaced by the
manufacturer or a suitable qualified after-sales-service in order to
avoid a hazard
•Do not allow the mains cable to hang over sharp edges or come in
contact with hot surfaces.
•Allow the unit to cool before storage.
•Before cleaning, disconnect the appliance from the mains supply and

3
Cyclone Digi Flex Cordless Vacuum
FLR00041
User Manual
IMPORTANT –RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
allow to cool.
•This appliance is intended for household use only and should not be
used for industrial purposes.
•Do not use any accessories or attachments with this appliance other
than those supplied or recommended by supplier.
•Do not use this appliance for anything other than its intended use.
•Do not push objects into any openings as damage to the appliance
and/or electric shock may occur.
•Unplug after each use. Grasp the plug, not the cord.
•Do not pull or carry the Vacuum Cleaner by the electrical cord, use the
handle provided.
•Ensure fingers and other objects are never placed in any part of the
vacuum cleaner. Clothing or hair may become trapped if thevacuum is
used improperly.
•Keep hair, loose clothing, jewellery, fingers and all parts of the body
away from openings and moving parts.
•Keep all air vents clear and free of dust, lint, hair and anything else that
may reduce airflow.
•Avoid directing the appliance towards naked flames as the air
discharged may extinguish gas fires or pilot lights and may disturb
ashes in open fires.
•Do not Vacuum water or any other liquids with this vacuum.
•Do not Vacuum hot ashes or lit cigarettes, etc.
•Never use the appliance without the filter in place.
•Do not use the Vacuum without the Dust Compartment attached.
•Do not vacuum any large or broken objects such as glass.
•Do not vacuum anything that is burning or smoking such as cigarettes,
matches or hot ashes.
Waste batteries should not be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or retailer for recycling advice.

4
Cyclone Digi Flex Cordless Vacuum
FLR00041
User Manual
IMPORTANT –RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
Description of Parts
Description of Parts –Accessories
3
1. Dust Release Catch
2. Hepa & Cyclonic Filters
3. Dust Compartment
4. Dust Compartment Catch
5. Air Outlet
6. Motor Housing
7. Display Panel
8. On/Off Trigger Switch
9. Handle
10.Battery Compartment
11.Charging Socket
12.Battery Compartment Catch
13.Air Intake
14.Attachment Release Catch
15.Dust Compartment Cover
16.Motorise Floor Tool
17.Crevice & Upholstery Tool
18.Small Power Plug
19.Mains Charger
20.Wall Mount Bracket
21.Aluminium Flexi-Tube
22.Carpet Brush
23.Hard Floor Roller
24.Long Reach Crevice Tool
15
13
14
8
10
7
1
16
17
18
21
6
20
19
5
22
23
4
24
2
11
12
9
22.Carpet Brush
23.Hard Floor Roller
24.Long Reach Crevice Tool
25.Information Screen
26.Battery Charge Display
27.Dust Sensor Failure
28.High Speed
29.Intelligent AUTO Mode
30.Battery Indicator
31.Brush Blockage Indicator
32.Air Intake Blockage Indicator
33.Eco Speed
34.Speed/Suction Indicator
26
25
27
28
29
30
31
32
33
34

5
Cyclone Digi Flex Cordless Vacuum
FLR00041
User Manual
IMPORTANT –RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
Before the first time you use your Cordless Vacuum Cleaner
Please read these operating instructions thoroughly and keep them in a safe place for future
reference.
Remove all packing materials and discard responsibly.
Charging the internal Battery
Before use, please ensure that the internal rechargeable battery is fully charged as follows:
1. Insert the Small Power Plug (18) of the Mains Charger (19) into the Charging Socket (11).
2. Plug the Mains Charger (19) into the nearest mains socket.
3. The Battery Indicator (30) will flash green and the Battery Charge Display (26) will count
up to 100% as the internal battery charges.
4. Once the battery is fully charged (after approximately 5 hours), the Battery Charge Display
(26) will display 100 (arrowed below) showing that the internal battery is 100% fully
charged and the Mains Charger (19) can now be removed.
Attaching the Accessories
CAUTION Ensure that the vacuum cleaner is not connected to the mains charger before use.
The Floor Attachment
1. Push the Aluminium Flexi Tube (21) onto the Air Intake (13) until it clicks home as shown
below:
2. Push the Motorised Floor Tool (16) onto the other end of the Aluminium Flexi Tube (21)
again until it clicks home.
NB The internal battery will need
recharging when the Battery
Indicator (30) flashes red and the
Battery Charge Display (26) reads a
low value (less than 10%). Follow
the above procedure (1 –4) to
recharge the internal battery.

6
Cyclone Digi Flex Cordless Vacuum
FLR00041
User Manual
IMPORTANT –RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
Using Your Cordless Vacuum Cleaner
The Motorised Floor Tool (16)
3. Place the brush bearing (c.) onto the end of the Hard Floor Roller (23) as shown above
left. Once in place, insert the Hard Floor Roller (23) into the Motorised Floor Tool (16) as
shown above right.
3
c.
1. Before using the Motorised Floor Tool (16),
first choose the appropriate brush type for
the floor type being cleaned:
Select the Carpet Brush (22) for vacuum
cleaning carpets, rugs, etc.
Select the Hard Floor Roller (23) for
cleaning vinyl, laminate, tiled floors, etc.
1
2. To change the brush attachment,
slide the catch (a) to the left and lift
up the brush bearing retaining clip (b)
on the underside of the Motorised
Floor Tool (16) as shown left.
NB the Carpet Brush (22) is currently
fitted in this example.
Lift out the Carpet Brush (22) and the
brush bearing (c). Remove the brush
bearing from the Carpet Brush (22).
2
a.
b.
c.
c.
4. Finally, hook the brush bearing retaining
clip at the front edge (d) and push down
into until it clicks into place (e) as shown
left.
The vacuum is now ready to clean hard
floors.
4
c.
d.
e.

7
Cyclone Digi Flex Cordless Vacuum
FLR00041
User Manual
IMPORTANT –RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
Using Your Cyclone Digi-Flex Vacuum
1. Right: Grasp the vacuum cleaner firmly by
the Handle (9) and press the On/off
Trigger Switch (8) to power up the
cleaner.
1
3. Right: Place your foot gently on the Motorised
Floor Tool (16) and pull the cleaner back by the
Handle (9) and start vacuum cleaning.
Press the On/off Trigger Switch (8) again at the
end of cleaning to switch the cleaner off.
Far Right: Press the catch on the Flexi joint
(arrowed right) to release the Aluminium Flexi
Tube (21) so that the tube can bend in order to
clean under furniture and other close to the
ground objects.
3
4. Left: If the Aluminium Flexi Tube (21) is not
required, the Motorised Floor Tool (16) can
be attached directly to the vacuum as shown
left for cleaning hard to get at areas such as
stairs, car seats, etc.
4
2. Left: During use, on the Information
Screen (25), press the Eco Speed (33) to
lower the vacuum speed/suction or High
Speed (28) to increase speed/suction. The
Speed/Suction Indicator (34) will move to
show the current speed/suction level (low
to high).
2
33
28

8
Cyclone Digi Flex Cordless Vacuum
FLR00041
User Manual
IMPORTANT –RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
Using the Crevice & Upholstery Tool (17)
1. Attach the Crevice Tool & Upholstery Tool (17) onto the Aluminium Flexi Tube (21) to
clean carpet edges and hard to get at areas:
2. If the Aluminium Flexi Tube (21) is not required, attach the Crevice Tool & Upholstery
Tool (17) directly to the cleaner, this useful for cleaning soft furnishings, car seats, stairs,
etc.:
Left: Slide the brush back on
the tool to reveal the crevice
tool to clean carpet edges,
etc. Alternatively use the
Long Reach Crevice Tool
(24).
Right: Pull the brush down
on the tool to clean curtains,
upholstery, etc.
Above: Using the Crevice Tool &
Upholstery Tool (17) on Upholstery.
Above: Using the Crevice Tool &
Upholstery Tool (17) to clean the car.

9
Cyclone Digi Flex Cordless Vacuum
FLR00041
User Manual
IMPORTANT –RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
1. Once the dust level reaches the ‘MAX’
mark (arrowed left) on the Dust
Compartment (3) it will need emptying
and the filters cleaned.
3. Hold the Dust Compartment (3) and
press the Dust Compartment Catch
(4) arrowed left and lift up the dust
compartment and remove.
2. To empty the cleaner, hold the Dust Compartment
(3) over a dust bin as shown right and press the
Dust Release Catch (1) (arrowed right) and the
Dust Compartment Cover (15) of the dust
compartment will swing open and allow the
collected dust to fall out into the dust bin.
Emptying and Cleaning Your Cyclone Digi-Flex Vacuum Cleaner
WARNING Always disconnect the cleaner from the mains charger before cleaning.
WARNING do not continue to use your vacuum cleaner once the ‘MAX’ mark has been
reached as permanent damage may occur to the appliance.
1
2
3

10
Cyclone Digi Flex Cordless Vacuum
FLR00041
User Manual
IMPORTANT –RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
4. Remove the Hepa & Cyclonic Filters
(2) from the Dust Compartment (3)
as shown right:
5. Above: Wash the Hepa & Cyclonic Filters (2) in warm running water until
clean. Allow the filters to dry thoroughly for 24 hours before reuse.
5
4

11
Cyclone Digi Flex Cordless Vacuum
FLR00041
User Manual
IMPORTANT –RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
6. Left: First replace the Hepa Filter inside the
Cyclonic Filter, rotate the Hepa filter
clockwise to lock it onto the Cyclonic Filter
as shown.
8. Left: Replace the Dust Compartment
(3) onto the vacuum by hooking the
dust compartment on and pushing it
down until it clicks home as shown.
7. Right: Replace the Hepa & Cyclonic Filters (2)
into the Dust Compartment (3) as shown.
Replacing the Filters in Your Cordless Vacuum Cleaner
Care and Use of your Cordless Vacuum Cleaner
•Always disconnect the cleaner from the mains charger before cleaning.
•Clean outside of the cleaner with a clean damp cloth. Never clean with harsh or abrasive
cleaners.
•Do not submerge the cleaner or its charger in water or any other liquids.
•Empty the Dust Compartment (3) as soon as the ‘MAX’ mark has been reached.*
•Wash the Hepa &Cyclonic Filters (2) regularly –see table below.
•Allow the filters to thoroughly dry out for 24 hours before reassembly and use.
*WARNING do not continue to use your vacuum cleaner once the ‘MAX’ mark has been
reached as permanent damage may occur to the appliance.
6
7
8

12
Cyclone Digi Flex Cordless Vacuum
FLR00041
User Manual
IMPORTANT –RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
Recommended filter cleaning intervals
Filter Type
Recommended cleaning period
WARNING Ensure the filters are cleaned periodically according to the table above, failure to
clean the filters regularly will severely impair the performance and permanent damage may
occur to the appliance and may invalidate your warranty.
Technical Specification
Model Number
FLR00041
Mains Charger
Input: AC 100-240V ~ 50/60Hz Output: 36V DC 500mA
Rated Power
250W
Battery
29.6V 2500mAh Li-Ion (8 cells)
Unpacked Weight (approx.)
2.2 Kgs
Dimensions (approx.)
328mm (l) x 110mm (w) x 220mm (h)
Vacuum (max)
≥24kpa
Noise Level (approx.)
72dB
Dust Compartment Capacity
0.8L
•Shake out debris when you empty the dust
container
• Rinse under war m water once a month
•Allow to dry thoroughly for 24 hours before reuse.
•Shake out debris once a month
• Rinse under war m water once a month.
•Allow to dry thoroughly for 24 hours before reuse.
Hepa Filter
Cyclonic Filter

13
Cyclone Digi Flex Cordless Vacuum
FLR00041
User Manual
IMPORTANT –RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
Troubleshooting Guide
Problem
Possible Cause
Solution
Unit fails to turn on.
Internal battery not
charged.
The charger is not plugged
into the mains socket.
Charge the internal battery.
Ensure the charger is fully
inserted into the socket and
the socket is switched on.
Low suction or poor pick-up.
Dust Compartment is full.
Filters are clogged.
Low Power Selected
Empty the cylinder.
Check and clean the filters.
Press the Min/Max Power
Button (8)
The vacuum is making a
“hissing” sound.
The airflow is restricted
Empty the Dust Compartment.
Check and clean the filters.
Clear any blockages if
necessary.
Brush Blockage Indicator
(31) not lit
The Carpet Brush (22) or
Hard Floor Roller (23) is
obstructed and/or tangled
with hair and debris
Switch off the vacuum cleaner
and remove obstruction from
the Carpet Brush (22) or Hard
Floor Roller (23).
Air Intake Blockage Indicator
(32) not lit
The Aluminium Flexi-Tube
(21) and/or vacuum Air
Inlet (5) are blocked.
Switch off the vacuum cleaner
and remove obstruction from
the Aluminium Flexi-Tube (21)
and/or vacuum Air Inlet (5)
Dust Sensor Failure (27)
Indicator not lit
The vacuum is very dirty
and/or blocked and the
Dust Compartment full.
Switch off the vacuum cleaner
and empty and clean the Dust
Compartment (3), Filters (2),
Aluminium Flexi-Tube (21)
and/or vacuum Air Inlet (5)
Waste electrical products should not be disposed of with household waste. Please
recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

14
Cyclone Digi Flex Cordless Vacuum
FLR00041
User Manual
IMPORTANT –RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE