Dahua VTS User manual

VTS User’s Manual
V 1.0.1

ii
Important Safeguards and Warnings
Please read the following safeguards and warnings carefully before using the product in
order to avoid damages and losses.
Note:
Do not expose the device to lampblack, steam or dust. Otherwise it may cause fire
or electric shock.
Do not install the device at position exposed to sunlight or in high temperature.
Temperature rise in device may cause fire.
Do not expose the device to humid environment. Otherwise it may cause fire.
The device must be installed on solid and flat surface in order to guarantee safety
under load and earthquake. Otherwise, it may cause device to fall off or turnover.
Do not place the device on carpet or quilt.
Do not block air vent of the device or ventilation around the device. Otherwise,
temperature in device will rise and may cause fire.
Do not place any object on the device.
Do not disassemble the device without professional instruction.
Warning:
Please use battery properly to avoid fire, explosion and other dangers.
Please replace used battery with battery of the same type.
Do not use power line other than the one specified. Please use it properly.
Otherwise, it may cause fire or electric shock.
Privacy Protection Notice
As the device user or data controller, you might collect personal data of others' such as
face, fingerprints, car plate number, Email address, phone number, GPS and so on. You
need to be in compliance with the local privacy protection laws and regulations to protect
the legitimate rights and interests of other people by implementing measures include but
not limited to: providing clear and visible identification to inform data subject the
existence of surveillance area and providing related contact.
About the Manual
The Manual is for reference only. If there is inconsistency between the
Manual and the actual product, the actual product shall prevail.
We are not liable for any loss caused by the operations that do not comply
with the Manual.
The Manual would be updated according to the latest laws and regulations

iii
of related regions. For detailed information, see the paper User's Manual,
CD-ROM, QR code or our official website. If there is inconsistency between
paper User's Manual and the electronic version, the electronic version shall
prevail.
All the designs and software are subject to change withoutprior written notice.
The product updates might cause some differences between the actual
product and the Manual. Please contact the customer service for the latest
program and supplementary documentation.
There still might be deviation in technical data, functions and operations
description, or errors in print. If there is any doubt or dispute, please refer to
our final explanation.
Upgrade the reader software or try other mainstream reader software if the
Guide (in PDF format) cannot be opened.
Alltrademarks,registered trademarks andthecompanynamesintheManual
are the properties of their respective owners.
Please visit our website, contact the supplier or customer service if there is
any problem occurred when using the device.
If there is any uncertainty or controversy, please refer to our final explanation.

iv
Table of Contents
Important Safeguards and Warnings...................................................................................ii
Special Announcement ............................................................
错误
!
未定义书签。
1. Product Overview.........................................................................................................1
1.1. Product Intro......................................................................................................1
1.1.1. Product Description................................................................................1
1.1.2. Features..................................................................................................1
1.2. Device Structure................................................................................................1
1.2.1. Front Panel.............................................................................................1
1.2.2. Rear Panel..............................................................................................3
2. Wiring............................................................................................................................5
2.1. Device Wiring.....................................................................................................5
2.2. Device Networking.............................................................................................5
3. Project Setup................................................................................................................6
3.1. Login Interface...................................................................................................6
3.2. Device Info.........................................................................................................6
3.3. Add VTH/Fence Station.....................................................................................7
3.4. SIP Server .........................................................................................................9
3.5. Add IPC ...........................................................................................................10
3.6. Call Test...........................................................................................................11
3.7. Default .............................................................................................................12
4. Daily Operation...........................................................................................................13
4.1. Monitor.............................................................................................................13
4.2. Call...................................................................................................................15
4.2.1. Shout.....................................................................................................15
4.2.2. Call Resident ........................................................................................16
4.2.3. Call Record...........................................................................................17
4.3. Message..........................................................................................................19
4.4. Unlock..............................................................................................................20
4.5. Version.............................................................................................................21
4.6. Basic Config.....................................................................................................21
4.6.1. Display..................................................................................................21
4.6.2. Ring.......................................................................................................21
4.6.3. Talk Time...............................................................................................22
4.6.4. SD Card................................................................................................23
4.6.5. Default...................................................................................................23
Appendix 1.........................................................................................................................24

1
1. Product Overview
1.1. Product Intro
1.1.1.Product Description
VTS as the contact center and service center of a system, can:
Bidirectional video walk among guest, VTH, VTO and fence station.
Monitor IPC, VTO and fence station.
Remote lock.
VTH, VTO can one-click call VTS.
1.1.2.Features
Easy operation, no installation required, bracket 0～45°adjustable.
Max manage 50 VTS.
Simultaneously multi-channel monitor, max support 4-ch 720P.
Capacitance touch screen 10 inch LCD, human-computer interaction.
Hands-free call and handset.
SD card expansion
2-ch USB port
1-ch HDMI output, max resolution 1024*600.
1.2. Device Structure
Device supports desktop position, and you can adjust its position and angle (0～45°) via
adjustment level at rear.
1.2.1.Front Panel
See Figure 1-1.

2
Figure 1-1
Please refer to the following sheet for detailed information.
No.
Parameter
Note
1 MIC Lifts MIC, audio and pickup are both on MIC.
2 Speaker Sound output.
3 Telephone Port Connect VTS and MIC.
4
Indicator
From left to right：
Power indicator
If the indicator is on, it indicates that the device is powered on.
If the indicator is off, it indicates that the device is not
connected to the power supply.
Information indicator
If the indicator light is on, it indicates that the device has a
missed call. The indicator light is off, indicating that the missed
call has been processed or there is no missed call.
Unlock button
In the status
of being called, monitoring status, call status
management machine, press the device on the unlock button,
you can remotely open the door machine door lock.
Hands-free button
Used to answer incoming calls, switch handsfree or Handset
mode.

Built-in MIC

3
No. Parameter Note
Sound input.
5 MIC （optional）can connect to external gooseneck MIC
6 Camera （optional）adjust up and down for camera angle
7
Display and
Touch
Screen and touch area.
1.2.2.Rear Panel
See Figure 1-2.
Figure 1-2
No.
Parameter
Note
1
Camera
Adjust camera angle up and down.
2 Port Open rear cover, ports from up to down：
HDMI video transmission port, for video only.
USB port.
USB port.
SD card slot.
3 Network
Port
Plug in RJ45 Ethernet cable.
4 12-pin
Port
Ports from left to right are：
Power output port
GNS

Alarm input port 1.

4
No. Parameter Note
Alarm input port 2.
Alarm input port 3.
Alarm input port 4.
Power input port.
GND.
RS485A port.
RS485B por.
Alarm output port NO.
Alarm output port COM.
5 Power
Port
DC 12V power
6 Bracket
Place VTS on desktop, adjust level to adjust VTH to an
appropriate position.

5
2. Wiring
2.1. Device Wiring
Please use our standard power supply, not self-powered.
Before wiring, please understand the structure of the device. For details, refer to Ch
1.2.
Before turning on the power, make sure all wiring is correct.Power running, the normal
working state for the power indicator light is always red.
2.2. Device Networking
See Figure 2-1.
Figure 2-1

6
3. Project Setup
Note:
Before operation, please make sure the device has properly wired, see Ch 2.1.
3.1. Login Interface
After device boots up, see Figure 3-1.
In login interface, enter login password, enter OK.
Note:
Default login password is 123456, and you cannot modify this password.
Figure 3-1
3.2. Device Info
Go to Config>Advance Config>Product Set Info, set no., local IP, subnet mask and etc,
see Figure 3-2.
Note:
Advance Config interface default login password is 888888, and you cannot modify
this password.
Please enter set IP address on Local IP field which must be in the same network